Post on 05-Jun-2018
WAC020
2
http://www.securitywireless.co.za
User Manual
Ver 1.0
Date Issued: 2015-07-01
All rights reserved.
GSM MMS Camera Alarm System
GSM MMS Camera Alarm System
Table of contents 1. Product details --------------------------------------------------------------------------------3
2. Safety Directions --------------------------------------------------------------------------4
3. Wiring Connection --------------------------------------------------------------------------5
4. How WAC02 works for you?----------------------------------------------------------------6
5. SMS Command-------------------------------------------------------------------------------7
5.1 Common operate commands-----------------------------------------------------------------------------------7 5.26LUHQDQGFDPHUD¶VPRWLRQdetector---------------------------------------------------------------------------7 5.3 $ODUPUHFHLYHU¶V3KRQHQXPEHU--------------------------------------------------------------------------------7 5.4 Edit DIN1~DIN8 zone name----------------------------------------------------------------------------------7 5.5 ',1a',1VHQVRU¶VW\SH----------------------------------------------------------------------------------------8 5.6 GPRS MMS parameters-----------------------------------------------------------------------------------------8 5.7 Email address-------------------------------------------------------------------------------------------------------8 5.8 Camera parameters-----------------------------------------------------------------------------------------------8 5.9 Other Settings-----------------------------------------------------------------------------------------------------9
6. Warranty --------------------------------------------------------------------------------9
This handbook has been designed as a guide to the installation and operation of WAC02 Alarm Panel. Statements contained in the handbook are general guidelines only and in no way are designed to supersede the
instructions contained with other products.
We recommend that the advice of a registered electrician be sought before any Installation work commences. The manufacturer, its employees and distributors, accept no liability for any loss or damage including
consequential damage due to reliance on any material contained in this handbook.
The manufacturer, its employees and distributors, accept no liability for GSM Network upgrading or SIM Card upgrading due to the technology specifications contained in this handbook.
Page 2 of 9 Ver 1.0
GSM MMS Camera Alarm System
1. Product details
The WAC02 GSM MMS Camera Alarm Controller is designed for taking on site photos and remote switching on/off machines
and equipment by SMS command. 8 channel digital inputs for different kinds of detectors like water leakage detector, door
contact sensors and so on. The camera include IR lights and motion detector. When alarm or motion is detected, WAC02 will send a
photo by MMS and alert with SMS to user. User can also add 2 e-mails for receiving pictures from WAC02.
ARM/DISARM button, arm and alarm delay, on site voice monitoring functions, you can install the WAC02 MMS Camera
Alarm controller for a lot of applications.
Smart phone APP available for easy configuration and operation.
Features:
z
z
z
z
z
z
z
z
z
z
z
GSM Quad-Band 850/900/1800/1900 MHz
External weather-proof camera with IR lights and motion detector 3 sizes for MMS Photo resolution optional
8 Digital input, alarm SMS text editable
1 Relay output can be switched on/off by SMS Commands
1 Siren output for warning while alarm occur
5 telephone numbers can be setup as dial or receive alarm SMS,MMS message
2 e-mails for receiving photos
Arm or disarmed by SMS commands or wired button
AC power lost and recovery alarm SMS.
Internal backup rechargeable battery with low power alarm buzzer
Applications:
z
z
z
Home intrusion security and surveillance alarm system
Warehouse, Factory, Office, Business, Summer house, ATM station security and surveillance alarm system.
Unmanned Station, Reservoir, Tower, Pump, Motor, Water Supply, BTS, Remote Area monitoring and surveillance alarm
system.
Specification and dimensions
GSM Frequency Quad-band 850/900/1800/1900MHz
Camera
Digital Input
External outdoor water-proof
8 NC/NO dry contact
1 Relay, 3A/240VAC
12VDC/1A
Digital Output
Siren Output
DC Power supply
Back up battery
Power consumption
SIM Card
9~24VDC/2A
7.4V/1000mAH
12V input Max. 50mA/Average 25mA
Supporting 3V SIM Card
ϱϬɏ^DŶƚĞŶŶĂŝŶƚĞƌĨĂĐĞ
-20~+60 °C
Antenna
Temperature range
Humidity range Relative humidity 90%
Page 3 of 9 Ver 1.0
GSM MMS Camera Alarm System
Standard Packing List
9
9
9
9
9
WAC02 GSM Main Unit *1 External Camera *1
Antenna * 1
AC/DC Power adaptor *1, User Manual CD x1
Optional Accessories: 9
9
9
9
9
9
PIR Motion Sensor, Door Magnetic contact Sensor,
Smoke detector
Gas leakage detector Water flood sensor
Water Level sensor
2.Safety Directions
Safe Startup
Do not use WAC02 where using GSM equipment is prohibited or might cause disturbance or danger.
Interference
Other wireless equipment might interfere with network signals of WAC02 and influence its performance.
Avoid Gas Station
Do not use WAC02 at a gas station. Switch off WAC02 when it is near fuels or chemicals.
Power off near Blasting Places
Please follow relevant restrictive regulations. Avoid using the device in blasting areas.
Reasonable Use
Please install the product at suitable places as described in the product documentation. Avoid signal shieldeding by covering the mainframe.
Use Qualified Maintenance Service
Maintenance can be carried out only by qualified maintainer. Do not break warrantee seals.
Page 4 of 9 Ver 1.0
GSM MMS Camera Alarm System 3. Wiring Connection
LED INDICATORS
Arm
Relay
Flash : Armed
Always Light ON: Disarm.
ON: Relay closed(ON)
OFF: Relay open (OFF)
Camera ON: Camera disconnected or wrong connection.
OFF: Camera on correct status.
Flash quickly: registering to cellular network.
Flash slowly: alarm or GPRS data communication.
OFF: registered to cellular network success.
I
III
Main Connection Terminals
TxD
RxD
5V
Data Transmitting (Blue)
Data Receiving (Yellow)
Camera Vdd (Black)
6V Power supply (Red)
Shielded wire GND
Connect one NC/NO button or switch on A+ and GND port, press the button to enter to Arm status, repress the button to Disarm.
Arm A+
S+
S--
NO
COM
+
ϭϮsнŽƵƚƉƵƚĐŽŶŶĞĐƚƚŽƐŝƌĞŶƐWŽƐŝƚŝǀĞǁŝƌĞ
GND, connect ƚŽƐŝƌĞŶƐEĞŐĂƚŝǀĞǁŝƌĞ
Normally Open port
Siren
Relay Common port
Power supply input, Positive wire(Red).
Power supply input, Negative wire(Black). Power In
_
Digital Input Zones
DC12V+ power supply for sensors. 12V+
Caution: Do not short circuit wire the DC12V+ to DIN1~8 inputs.
DC12V-- power supply for sensors. GND
DIN1~DIN4 GND
DIN1~DIN8 Digital Input, NC/NO dry contact(Voltage free) connection only!
Page 5 of 9 Ver 1.0
Digital Input
ANT Connect GSM antenna.
GSM MMS Camera Alarm System
4. How can WAC02 work for you?
z Start
¾ Insert mobile SIM card(GSM850/900/1800/1900MHz) in the SIM Card slot.
Connect the wiring of the camera and other digital sensors (if have) to the main unit.
Connect the power supply, Switch ON.
¾
¾
¾ If you had programmed your phone number on WAC02, it will send a status SMS to your phone once switched ON.
z Arm & Disarm
¾
¾
¾
(Recommend) Connect one button on the ARM (A+ and GND) port, you can press the button, after a 20 seconds
delay the system will enter Arm status and make 3 confirming beeps. You can also repress it for Disarm.
The DIN8 zone is for entrance purposes, when the sensor on DIN8 zone is triggered, it will delay 15 seconds alarm,
so you have 15 seconds to Disarm the system before alarming.
z Alarm
¾
¾
When alarm raised, WAC02 sends alert SMS and MMS picture to your phone and make a siren sound, you can
Answer the phone call to listen in on onsite voices or sounds.
zŽƵĐĂŶĞĚŝƚƚŚĞ/EϭΕϴƐnjŽŶĞŶĂŵĞƐŽLJŽƵ willƌĞĐĞŝǀĞƚŚĞcontent^D^ŵŽŬĞĂůĂƌŵ Žƌ
tĂƚĞƌĂůĂƌŵ Backdoor open or camera zone entered.
z Remote Control
¾ You can use APP or send SMS commands to switch ON/OFF the relay. To open the gate etc.
z Inquiry Photos
¾ You can use APP or send SMS commands to ask WAC02 to send back 1~20 photos to your mobile phone. Check if your dog food is fine. Measure your dam and see water levels. Protect and monitor any property.
z Power Monitoring
¾ You will receive alert SMS when AC/DC power failed and when it recovers. When the back up battery power low,
WAC02 will start alarming beeps to remind the user of such low power.
Page 6 of 9 Ver 1.0
You can also use APP of send SMS command to Arm/Disarm the system.
GSM MMS Camera Alarm System
5. SMS Command
¾
¾
WAC02 can be set by smart phone APP or SMS commands with password protection remotely.
The SMS commands should start with the Password. 1234 is the default password. Change to
a new password if you have not changed it already.
¾
¾
WAC02 will not return any message if the SMS command is not correct.
No spaces in the SMS commands, the spaces on the command list is for reading purpose only.
SMS Command Function Feedback SMS
Common Operate Commands
1234#00#
1234#01#
1234#02#
1234#03#
1234#04#
1234#05#
1234#06#
Inquire status
Disarm
Arm Status: Armed/Disarmed
Relay: Off/On Switch Relay OFF
Switch Relay ON
Switch Siren OFF
Switch Siren ON
Siren: Off/On
^ŝƌĞŶĂŶĚĐĂŵĞƌĂƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌ
1234#10#
1234#11#
1234#12#
1234#16#
1234#15#
Inquire settings
Siren ON when alarm occur Siren: ON/OFF
Siren OFF when alarm occur Motion Alarm: On/Off
ŶĂďůĞĐĂŵĞƌĂƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌĂůĂƌŵ;ĚĞĨĂƵůƚͿ
ŝƐĂďůĞĐĂŵĞƌĂƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌĂůĂƌŵ;ĚĞĨĂƵůƚͿ
Alarm Receivers phone number
1234#20##
1234#21#*#
1234#22#*#
1234#23#*#
1234#24#*#
1234#25#*#
/ŶƋƵŝƌe ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ TEL1:*******
TEL2:*******
TEL3:*******
TEL4:*******
TEL5:*******
st
Add the 1 ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ Add the 2nd ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ
rd
Add the 3 ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ th
Add the 4 ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ th
Add the 5 ƌĞĐĞŝǀĞƌƐƉŚŽŶĞŶƵŵďĞƌ
Edit DIN1~DIN8 Zone name
Inquire DIN Zone name DIN1:*****
DIN2:*****
DIN3:*****
1234#30#*#
1234#31#*#
*=1~8
Edit DIN1 Zone name
Page 7 of 9 Ver 1.0
GSM MMS Camera Alarm System 1234#32#*#
1234#33#*#
1234#34#*#
1234#35#*#
1234#36#*#
1234#37#*#
1234#38#*#
Edit DIN2 Zone name
Edit DIN3 Zone name
Edit DIN4 Zone name
Edit DIN5 Zone name
Edit DIN6 Zone name
Edit DIN7 Zone name
Edit DIN8 Zone name
DIN4:*****
DIN5:*****
DIN6:*****
DIN7:*****
DIN8:*****
*= Zone name, max.14 characters.
Default Alarm SMS content: DIN(1~8) Alarm!
DIN1~8 ^ĞŶƐŽƌƐType
1234#7*#0#
1234#7*#1#
*=1~8.
Setting the DIN* type as NO NO
NC Setting the DIN* type as NC
NC=Normally Close, NO=Normally Open.
Default type: NC.
GPRS MMS Parameters
1234#40##
1234#41#*#
1234#42#*#
1234#43#*#
1234#44#*#
1234#45#*#
1234#46#*#
Inquiry MMS settings Format:
Setting GPRS APN(Access Point Name)
Setting GPRS User Name
Setting GPRS Password
Setting MMSC IP address
Setting MMSC Port
APN:******
User:*******
Pass:******
IP:******
Port:****
MMSC Url:****** Setting MMSC URL
Notice: please call your mobile operator to ask the GPRS Access Point Name, User name, Password, MMSC IP, MMSC
Port and MMSC URL. If there is no User name or Password, etc needed for the GPRS connection, then leave it blank)
For example:
1234#41#everywhere#
1234#42#eesecure#
1234#43#secure#
the example APN name(everywhere), User name(eescure) Password(secure) supported by Orange UK.
E-mail address
1234#50## Inquiry e-mail address Email:********
Email 1:**** st
Setting the 1 e-mail address 1234#51#email address#
1234#51## st
Delete the 1 e-mail address nd 1234#52#email address#
1234#52##
Setting the 2 e-mail address Email 2:**** nd
Delete the 2 e-mail address
Page 8 of 9 Ver 1.0
GSM MMS Camera Alarm System
Camera Parameters
1234#60## Inquire settings
^ĞƚƚŝŶŐƉŚŽƚŽƐƌĞƐŽůƵƚŝŽŶ˖
*=0~2
1234#61#*# 0 =160X128;
1 = 320X240
2 = 640X480 (default) Image Size:640*480
Image Qty:1 Setting how many photos send out when alarm.
1234#62#*#
1234#63#*#
*=0~20 CamSensitivity:15
Default=1
ĚũƵƐƚĐĂŵĞƌĂƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌsensitivity
*=1~99
1 = the highest sensitive.
Default= 15
Other Settings
Inquiry the last photos 1234#90#*#
1234#99#*#
Require Image Ok *=1~20
Change password
*= 4 digits PASS: 1234
Change language to English, password reset to 1234. Language: English 1234#EN#
When AC/DC power goes off External AC Power Failure!
Control Panel AC Power
Recovery! When AC/DC power goes on
6. Warranty
1) 2)
This system is warranted to be free of defects in material and workmanship for one year.
This warranty does not extend to any defect, malfunction or failure caused by abuse or misuse by the Operating Instructions. In no event shall the manufacturer be liable for any alarm system altered by purchasers.
www.securitywireless.co.za
Page 9 of 9 Ver 1.0