GENERAL PLUMBING NOTES -...

DO NOT SCALE DRAWING

G IS C

LASSIFIE

LISHED

THE 1978

ACT, IT IS A

.NONE O

TECHNIC

SHEET M

EANS W

ITHOUT T

RESS P

RITTEN

RCHITECT.

N IS P

LOCATIO

SHEET T

ISSUE: P

SHEET NUMBER:

ISTA, AZ

41 2 3 5 6

L COOK

CHITECT│

EN, UT

7137│

ISTA, AR

IZONA 8

PRELIMINARY D

RAWING!

UCTION!

GENERAL PLUMBING NOTES

1. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT NECESSARY TO CONSTRUCT A COMPLETE, OPERATIONALPLUMBING SYSTEM FOR THE ENTIRE PROJECT AS SHOWN ON THESE DRAWINGS, INCLUDING ALL NECESSARYFEES AND PERMITS.

2. THE ENTIRE INSTALLATION SHALL CONFORM TO THE MOST RECENTLY ADOPTED REQUIREMENTS OF THEINTERNATIONAL MECHANICAL CODE, INTERNATIONAL PLUMBING CODE, INTERNATIONAL BUILDING CODE, AND ALLOTHER APPLICABLE CITY, COUNTY, AND STATE CODES AND REGULATIONS IN EFFECT AT THE DATEOF THE PERMITTING.

3. PRIOR TO FABRICATION AND INSTALLATION THE CONTRACTOR SHALL COORDINATE THE INSTALLATION OF ALLPLUMBING PIPING, DUCTWORK, AND EQUIPMENT WITH PLUMBING PIPING, PLUMBING EQUIPMENT, ALLDUCTWORK, AND ALL OTHER TRADES INCLUDING BUT NOT LIMITED TO THE MECHANICAL CONTRACTOR,ELECTRICAL CONTRACTOR, GENERAL CONTRACTOR, AND ANY CONTRACTOR HIRED DIRECTLY BY THE OWNER.WHERE CONFLICTS MAY OCCUR, THEY SHALL BE RESOLVED PRIOR TO INSTALLATION.

4. THE DRAWINGS SHOW THE GENERAL DESIGN, ARRANGEMENTS AND THE EXTENT OF THE SYSTEM. ITSHALL BE THE WORK OF THE CONTRACTOR TO MAKE SUCH SLIGHT ALTERATIONS AS MAY BE NECESSARY TOMAKE THE SYSTEM COMPLETE AND OPERATIONAL IN ACCORDANCE WITH THE DESIGN INTENT. MAJORDEVIATIONS SUCH AS CHANGES IN COMPONENT SIZES, WEIGHTS, QUANTITIES, OR MATERIAL REQUIRE PRIORAPPROVAL BY THE CONSULTING ENGINEER.

5. ALL PLUMBING INFORMATION IS NOT SHOWN ON THE PLUMBING DRAWINGS. THE CONTRACTOR SHALL BERESPONSIBLE FOR COORDINATING INFORMATION ON ALL OTHER CONSTRUCTION DOCUMENTS INCLUDINGARCHITECTURAL, STRUCTURAL, MECHANICAL AND ELECTRICAL DRAWINGS.

6. THE WORKING DRAWINGS ARE DIAGRAMMATIC. BECAUSE OF THE SMALL SCALE OF THE DRAWINGS, THEYDO NOT SHOW EVERY OFFSET, BEND OR ELBOW NECESSARY FOR THE COMPLETE INSTALLATION IN THESPACE PROVIDED. ALL LOCATIONS FOR PLUMBING EQUIPMENT AND PIPING SHALL BE CHECKED ANDCOORDINATED WITH THE ARCHITECTURAL, MECHANICAL, STRUCTURAL AND ELECTRICAL DRAWINGS.

7. EXACT ROUTING OF WASTE, GAS, AND WATER SERVICE IS DEPENDENT ON LOCAL SITE CONDITIONS ANDMODIFICATIONS IN EQUIPMENT CONNECTIONS. EXACT LOCATION OF EQUIPMENT MAY VARY DEPENDING ONLOCAL CODE, HEALTH DEPARTMENT AND CITY REQUIREMENTS.

8. DETAILS: THE CONTRACTOR IS RESPONSIBLE TO REVIEW AND USE WHERE APPROPRIATE ALL OF THEPLUMBING DETAILS SHOWN ON THE DRAWINGS. DETAILS MAY OR MAY NOT BE CALLED OUT ON THEDRAWINGS WITH SYMBOLS OR KEYED NOTES. ANY CHANGES RESULTING FROM FAILURE TO INSTALL THEPLUMBING SYSTEM WITHOUT USING THE INCLUDED DETAILS IS THE RESPONSIBILITY OF THE CONTRACTOR.

9. THE DRAWINGS AND SPECIFICATIONS HAVE BEEN PREPARED TO SUPPLEMENT EACH OTHER AND THEY SHALLBE INTERPRETED AS AN INTEGRAL UNIT WITH THE ITEMS SHOWN ON ONE AND NOT THE OTHER BEINGFURNISHED AND INSTALLED AS THOUGH SHOWN AND CALLED OUT IN BOTH.

10. PREPARE 6 COPIES OF SUBMITTALS IN AN INDEXED, LABELED FOLDER CONTAINING FULL PERFORMANCE,MATERIAL AND INSTALLATION INFORMATION ABOUT ALL EQUIPMENT, PIPING, COMPONENTS AND ACCESSORIESTO BE USED.

11. THE STRUCTURE SHOWN ON ALL DETAILS MAY OR MAY NOT PERTAIN TO A PORTION OR ANY PORTIONOF THE BUILDING. COORDINATE MOUNTING REQUIREMENTS WITH ARCHITECTURAL AND STRUCTURAL DRAWINGS.

12. ANY PART OF THIS INSTALLATION THAT FAILS, IS UNFIT, OR BECOMES DAMAGED DURING CONSTRUCTIONSHALL BE REPAIRED OR REPLACED BY THE CONTRACTOR AT NO ADDITIONAL COST TO THE OWNER.

13. ALL EQUIPMENT SHALL PROVIDE THE SCHEDULED PERFORMANCE AT THE SITE ALTITUDE.

14. ALL EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE EQUIPMENT MANUFACTURER'SRECOMMENDATIONS. PROVIDE ALL FITTINGS, TRANSITIONS, VALVES, AND OTHER DEVICES AND ACCESSORIESREQUIRED FOR A COMPLETE, WORKABLE INSTALLATION.

15. ALL MOTORS REQUIRED SHALL BE BY THE DIVISION 15 CONTRACTOR. ALL MOTOR STARTING EQUIPMENT,IF NOT A PART OF THE EQUIPMENT, IS FURNISHED BY THE ELECTRICAL CONTRACTOR.

16. THE CONTRACTOR IS RESPONSIBLE FOR PLUMBING EQUIPMENT CHECK-IN, SAFEKEEPING, AND DAMAGE.

17. INVERTS SHOWN ON PLUMBING DRAWINGS MAY BE REFERENCED FROM THE FINISHED FLOOR ELEVATION.COORDINATE ALL INVERTS WITH CIVIL DRAWINGS PRIOR TO INSTALLATION.

18. PROVIDE WALL CLEANOUTS IN ALL VENTS FOR COMBINATION WASTE AND VENT SYSTEMS AS REQUIRED BYLOCAL AND NATIONAL CODES.

19. ALL VENT FITTINGS FOR WASTE SYSTEMS BELOW OVERFLOWS OF FIXTURES SHALL BE DRAINAGE TYPE.

20. CONTRACTOR TO COMPLY WITH THE LATEST ADOPTED IPC WHEN SIZING TRAP ARMS ON COMBINATIONWASTE AND VENT SYSTEMS. THE DRAWINGS INDICATE THE WASTE LINE SIZE AND THE SIZE OF THE TRAPREQUIRED.

21. PROVIDE CLEANOUTS IN ACCORDANCE WITH THE REQUIREMENTS OF APPLICABLE CODES. FLOORCLEANOUTS SHALL BE LOCATED OUT OF TRAFFIC AREAS.

22. LOCATE ALL PLUMBING VENTS AT LEAST 3 FEET ABOVE OR 10 FEET AWAY FROM ALL OUTSIDE AIRINTAKES INTO THE BUILDING.

23. SEE "PLUMBING FIXTURE SCHEDULE" FOR FIXTURE MAKE AND TYPE, AND SIZE OF INDIVIDUAL WASTE,VENT, AND DOMESTIC WATER PIPING TO FIXTURES.

24. ALL PLUMBING EQUIPMENT SHALL BE LISTED AND LABELED BY AN APPROVED TESTING AGENCY.

25. EQUIPMENT AND INSTALLATION SHALL MEET NATIONAL SANITATION FOUNDATION (NSF) STANDARDS, OREQUIVALENT.

26. PROVIDE PROPER PROVISIONS FOR EXPANSION OR MOVEMENT OF ALL PIPING.

27. ALL PIPE SHALL BE SECURED BY DOUBLE NUTTING AT THE HANGER ROD ATTACHMENT TO THESTRUCTURE, AND AT THE PIPE HANGER.

28. PROVIDE WATER HAMMER ARRESTORS (SHOCK ABSORBERS) AT ALL PIPE LOCATIONS WHERE VALVECLOSURES (SUCH AS FLUSH VALVES) MAY CAUSE WATER HAMMER OR RESULT IN EXCESSIVE PIPE VIBRATIONOR MOVEMENT.

29. PROPERLY LUBRICATE ALL PIECES OF EQUIPMENT BEFORE TURNING THE SYSTEM OVER TO THE OWNER.

30. TWO OPERATING AND MAINTENANCE MANUALS SHALL BE PROVIDED IN HARD BACK LOOSE LEAF BINDERS.MANUALS SHALL CONTAIN PRODUCT CUT SHEETS AND OPERATING AND MAINTENANCE INSTRUCTIONS ON ALLEQUIPMENT, ACCESSORIES, FIXTURES, VALVES, ETC., PROVIDED FOR THE PROJECT.

31. UPON COMPLETION OF THE WORK, REMOVE ALL SURPLUS MATERIALS AND RUBBISH. MAKE ALLREQUIRED PATCHING AND REPAIRS OF OTHER TRADES' WORK DAMAGED BY THIS CONTRACTOR, AND LEAVETHE PREMISES IN A CLEAN, ORDERLY CONDITION.

32. THE CONTRACTOR SHALL OPERATE THE SYSTEM AND DEMONSTRATE ALL ASPECTS TO THE ENGINEERAND/OR OWNER, TO PROVE ITS OPERATION.

33. THE CONTRACTOR SHALL GUARANTEE THE PLUMBING SYSTEM FOR A PERIOD OF ONE YEAR FROM THEDATE OF SUBSTANTIAL COMPLETION.

34. THE CONTRACTOR SHALL, DURING CONSTRUCTION, MAINTAIN A SET OF AS-BUILT REDLINED RECORDDRAWINGS AT THE PROJECT SITE. ALL CHANGES IN LAYOUT, ROUTING, EQUIPMENT, COMPONENTS, ANDACCESSORIES SHALL BE RECORDED. THESE REDLINES SHALL BE GIVEN TO THE ARCHITECT/ENGINEER AFTERTHE FINAL INSPECTION.

SHUT OFF (BALL VALVE TYPE)

PRESSURE REDUCING VALVE (GAS OR WATER)

LIQUEFIED PETROLEUM GASLP

PLUMBING LEGEND

POINT OF CONNECTION

KEYED NOTE CALLOUT

POINT OF DEMOLITION

FIXTURE CALLOUT

SECTION CALLOUT

SECTION

SHEET #

FLOOR DRAIN

FLOOR SINK

ROOF DRAIN

OVERFLOW ROOF DRAIN

BOTTOM CONNECTION

TOP CONNECTION

CAP OR PLUG

PIPE BREAK

DIRECTION OF FLOW

DIRECTION OF PIPE SLOPE

HW POTABLE HOT WATER PIPE

POTABLE COLD WATER PIPE

SS SANITARY SEWER PIPE

POTABLE HOT WATER RETURN PIPEHWR

GREASE WASTE LINE ABOVE GRADE

GREASE WASTE LINE

VTRVTR

ORD OVERFLOW ROOF DRAIN LINE

ROOF DRAIN LINE

VENT THROUGH THE ROOF

VENT LINE

SANITARY SEWER PIPE BELOW GRADESS

G NATURAL GAS LINE

ROOF DRAIN LINE BELOW GRADE

FIRE SPRINKLER RISER

HAMMER ARRESTOR

FIRE DEPARTMENT CONNECTION

HOSE BIBB WITH SHUT OFF

TRAP PRIMER

TWO WAY CLEAN OUT TO GRADE2-WAY COTG

FLOOR CLEANOUT

WALL CLEANOUT

EXPOSED CLEANOUT

COTG CLEANOUT TO GRADE

PLUMBING FIXTURE SCHEDULE

SYMBOL

WATER CLOSET 1" ---

FIXTUREWATER

COLDWATER

4" 2" FLOOR MOUNTED, FLUSH VALVE

VENTACCESSORIESAND REMARKS

FLOOR MOUNTED, FLUSH VALVE2"4"---1"WATER CLOSET (ADA COMPLIANT)WC-2 INT.

2"3"---U-1 INT.

2"3"---U-2 INT.

1-1/2"S-1 SINK - SINGLE COMPARTMENT 1/2" 1/2" 1-1/2" 1-1/2" COUNTER MOUNTED SINGLE COMPARTMENT

3"SS-1 SERVICE SINK 1/2" 1/2" 3" 2" FLOOR MOUNTED WITH DEEP SEAL TRAP

DF-2 WATER COOLER (BI-LEVEL ADA COMPLIANT) 1-1/2"1-1/2"1/2" 1-1/2"

2"FD-2 FLOOR DRAIN --- --- 2" 2" WITH DEEP SEAL TRAP

--- ELECTRIC WATER COOLER, WALL HUNG, BI-LEVEL, 8 GPH, ADA COMPLIANT

FREEZELESS---------3/4"HOSE BIBB (ENCASED) ---

---WATER HAMMER ARRESTOR 1" --- --- --- 33-60 FIXTURE UNITSHA-1

---IM-1 ICE MAKER CONNECTION 1/2" --- --- ---

WITH DEEP SEAL TRAP2"2"------FLOOR SINKFS-2 2"

COTG2-WAY

PIPE RISE

PIPE DROP

ENLARGED PLUMBING

DETAIL CALLOUTDETAIL #

SHEET #

EQUIPMENT CALLOUT

BACK FLOW PREVENTER

3"FD-3 FLOOR DRAIN --- --- 3" 2" WITH DEEP SEAL TRAP

1-1/4"L-6 LAVATORY (ADA COMPLIANT) 1/2" 1/2" 1-1/4" 1-1/4" WALL MOUNTED, ADA COMPLIANT

PROVIDE WATTS LFUSG-B THERMOSTATIC TEMPERING VALVE UNDER COUNTER TO EACH LAV.

ELECTRIC WATER COOLER, WALL HUNG, 8 GPH, ADA WHEELCHAIR1-1/2"1-1/2"---1/2"WATER COOLER (ADA WHEELCHAIR)DF-1 1-1/2"

---HA-1/2 WATER HAMMER ARRESTOR 1/2" --- --- --- 1-11 FIXTURE UNITS

1-1/2"S-2 SINK - TWO COMPARTMENT 1/2" 1/2" 1-1/2" 1-1/2" COUNTER MOUNTED, DOUBLE COMPARTMENTPSI25.0

PSI25.0

PSI20.9

PSI12.0

PSI6.4

65 PSI

BUILDING WATER SUPPLY CALCULATIONSTOTAL FIXTURE UNITS:

ESTIMATED DEMAND:

IRRIGATION DEMAND:

HVAC DEMAND:

TOTAL DEMAND:PRESSURE AVAILABLE AT STREET MAIN:

PRESSURE LOSS DUE TO HEIGHT ( FT. x 0.434):

PRESSURE LOSS THROUGH METER:

PRESSURE LOSS THROUGH OTHER DEVICES:(i.e. Water Softener, Filters, Backflow Preventer)

TOTAL PRESSURE LOSS (Add lines 2 thru 4):

PRESSURE REQUIRED AT HIGHEST FIXTURE:

PRESSURE AVAILABLE FOR FRICTION LOSS:(Subtract lines 5 & 6 from line 1)

HORIZONTAL PIPE LENGTH:

VERTICAL PIPE LENGTH:

EQUIVALENT FITTING LENGTH:

TOTAL DEVELOPED LENGTH:

FRICTION LOSS CALCULATION:(Line 7 / Line 11) x 100

DOMESTIC WATER SERVICE SIZE:

WATER METER SIZE:

BUILDING SEWER SIZE:

10.11.

WATER SUPPLY:WASTE: 187

(/100 FT)4.4

2 1/2"DIA.

DIA.2"

DIA.6"

SPECIFICATIONSECTION 224000,

221119, 221319, 221423

RECIRCULATION PUMP

---TS --- --- ------ JAY R SMITH QUAD CLOSE TRAP SEALTRAP SEAL

---WATER HAMMER ARRESTOR 3/4' --- --- --- 12-32 FIXTURE UNITSHA-3/4

3/4" ---HOSE BIBB (ENCASED) --- --- --- FREEZE PROOF POST HYDRANT, ROOF MOUNTEDHB-2

URINAL (WATERLESS, ADA COMPLIANT) WATERLESS, WALL HUNG

URINAL (WATERLESS) WATERLESS, WALL HUNG

INT.WC-3 WATER CLOSET (CHILDS' 10" HIGH) 1" --- 4" 2" FLOOR MOUNTED, FLUSH VALVE

WH-2 BRADFORD WHITE E32-80R-5 STORAGE 86080 74 18 208/3/60 40° - 140° 24"Ø x 59" 5 GALLON EXPANSION TANK

ELECTRIC WATER HEATER SCHEDULE

(GAL.)CAPACITYSTORAGE

SYMBOL

BRADFORD WHITE E32-120R-5 STORAGE

(LBS.)WEIGHT

OPERATINGINPUTRECOVERYCAPACITY

119 74

RATE(GPH)

VOLTS/Ø/HZ.

208/3/60

40° - 140°

IN/OUTTEMP.

28.25"Ø x 63"

SIZEOVERALL

10 GALLON EXPANSION TANK

MANUFACTURERAND MODEL NO.

ACCESSORIESAND REMARKS

SPECIFICATIONSECTION223300

SCALE: 1/4" = 1' - 0"

BALANCING VALVES

TEMPERING VALVE

G IS C

LASSIFIE

LISHED

THE 1978

ACT, IT IS A

.NONE O

TECHNIC

SHEET M

EANS W

ITHOUT T

RESS P

RITTEN

RCHITECT.

N IS P

LOCATIO

SHEET T

ISSUE: P

SHEET NUMBER:

ISTA, AZ

41 2 3 5 6

L COOK

CHITECT│

EN, UT

7137│

ISTA, AR

IZONA 8

PRELIMINARY D

RAWING!

UCTION!

FOR CONTINUATION OF WATER SERVICE PIPING SEESITE PLAN.

FOR CONTINUATION OF WASTE LINE SEE SITE PLAN.

FIRE SERVICE, FOR CONTINUATION SEE SITE PLAN.

FIRE DEPARTMENT CONNECTION.

FOR CONTINUATION OF PIPING SEE PLUMBINGENLARGEMENTS, SHEET P401.

RISE 3/4" LINE TO ROOF FOR HOSE BIBB.

RUN PIPING ABOVE CEILING.

KEYED NOTES

NOTE:FOR BRANCH SIZES TO INDIVIDUAL FIXTURES NOTSHOWN ON PLANS, SEE PLUMBING FIXTURESCHEDULE, SHEET P001.

10P401

11P401

12P401

CHAPEL101

FOYER102

CATERING103

USHER104

VESTIBULE106

PLAY ROOM107

CLASSROOM A108

R.R.109

CLASSROOM B110

R.R.111

CLASSROOM C112

CRAWLERS113

CHECK-IN114 R.R.

INFANTS116

OFFICE117

MEN'S118

JAN.119

CORRIDOR120

stg.121

R.R.122

STG.123

TACTILE124

MOTOR SKILLS125

SENSORY126

MINISTRY127

COUNS.128

FAM. R.R.129

BACKSTAGE/STORAGE130

MASTER CONTROL131

BACK STAGE132

RACK ROOM133

GREEN ROOM134

R.R.135

MAN CAVE136

R.R.137

COUNS.138

BRIDE'S ROOM139

CORRIDOR140

JAN.141

WOMEN'S142

SPRK.143

STORAGE144

HOSPITALITY145

SANCTUARY147

PLATFORM148

CAFE150

san.149

MDP143.1

CHANGING146.1

3 9 10 1211

4 8 13

6.1 6.9

FD-3TS

INVERT ELEVATION XXX.X'INVERT ELEVATION XXX.X'

1 1/4"

1 1/2"

2" VTR

1 1/4"

2 1/2"

2 1/2"2 1/2"

1 1/4"

3RD PLACE105

BAPTISTRY146

1 PLUMBING FLOOR PLANSCALE: 1/8" = 1'-0"

ROOF P

G IS C

LASSIFIE

LISHED

THE 1978

ACT, IT IS A

.NONE O

TECHNIC

SHEET M

EANS W

ITHOUT T

RESS P

RITTEN

RCHITECT.

N IS P

LOCATIO

SHEET T

ISSUE: P

SHEET NUMBER:

ISTA, AZ

41 2 3 5 6

L COOK

CHITECT│

EN, UT

7137│

ISTA, AR

IZONA 8

PRELIMINARY D

RAWING!

UCTION!

PROVIDE P-TRAP A CONDENSATE DRAIN AND SPILLTO ROOF.

KEYED NOTES

RTU5RTU

3 9 10 1211

4 8 13

6.1 6.9

2" VTR

1 1/2" VTR

2" VTR2" VTR

2" VTR

4" VTR

1 1/2" VTR

4" VTR

1 PLUMBING ROOF PLANSCALE: 1/8" = 1'-0"

G IS C

LASSIFIE

LISHED

THE 1978

ACT, IT IS A

.NONE O

TECHNIC

SHEET M

EANS W

ITHOUT T

RESS P

RITTEN

RCHITECT.

N IS P

LOCATIO

SHEET T

ISSUE: P

SHEET NUMBER:

ISTA, AZ

41 2 3 5 6

L COOK

CHITECT│

EN, UT

7137│

ISTA, AR

IZONA 8

PRELIMINARY D

RAWING!

UCTION!

FOR CONTINUATION OF PIPING SEE PLUMBING FLOORPLAN, SHEET P101.

FIXTURE PROVIDE BY KITCHEN EQUIPMENT SUPPLIER.PLUMBING CONTRACTOR TO PROVIDE STOPS, SUPPLIES,TRAPS, ETC. AND MAKE FINAL CONNECTIONS.

DROP 3/4" CW LINE TO COMBI OVENS. PROVIDE SHUT-OFF VALVE, BACKFLOW PREVENTER AND HOSECONNECTION.

KEYED NOTES

R.R.109

FD-2TS

1 1/4"

1/2"1/2"

2" VTR

1 1/2"

1 1/4"

S-1R.R.111

FD-2TS

1 1/4" 1 1/4"

2" VTR

1 1/2"

1 1/4"

san.149

1 1/2" VTR

WC-3S-1

R.R.115

FD-2TS

2" VTR

1 1/2"

2"1 1/4"

1 1/2"

1 1/4"

MEN'S118

JAN.119

FD-2TS

1 1/2"

FD-2TS

1 1/4"

1 1/2"

4" VTR

2 1/2"

1 1/4"

1 1/4"1 1/2"

R.R.122

FD-2TS

2" VTR

1 1/4"

FAM. R.R.129

FD-2TS

2" VTR

1 1/4"

L-6 WC-2 S-1

R.R.135

FD-2TS

1/2"1/2"

2" VTR

1 1/4"1 1/2"

1 1/4"

3/4" 1

R.R.137

FD-2TS4"

2"2" VTR

1 1/4" 1 1/4"

CORRIDOR140

JAN.141

WOMEN'S142

FD-2TS

3"1" 1 1/2" VTR3"

1 1/4"

4" VTR

2 1/2"

HB-1 3/4"

1 1/4"1 1/4"

2"1 1/4"

1 1/4"

1 1/4"2"

1 1/4"

CATERING103

HOSPITALITY

CAFE150

2" VTR

CHANGING146.1

6.1 6.9

3/4"3"

BAPTISTRY146

4 ENLARGED PLUMBING PLANSCALE: 1/4" = 1'-0" 5 ENLARGED PLUMBING PLAN

SCALE: 1/4" = 1'-0" 6 ENLARGED PLUMBING PLANSCALE: 1/4" = 1'-0" 7 ENLARGED PLUMBING PLAN

SCALE: 1/4" = 1'-0"

2 ENLARGED PLUMBING PLANSCALE: 1/4" = 1'-0"

SCALE: 1/4" = 1'-0" 11 ENLARGED PLUMBING PLANSCALE: 1/4" = 1'-0"

SCALE: 1/4" = 1'-0"

DETAILS

G IS C

LASSIFIE

LISHED

THE 1978

ACT, IT IS A

.NONE O

TECHNIC

SHEET M

EANS W

ITHOUT T

RESS P

RITTEN

RCHITECT.

N IS P

LOCATIO

SHEET T

ISSUE: P

SHEET NUMBER:

ISTA, AZ

41 2 3 5 6

L COOK

CHITECT│

EN, UT

7137│

ISTA, AR

IZONA 8

PRELIMINARY D

RAWING!

UCTION!

ACCESS FRAME AND COVER TOP OF COVER SHALL BEFLUSH WITH TOP OF FLOOR

COUNTERSUNK SCREW

CAST IRON 1/8BEND

1/8 BEND IF CLEANOUT OCCURS AT END OF LINE

WASTE PIPING

BALANCE OF PIPING SAME ASCLEANOUT TO GRADE

FINISHED FLOOR

BRASS CLEANOUT PLUG AND FERRULE

MAY EXTEND AS A WASTE OR VENT LINE

FINISHED FLOOR

1/8" C.I. BEND

REFERENCED ON DRAWING AS "WCO"

BALANCE OF PIPING SAME AS CLEANOUT TOGRADE

PLUGGED TEE WITHCLEANOUT

CHROME WALL COVER AND SCREW

FINISHED GRADE

18"x18"x6" THICK CONCRETE PAD

C.I. PIPE (SIZE AS SHOWN ONDRAWINGS)

4" C.I. PIPE

CEMENT PATCH

4" C.I.

CLEANOUT PLUG

C.I. COVER AND FRAME

6" MIN.

VARIES

1'-0"1'-0"

6" LAYERS OF SAND, COMPACTABLE SOIL, OR APPROVED GRAVELPLACED AND COMPACTED 95% MIN. DRY DENSITY AASHTO T-180

CONCRETE SLAB

FINISHED FLOOR

CONCRETE (TYP.)

USE CAULKED OUTLET TYPECONNECTION.

DEEP SEAL P-TRAP

WATERPROOF MEMBRANEFLASHED INTO CLAMPING

COLLAR.

ADJUSTABLE HEAD SET FLUSH WITHFINISHED FLOOR

SLOPE SLOPE

2'-0" x 2'-0" BLOCKOUT

TRAFFIC GRATE

FULL GRATE UNLESS OTHERWISE SCHEDULEDOR SPECIFIED

DOME STRAINER

FLOOR SINK OUTLET (2" MINIMUM)

NO HUB CLAMP (TYP.)3" WASTE MINIMUM FOR COMBINATION WASTEAND VENT SYSTEM

2" x 3" REDUCER REQUIRED FOR ALL FLOOR SINKSFOR COMBINATION WASTE AND VENT SYSTEM

DRAIN BODYFLASHING CLAMP

FLOOR LINE

NON TRAFFIC GRATEHANGER ROD

DOUBLE NUT CLEVIS HANGERTO ROD

PIPE INSULATION

RIGID INSULATION AT SUPPORT22 GAUGE SHEET METAL INSULATION

SHIELD - 12" LONG

CARRIER PIPE

CLEVIS HANGER

12" MIN.ROOFING

ROOF DECKVENT

FLASHING

STAINLESS STEEL CLAMPSEALANT

REDUCED PRESSURE BACKFLOW PREVENTOR. PROVIDE INLET AND OUTLET SHUT-OFF VALVES AND 4 TEST COCKS. (MAY BE SUBSTITUTED WITH DOUBLE CHECK

ASSEMBLY IF APPROVED BY LOCAL AUTHORITY HAVING JURISDICTION)

TO POTABLE WATERSYSTEM

GLOBE VALVE

PRESSURE GAGE (TYP)

UNION (TYP)

BALL VALVE (TYP)

PRESSURE REDUCING VALVE TO HANDLE --- GPM @ 65 PSIDISCHARGE PRESSURE

STRAINER WITHBLOWDOWN

INCOMING WATER SERVICE SLEEVE CONCRETE FLOOR

12" MINIMUMABOVE FLOOR

VACUUM RELIEF VALVE

EXPANSION TANKBALL VALVE

COLD WATER SUPPLY

AQUASTATRECIRCULATING HOT WATERLINE AND PUMP

P&T RELIEF VALVE

ANCHOR WATER HEATER TO WALL USE 1" X 18 GA. STRAP WITH#10 X 2 1/2" WOOD SCREWS. TYPICAL OF TWO PLACES.

DRAIN VALVE W/THREADED HOSE CONNECTION

RUN DISCHARGE LINE TO FLOOR DRAIN

DIELECTRIC UNION (TYPICAL)

HOT WATER

THERMOMETER

1 FLOOR CLEANOUTSCALE: N.T.S. 2 WALL CLEANOUT

SCALE: N.T.S. 3 CLEANOUT TO GRADESCALE: N.T.S. 4 PIPE UNDER SLAB

SCALE: N.T.S.

5 FLOOR DRAINSCALE: N.T.S. 6 FLOOR SINK

SCALE: N.T.S.7 INSULATED PIPE HANGER

SCALE: N.T.S.8 VENT THRU ROOF (FLAT)

SCALE: N.T.S.

9 WATER PRESSURE REDUCING VALVE STATIONSCALE: N.T.S. 10 ELECTRIC WATER HEATER DETAIL

SCALE: N.T.S.

GENERAL PLUMBING NOTES -...

Documents

Transcript of GENERAL PLUMBING NOTES -...

Plumbing Fixture Matrix Residence InnResidence · PDF filePlumbing Fixture Matrix Residence InnResidence Inn ... to be used for Marriott CFRST LEED Volume ... Plumbing Fixture Matrix

WE PREREQUISITE 1: MINIMUM INDOOR PLUMBING … · LEED 2009 for Existing Buildings: Operations & Maintenance WE Prerequisite 1: Minimum Indoor Plumbing Fixture and Fitting Efficiency

appendix For Plumbing (d20) - Builder™ Summitbuildersummit.com/uploads/D20 - Plumbing.pdf · • Sanitary Waste ... • Other Plumbing Systems (D2090): Specialty pipe, equipment

Plumbing Fixture Matrix SpringHill SuitesResidence Inn Drawings/22-224000b-S-Plumbing...Plan Mark (Old) Plan Mark Model No. Finish Manufacturer Area Location (New) Plumbing Fixture

EVOLUTIONARY PLUMBING SOLUTIONS · 2018. 4. 20. · plumbing supplies; and Streamlabs™ smart water control technologies. END-TO-END PLUMBING SOLUTION, METER TO FIXTURE, FLOOR TO

PLUMBING FIXTURE SCHEDULE - SJECCD Bldg Wellness Center Addendu… · symbol fixture type description mfr model accessories w v cw hw notes df-1 drinking fountain (electric water

Design Considerations for Hot Water Plumbing Considerations for... · Design Considerations for Hot Water Plumbing ... Hot Water System ... Fixture - A device for the distribution

ELECTRIC WATER HEATER SCHEDULE PLUMBING FIXTURE …rgaarchitects.com/Cloud/Revision-1/Plumbing.pdf · contractor shall furnish and install on each plumbing fixture chrome plated brass

Front2003 - Jackson Fire District No. 3 Plumbing.pdf · FOREWORD Since its founding as the National Association of Master Plumbers in 1883, the National Association of Plumbing-Heating-Cooling

Plumbing Fixture Fittings Trim Brass Goods P34320 M

US Army Plumbing v Repair Valve Fixture Control Devices

Chicago Chapter of the American Society of Plumbing ...Alternate Venting Methods- Venting beyond individual fixture venting; Presented by: George B. Swietc-zak, Plumbing Inspector

Plumbing Fixtures CEU 198 - Welcome to ASPE · PDF fileIt has been said that without plumbing fixtures, there would be no indoor plumbing. Each fixture is designed for a specific function

Modernism, Amodernism and Marcel Duchamp, or why is a urinal no longer just a plumbing fixture?

GROUND FLOOR PLANpnp.gov.ph/images/biddocs/CSG/SOSIA/Plumbing.pdf · of the national plumbing code as vents except otherwise specifically indicated fittings or recess reducers horizontal

22 05 00 - COMMON WORK RESULTS FOR PLUMBING.pdf

Cross Connection Plumbing - MHCEA DOLI - Plumbing.pdf · Cross Connection Plumbing James Peterson Plumbing Program • Phone: (651) 284‐5889 • E‐mail: jim.peterson@state.mn.us

Offering Memorandum - LoopNet€¦ · Walls & Ceilings: Drywall & panel walls, acoustic ceiling Plumbing: (13) 3-fixture baths with fiberglass shower stalls, (2) 2-fixture baths in

Denver Plumbing.pdf

IRC — Plumbing - iccsafe.orgiccsafe.org/wp-content/uploads/IRC-Plumbing.pdf · P2503.5.1 Rough plumbing. DWV systems shall be tested on completion of the rough piping installation