Post on 11-Feb-2022
Research ArticleGearbox Low-Noise Design Method Based onPanel Acoustic Contribution
Jianxing Zhou, Wenlei Sun, and Qing Tao
School of Mechanical Engineering, Xinjiang University, Urumqi 830047, China
Correspondence should be addressed to Jianxing Zhou; jianzhou82923@163.com
Received 15 September 2013; Accepted 28 November 2013; Published 2 January 2014
Academic Editor: Hamid Reza Karimi
Copyright ยฉ 2014 Jianxing Zhou et al. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
This paper presents a comprehensive procedure to calculate steady dynamic response and generated noise radiation from a gearreducer. In this process, the dynamic model of the cylindrical gear transmission system is built in consideration of the time-varying mesh stiffness, gear errors, and bearing supporting, while the data of dynamic bearing force is obtained through solvingthe model. Furthermore, taking the data of bearing force as the excitation, the gearbox vibrations and noise radiation are calculatedby numerical simulation, and then the time history of node dynamic response, noise spectrum, and resonance frequency range ofthe gearbox are obtained. At last, the gearbox panel acoustic contribution at the resonance frequency range is calculated. Accordingto the conclusions of the gearbox panel acoustic contribution analyses and the mode shapes, two gearbox stiffness improving plansis researched. By contrastive analysis of gearbox noise radiation, the effectiveness of the improving plans are verified. The studyprovides useful theoretical guideline to the gearbox design.
1. Introduction
Withmany advantages, that is, high efficiency, tight structure,stable speed ratio, and so forth, gear train has been widelyused in many industrial fields. When the gear reducer isrunning, the gearbox vibration is generated, due to the effectof the gear pair dynamic mesh force, which not only affectsthe stability of the transmission system but also generatesnoise. In addition, excessive noise produced by a reducercauses crew fatigue, strained communication, and possiblehearing damage. In order to ensure a quiet, smooth, andsafe operation of a gear transmission system, it is necessaryto understand mechanisms of the dynamic response andthe noise radiation of the gear reducer; meanwhile, theirreduction is highly desired.
With increasing demand for quieter gear systems, a largeamount of work was reported in the literatures on analyzingthe vibration and noise of the gearbox. Abbes et al. built thegearbox vibroacoustic system by using a three-dimensionalfinite-element (FE) approach, and the acoustic response ofthe system was evaluated [1]. Velex andMaatar computed thedynamic responses to mesh stiffness variations for numericalgears [2]. Their results showed the impact of mesh stiffness
variation on dynamic response and tooth loads. Dion et al.developed an experimental and numerical study of dynamicphenomena involving gear impacts with one loose gear insidean automotive gearbox [3]. Barthod et al. dealt with therattle noise, caused by the fluctuation of the engine torqueunder special conditions, which could causemultiple impactsinside the gearbox [4]. Kato et al. simulated the vibrationand noise radiation of a single-stage gearbox by combiningfinite-element (FE) vibration analysis with boundary elementnoise analysis [5].The results of this analysis were well agreedwith the corresponding measured data. Spur and helicalgears were tested in the NASA gear-noise rig to comparethe noise produced by different gear designs [6]. The usefulconclusions about the effect of the gear design parameterson gearbox radiated noise were got. Choy et al. presentedmethod to predict both the vibration and noise generated by agear transmission system under normal operation conditions[7], and the application of the method is demonstrated bycomparing the numerical and experimental results for thegear noise test rig. Yanyan and Zhen confirmed that the gearpair is the main excitation of the gear reducer and reducedthe gearbox noise through matching the precision gradeand stiffness of the gears [8]. Kahraman and Blankenship
Hindawi Publishing CorporationMathematical Problems in EngineeringVolume 2014, Article ID 850549, 10 pageshttp://dx.doi.org/10.1155/2014/850549
2 Mathematical Problems in Engineering
investigated contact ratio effects experimentally using a back-to-back gearbox rig. The dynamic transmission error (DTE)amplitudes of spur gear pairs with varying contact ratios weremeasured. The measurements were performed for excitationat and around the torsional natural frequency of the gear pair.The gear mesh frequency was used as a form of torsionalexcitation, with the limitation that excitation is dependenton rotational speed [9]. Kostic and Ognjanovic found thatthe noise emission of gear units (gearboxes) depends bothon the disturbances (gear meshing, bearing operation, etc.)and on the insulating capabilities and modal behavior ofthe housing. Natural vibrations of the housing walls can beprevented or intensified depending on design parameters[10]. Tuma reviews practical techniques and proceduresemployed to quiet gearboxes and transmission units [11].With the complexity of the gearbox structure and the gearexcitation, excessive simplification has been made in mostof the previous research; meanwhile no effective method toreducing vibration and noise is found.
In this study, we present a comprehensive procedureto predict the noise radiation of the gear reducer. In theprocedure, the 4-DOF dynamic model is built, and thentaking the bearing force as the excitation, vibrations andnoise radiation of the gearbox are researched. According tothe results of the panel acoustic contribution analysis onthe resonant frequency band of the gearbox and the modeshapes, effective methods to reducing vibration and noise aresuggested.
2. Analysis Procedure of Noise Radiating
Gear errors and fluctuations in mesh stiffness can causeexcitation during gear meshing; this excitation propagatesfrom the gear shafts to the bearing and excites the gearboxand generations reducer noise which is radiated from thesurface of the gearbox. In order to concern about both geartransmission system dynamic characteristics and gearboxdynamic characteristics, an excellent prediction method ofgearbox noise radiation is proposed.
As illustrated in Figure 1, the developed method consistsof three separate steps: dynamic bearing force calculationby solving the gear transmission system dynamic model,gearbox vibration analysis by using finite element method(FEM), and boundary element analysis (BEA) of the soundfield. In thismethod, a commercial software, LMS.Virtual.lab,is used to analyze the sound radiation for the gear reducer.The input data are fundamental performance parametersof the gear reducer, which consist of the gearbox shape,material, gear error, bearing stiffness, and so on. The outputdata are vibrations and noise analysis results, which consistof dynamic responses, frequency spectrum for noise, panelacoustic contribution, and so on. The low-noise gearboxis designed according to the conclusion of panel acousticcontribution and gearbox dynamic characteristics.
3. Gearbox Excitation Calculation
In a power transmission gear system, the gear pair assemblyremains one of the major noise and vibration sources in
Table 1: The gear system parameters.
Power(Kw)
Gearratio
Module(mm)
Pressureangle (deg)
Face width(mm)
Rotationalspeed (r/min)
10 20/80 3.0 20 60 1000
the system. The vibrations of the gear transmission systemare generated due to the fluctuation of the dynamic meshingforce, which is affected by the time-varyingmesh stiffness anderrors.
3.1. Gear Time-Varying Mesh Stiffness. The gear system pa-rameters are given in Table 1. The variation of the mesh stiff-ness for the gear pair is obtained by using static finite elementanalysis, in which FEM Contact Algorithm is adopted.
The FE-model of the gear pair and boundary conditions isshown in Figure 2. During the calculation of the time-varyingmesh stiffness, the driven gear is fixed, the torque๐ is appliedon the driving gear, and contact constraint is applied betweenthe engaged tooth of the driving gear and the driven gear.
As a result of the toothHertzian contact deformations andtooth bending deformations, the driving gear will revolved asmall angle ๐ on its centre. The small angle ๐ is obtained bysolving the gear pair FE-model; then the total deformation ofthe meshing line is defined as
๐ข = ๐ โ ๐ ๐, (1)
where ๐ ๐ is the base radius of the driving gear.So the mesh stiffness at this position is represented by the
equation
๐พ =๐
(๐ ๐๐ข), (2)
where ๐ is the torque.Since the gear rotation is continuous, the gear meshing
stiffness is periodic at the mesh frequency, a complete meshcycle is divided into several steps, and the rotatory angleand position of the gears at every step can be calculatedaccording to gear mesh theory. Then the calculation of themesh stiffness is repeated at every gear engaging position.The time-varying mesh stiffness function is formed by cubicspline interpolation, as shown in Figure 3(a). As the numberof tooth pairs in contact changes, abrupt changes in the gearpair stiffness occur (the mesh of spur gears with two toothpairs in contact is roughly twice as stiff as when one toothpair is in contact).
3.2. Gear Errors. Vibrations of gear pairs are largely affectedby the amplitude and phase of deviations of the toothprofile from the true involute one, which is induced by gearmanufacturing and installing errors. Meanwhile, with theeffect of the gear errors on the instantaneous contact ratio,the collision and impact occur while the gear pair is running[12]. As a result, gear errors must be included in the geartransmission system model. Generally, the deviations areassumed to be small enough so that tooth contacts remain on
Mathematical Problems in Engineering 3
Meshstiffness
Bearingstiffness
Gearerror
Gearboxmaterial
Four-DOF gear systems dynamics
Gearboxmodel
FEM modal analysis
Gearbox vibration analysis by FEM
Gearbox vibration frequency responsesu(t)
Gearbox noise radiation analysis by BEM
Gearbox noise radiation frequency responses
Output
Input
Gearbox resonance frequency bands
Gearbox panel acoustic contribution
Dynamic bearing load F(t)
Redu
cer i
mpr
ovem
ent
Figure 1: Analysis procedure of gear reducer noise radiation.
Driven gear
Contact
Fixed
Driving gear
T
Figure 2: Gear pair finite element model.
the theoretical line of action [2]. Error function, representingthe sum of pitch, profile, pressure angle, and run out errors, issupposed as displacement excitations along the tooth profileas a sine wave in the model. The harmonic function isused to simulate the gear error variation which is shown inFigure 3(b). The error function is written as
๐ (๐ก) = ๐๐ sin(๐ค๐ก
๐๐
+ ๐) , (3)
where ๐๐ is error amplitude, ๐๐ is the mesh cycle, ๐ค is theangular velocity of the driving gear, and ๐ is the phase angle.
3.3. Gear Transmission Systems Dynamics Model. The pro-posed dynamic model of the gear pair is shown in Figure 4,which represents the driving gear (subscript ๐) meshing withdriven gear (subscript ๐). The following assumptions aremade in the model formulation.
(a) The deflection of the shaft is neglected, because thespan of the bearings is little.
(b) Shaft mass and inertia are lumped at the gears.(c) The bodies representing the two gear bodies are
assumed to be rigid disks [13].(d) The gear-shaft connections were assumed to be rigid,
ignoring the stiffness of the connections and anyconsequent relative torsional motion between theshaft and gear hub.
(e) Gear pairs mesh flexibility and other parts flexibilityare included in the form of a linear spring. The gearmesh stiffness is time variant; the support stiffness isconstant.
Namely,๐พ๐๐ฆ and๐พ๐๐ฆ denote bearing stiffness of the driv-ing gear and driven gear and ๐พ๐ denotes time-varying meshstiffness. The angular displacements ๐๐ and ๐๐ of the drivinggear and the driven gear are in the reversed direction; in thesame time, the transverse displacements ๐๐ and ๐๐ in thedirection of meshing line are considered.
The angular displacements and the transverse displace-ments of the gears will affect meshing state of the gear
4 Mathematical Problems in Engineering
0 5 10 15 20 25 30 35
6
9
ร 108
12
Mes
h sti
ffnes
sK(N
/m )
Driving gear rotating angle ๐ (โ)
(a) Time-varying mesh stiffness
0.000 0.001 0.002 0.003
โ1.5
0.0
1.5
3.0
Erro
re(๐
m)
Time t (s)
(b) Manufacture error
Figure 3: The transmission system excitation.
pair, so the displacement is transformed to action line. Thedisplacement on the action line is written as
๐ฆ๐= ๐ ๐๐๐ โ ๐ฆ๐, ๐ฆ
๐= ๐ฆ๐ โ ๐ ๐๐๐, (4)
where ๐ ๐ is the base circle radius of the driving gear and ๐ ๐
is the base circle radius of the driven gear.The mesh force and damping force of the gear pairs are
written as
๐น๐ = ๐๐ (๐ฆ๐ + ๐ฆ๐โ ๐) = ๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐) ,
๐น๐ = ๐๐ (๏ฟฝ๏ฟฝ๐ + ๏ฟฝ๏ฟฝ๐โ ๐) = ๐๐ (๐ ๐
๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐) ,
(5)
where ๐ is the gear error, ๐ ๐ is the base circle radius ofthe driving gear, ๐ ๐ is the base circle radius of the drivengear, and ๐๐ is mesh damping coefficient of gear pair ๐๐ =
2๐โ๐๐/(1/๐๐ + 1/๐๐), ๐๐ is the mass of the driving gearand ๐๐ is mass driven gear of the driven gear. The range ofthe damping ratio ๐ is 0.03 โผ 0.1.
Therefore, dynamic mesh force ๐น๐๐ is defined as
๐น๐๐ = ๐น๐ + ๐น๐. (6)
Similarly, supporting spring force (bearing force) is definedas
๐น๐๐ฆ = ๐๐๐ฆ๐ฆ๐, ๐น๐๐ฆ = ๐๐๐ฆ๐ฆ๐. (7)
According to the Newtonmechanics law, the following differ-ential equations of the gear system are set up, which contains
Y
X
p
G
e
mp
kpy
wp
OpRp
cpy
km cm
Og
Rg
wg
kgy cgy
Figure 4: The dynamic model of the system.
the effects of time-varyingmesh stiffness and error excitation.Total number of degree of freedom for the model is 4:
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ + ๐๐๐ฆ๐ฆ๐ = ๐น๐๐,
๐ผ๐๐๐ = ๐๐ โ ๐น๐๐๐ ๐,
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ + ๐๐๐ฆ๐ฆ๐ = โ๐น๐๐,
๐ผ๐๐๐ = ๐๐ โ ๐น๐๐๐ ๐.
(8)
Here, ๐๐ is the input torque. ๐๐ is the load torque. ๐ผ๐ is therotational inertia of driving gear. ๐ผ๐ is the rotational inertia ofdriven gear.
Mathematical Problems in Engineering 5
Equation (6) in conjunction with (8) yields 4 coupledhomogeneous ordinary differential equations in the form
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ + ๐๐๐ฆ๐ฆ๐
= ๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐
๐๐ โ ๐)
+ ๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐) ,
๐ผ๐๐๐ = โ [๐๐ (๐ ๐
๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐)
+๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐)] ๐ ๐ + ๐๐,
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ + ๐๐๐ฆ๐ฆ๐
= โ๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐
๐๐ โ ๐)
โ ๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐) ,
๐ผ๐๐๐ = [๐๐ (๐ ๐
๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐)
+๐๐ (๐ ๐๐๐ โ ๐ฆ๐ + ๐ฆ๐ โ ๐ ๐๐๐ โ ๐)] ๐ ๐ + ๐๐.
(9)
In the mathematical model, the angular displacements๐๐ and ๐๐ are independent variables. In order to solve theequations, the angular displacements should be transformedinto an independent variable.Therefore, transmission error islead into the model, defined ๐ฆ๐๐ = ๐ ๐๐๐ โ ๐ ๐๐๐; then rigidbody displacement is removed; the model can be written as
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ โ ๐๐ ( ๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐) + ๐๐๐ฆ๐ฆ๐
โ ๐๐ (๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐) = โ๐๐ ๐ โ ๐๐๐,
๐๐ ๐ฆ๐ + ๐๐๐ฆ ๐ฆ๐ + ๐๐ ( ๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐) + ๐๐๐ฆ๐ฆ๐
+ ๐๐ (๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐) = ๐๐ ๐ + ๐๐๐,
๐๐๐ ๐ฆ๐๐ + ๐๐ ( ๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐) + ๐๐ (๐ฆ๐๐ โ ๐ฆ๐ + ๐ฆ๐)
= ๐๐ ๐ + ๐๐๐ โ
๐น๐๐๐๐
๐๐
+
๐น๐๐๐๐
๐๐
,
(10)
where ๐๐๐ is equivalent mass of the gear pair, ๐๐๐ = ๐๐๐๐/
(๐๐ + ๐๐), ๐๐ = ๐ผ๐/๐ 2
๐, ๐๐ = ๐ผ๐/๐
2
๐, ๐น๐ = ๐๐/๐ ๐, and ๐น๐ =
๐๐/๐ ๐.The equation of motion is given in the matrix form as
[๐] {๏ฟฝ๏ฟฝ} + [๐ถ] {๏ฟฝ๏ฟฝ} + ๐พ (๐ก) {๐} = {๐ (๐ก)} , (11)
where๐ is the mass matrix, ๐ถ is the damping matrix,๐พ(๐ก) isthe stiffness matrix, ๐ is the vector of the displacement, and๐(๐ก) is the vector of the load. The mass matrix, the damping
matrix, the stiffness matrix, and load vector are given,respectively, as
[๐] = [
[
๐๐
0
๐๐
0
๐๐๐
]
]
,
[๐ถ] =
[[[[
[
๐๐๐ฆ + ๐๐ โ๐๐ โ๐๐
โ๐๐ ๐๐๐ฆ + ๐๐ ๐๐
๐๐ โ๐๐ โ๐๐
]]]]
]
,
[๐พ] =
[[[[
[
๐๐๐ฆ + ๐๐ โ๐๐ โ๐๐
โ๐๐ ๐๐๐ฆ + ๐๐ ๐๐
๐๐ โ๐๐ โ๐๐
]]]]
]
,
{๐} =
{{{{{
{{{{{
{
โ๐๐ ๐ โ ๐๐๐
๐๐ ๐ + ๐๐๐
โ๐๐ ๐ โ ๐๐๐ +
๐น๐๐๐๐
๐๐
โ
๐น๐๐๐๐
๐๐
}}}}}
}}}}}
}
.
(12)
3.4. Dynamic Bearing Force. Equation (11) is solved byusing the Newmark time integration method. The Newmarkmethod is a generalization of the linear acceleration method[14]. This latter method assumes that the acceleration varieslinearly within the interval (๐ก + ฮ๐ก). This give
{๏ฟฝ๏ฟฝ๐} = {๏ฟฝ๏ฟฝ๐ก} +1
ฮ๐ก({๏ฟฝ๏ฟฝ๐ก+ฮ๐ก} โ {๏ฟฝ๏ฟฝ๐ก}) ,
{๏ฟฝ๏ฟฝ๐ก+ฮ๐ก} = {๏ฟฝ๏ฟฝ๐ก} + [(1 โ ๐ฟ) {๏ฟฝ๏ฟฝ๐ก} + ๐ฟ {๐ฅ๐ก+ฮ๐ก}] ฮ๐ก,
{๐ฅ๐ก+ฮ๐ก} = {๐ฅ๐ก} + {๏ฟฝ๏ฟฝ๐ก} ฮ๐ก + [(1
2โ ๐ฝ) {๏ฟฝ๏ฟฝ๐ก} + ๐ฝ {๐ฅ๐ก+ฮ๐ก}] ฮ๐ก
2.
(13)
The response at time ๐ก + ฮ๐ก is obtained by evaluating theequation of motion at time ๐ก + ฮ๐ก. The Newmark method is,therefore, an implicit method.
TheNewmark method is unconditionally stable provided
๐ฟ โฅ 0.5, ๐ฝ โฅ1
4(๐ฟ + 0.5)
2. (14)
One can find that ๐ฟ โฅ 0.5 and ๐ฝ = 0.5 lead to acceptableresults for most of problems, ๐ฟ โฅ 0.5 and ๐ฝ = 0.5 are alwaysused in this paper for simplification.
The dynamic bearing force is shown in Figure 5. Dynamicbearing force presents periodic fluctuations and the majorcomponents at 4 times, 5 times, and 6 times the meshfrequency (333Hz).
4. Analysis of Gearbox Vibration andNoise Radiaton
4.1. Gearbox FE-Model. The gear reducer model is shown inFigure 6. In order to predict the noise of the transmissionsystem during operation, vibration of the gearbox must
6 Mathematical Problems in Engineering
Time (s)
Bear
ing
forc
e (N
)
0.000 0.015 0.030 0.045 0.060
โ3440
โ3360
โ3280
โ3200
(a) The time history of dynamic pinion bearing force
204060
Frequency (Hz)
Am
plitu
de (N
)
Mesh frequency
0 500 1000 1500 2000 2500
3ร4ร
5ร
6ร
(b) Frequency spectra of dynamic pinion bearing force
3300336034203480
Time (s)
Bear
ing
forc
e (N
)
0.000 0.015 0.030 0.045 0.060
(c) The time history of dynamic wheel bearing force
0
25
50
Frequency (Hz)
Am
plitu
de (N
)
3ร
4ร
0 500 1000 1500 2000 2500 3000
(d) Frequency spectra of dynamic wheel bearing force
Figure 5: The dynamic bearing force.
be accurately computed. The finite element model of therealistic character gearbox is built up by using the commercialsoftware ANSYS and shown in Figure 7.Themodel consistedof 146238 elements and 38634 nodes. The material of thegearbox is cast steel, whose elastic modulus ๐ธ = 207GPa,Poisson ratio ๐ = 0.3, and density ๐ = 7800Kg/m3. Thebolt holes in the bottom of the gearbox are fixed, due to thegearbox connected with the base through the holes. For theconvenience of dynamic load applying, a node is created inthe center of the bearing bore; then the center node is coupledwith the node on the inside surface of the bearing bore andthe dynamic load is applied.
4.2. Gearbox Vibration Modal Analysis. The Lanczos methodis used in the modal analysis of the gearbox. Eight modesin the frequency range 0 to 3000Hz, shown in Figure 8,are chosen to represent the vibration of the gearbox. Thevibration of the bottom half gearbox is not as intense as theupper half, because there are bolt constraints and the supportof the stiffeners on the bottom of the gearbox.
4.3. Studies of Gearbox Dynamic Response. During the pro-cess of dynamic response solution, the dynamic load which
310
370
190
Figure 6: The gear box three-dimensional model.
X YZ
Center node
Z
X
Sample node
Fixed
Sound field R = 1m
Figure 7: The gear box FE-model.
is acted on the bearing should be transformed into discreteimpact load; then structure response is computed under theimpact load step by step, until it achieves steady state.
For the modal superposition method is used in thedynamic response calculation; all the modes which are influ-ential to dynamic response should be calculated; otherwisethe result will not be accurate due to the absence of modes.Nearly 200 vibrational modes are used in the calculation; themaximum natural frequency is 20000Hz.
Figure 9 is the time domain dynamic response signal andcorresponding frequency spectra of the signal for the node onthe gearbox top surface. Figure 9(a) shows the node dynamicresponse (displacement) at operating speed of 1000 rpm.Notethat the largest amplitude of the response is 1.6 ๐m.
Figure 9(b) shows the frequency components of the res-ponse. The major vibration components occur at 3 times, 4times, and 5 times the mesh frequency (333Hz). The verylarge amplitude in the frequency components at the range of1550Hz โผ 1700Hz is due to the fact that the gearbox forthnatural frequency is near the 5 times (1650Hz) the meshfrequency, and the mode shape is twisting of the upperhalf of the gearbox. The fundamental and the 2 times meshfrequency component are substantially smaller due to the lackof any gearbox natural frequencies near 333Hz and 666Hz.
Mathematical Problems in Engineering 7
Mode 5: frequency, 2375.3Hz Mode 6: frequency, 2729.2Hz Mode 7: frequency, 2783.3Hz Mode 8: frequency, 2885.3Hz
Mode 1: frequency, 675.8Hz Mode 2 : frequency, 1339.8Hz Mode 3: frequency, 1519.7Hz Mode 4: frequency, 1662Hz
Figure 8: The mode shapes of the gearbox.
1.051.201.351.501.65
0.000 0.005 0.010 0.015 0.020 0.025 0.030
Time (s)
T
Resp
onse(๐
m)
(a) Node-displacement response
0.080.16
Frequency (Hz)
Mesh frequency
0 500 1000 1500 2000 2500 3000
2ร 3ร4ร
5ร
6ร
Am
plitu
de
(N)
(b) Vibration frequency spectra
Figure 9: The gear box dynamic response.
4.4. Gearbox Frequency Spectrum for Noise. The frequencyresponses corresponding to the calculated vibration velocitiesof the surface of the gearbox are inputted into the BEMto analyze the distribution of sound-pressure levels aroundthe gearbox. In order to ensure that the vibration datatransmission is correct, both the BE-model and FE-model aremeshed in the same way, where the nodes of the two modelsare mutually corresponding.
Hemispherical sound field is defined outside of the gear-box and is shown in Figure 6. Three representative fieldpoints are selected in the sound field; they are located atthe top of the gearbox (field point a) and the left and rightsides of the gearbox (field points b and c). The frequency
0
25
50
75
Frequency (Hz)
Soun
d pr
essu
re le
vel (
dB)
0 500 1000 1500 25002000
โ25
2ร 4ร5ร
abc
Figure 10: The frequency spectrum for noise.
response of sound pressure level is shown in Figure 10.The noise of the field point at top gearbox is lower thanright and left side, due to the fact that most of the modeshapes are swing or torsional vibrations that make normalvibration of the gearbox side plate more violent than topsurface. The amplitudes and general shapes of the curves band c are similar; the frequency components of considerablemagnitudes are observed at the mesh frequency of 333Hzand doubling frequency with three very large components atthe 2 times mesh frequency, 4 times mesh frequency, and 5times mesh frequency; the largest peak value is 50 dB. Whenthe frequency of excitation is larger than 1665Hz, the soundpressure level is decreased as the frequency increases.
8 Mathematical Problems in Engineering
2000 4000 6000 8000
0
1
2
3
fmfb2 fb4
2ร 3ร 4ร 5ร 6ร
Am
plitu
de (๐
)
Rota
te sp
eed
(r/m
in)
Frequency (Hz)
3000
2500
2000
1500
1000
Figure 11: The waterfall of the gearbox dynamic response.
Resonant frequency band
Noi
se (d
B)
fmfb1 3ร 4ร 5ร 6ร
0
826446280
2000 4000 6000 8000
1000
50010000
1500
2000
2500
3000
โ82โ64โ46โ28โ10
Rota
tiona
l spe
ed(r/m
in)
Frequency (Hz)
Figure 12: The waterfall of the gearbox noise.
5. The Effect of Rotation Speed onthe Vibration and Noise
With change of the rotational speed, not only the gear pairmeshing state will change, but also the frequency of thevarious harmonics will change at the same time. In order toresearch the effect of the rotation speed, the dynamic bearingforce, gearbox vibration, and noise radiation are calculatedwhen the rotation speed is within the range of 500 r/min and3000 r/min.
5.1. The Effect of Rotation Speed on the Gearbox DynamicResponse. Increasing the input speed steadily from 500 r/minto 3000 r/min, a family of vibration and noise spectrum isobtained. Thus, two waterfall diagrams have been created, asshown in Figure 11 (๐๐ denotes mesh frequency; ๐๐2 and ๐๐4
denote the second and forth nature frequency of the gearbox).The spectral map illustrates how the various harmonics
fall along radial lines and can, thus, be separated from
View hole lid
Roof panel
Side plates of the upper half of the gearbox
Bearing cover
Front and rear panels
Right side
The front
Left side
The back
Side plates of the bottom half of the gearbox
Figure 13:The gear box panel definition.Viewhole lid (1); roof panel(2); side plates of the upper half of the gearbox (3, 4); bearing cover(5, 6, 7, and 8); side plates of the bottom half of the gearbox (9, 10, 11,12, 13, and 14); front and rear panels (15, 16).
the constant frequency components due to excessive ampli-fication by a structural resonance. The excitation consistsof harmonic components whose frequency is a multiple ofthe corresponding gearโs rotational speed, so the major com-ponents of response fall along radial lines. Meanwhile, thegearbox produces violent vibration near 1664Hz in differentrotational speed, since the 2 times the mesh frequency in2500 r/min, 3 times the mesh frequency in 1600 r/min, 4times the mesh frequency in 1250 r/min, and 5 times themesh frequency in 1000 r/min are equal to the fourth naturalfrequency; the samephenomenonoccurs near the second andthird natural frequency. So it means that the second, third,and fourth natural frequency are sensitive to the dynamicbearing force.
5.2. The Effect of Rotation Speed on the Gearbox NoiseRadiation. The gearbox noise spectral map in dB is shownin Figure 12. Note that the frequency components of thegearbox noise spectrum are not intense at low speed, asthe rotational speed increases, and noise radiation wasgradually strengthened. The distribution of sound pressureand dynamic response are consistent under various speeds;the resonant frequency band is produced at the range of670Hz, 1300โ1700Hz, and 3000โ4000Hz, which are near thegearbox natural frequency. So in order to reduce the gearboxvibration and noise radiation, the vibration at the resonantfrequency band should be reduced during the gearbox designstage.
6. Gearbox Improvement
6.1. Gearbox Panel Acoustic Contribution. The vibration andnoise of the gearbox are sensitive to the shape and structureof its housing. It is necessary to determine the noise contri-bution of each panel in the resonance region, which provideforceful basis as the gearbox structure is improved.
In order to quantify the noise proportion of each plate tothe whole structure, we introduce the concept of panel acous-tic contribution coefficient, which is the ratio of the noise
Mathematical Problems in Engineering 9
0
4
8
12
16
20Pa
nel c
ontr
ibut
ion
coeffi
cien
t
โ4
Panel number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1665Hz
(a) Panel contribution at 1665Hz
0
20
40
60
Pane
l con
trib
utio
n co
effici
ent
โ20
โ40
Panel number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
667Hz
(b) Panel contribution at 667Hz
Figure 14: The gear box panel contribution.
Ribs Additive thickness
Figure 15: Improved gearbox.
pressure produced by vibration of the panels to the overallnoise pressure:
๐ท๐ = ๐ ๐
๐๐๐โ
|๐|2, (15)
where ๐โ is the conjugate complex number of the sound
pressure for the point and ๐ is its real part.If the phase difference between the panel sound pressure
and the overall sound pressure is less than 90โ, the overallsound pressure will increase with the raise of the panelvibration velocity, and the contribution coefficient is definedas positive; otherwise, it is negative. The radiating noise canbe reduced effectively if vibration of the panelswhose acousticcontributions are positive and values are large can be reduced.
Each closed surface of the gearbox is defined as a panel,and the part whose radiation area is too small is neglected,such as the area of corner cutting. The whole gearbox outersurface is divided into 16 panels, as shown in Figure 13.
The panel acoustic contribution coefficient is shown inFigure 14, noted that the contributions of the roof panel andthe front and rear panels are greater than other panels whenthe excitation frequency is 1665Hz. When the excitationfrequency is 667Hz, the contributions of the roof and sideplates of the upper half of the gearbox are bigger. Furtheranalysis indicates that the noise ismainly caused by the panelsof the upper half of the gearbox. Reducing vibrant intensity of
Table 2: The gear box natural frequencies (Hz).
Mode steps Original model Plan 1 Plan 21st 716.5 791.2 770.72nd 1518.8 1684.4 1631.83rd 1682.3 1847.2 1800.14th 1843.7 2138.1 2001.45th 2459 2887 2765.36th 2881.6 3178.4 3010.87th 2887.3 3431.6 3259.48th 3043.9 3434.3 3276.9
the panels 2, 3, 4, 15, and 16 is important to noise control ofthe gear reducer.
6.2. Gearbox Improvement. In order to reduce the intensityof vibration of the upper half of the gearbox and make thegearbox natural frequency avoid the 2 times and 5 times themesh frequency, two low-noise design plans are proposed.The first plan increases the thickness of the side plates ofthe bottom half of the gearbox with 4mm. Another one, thegearbox stiffness was strengthened by using ribs on the sideplates, as Figure 15 shown.The natural frequency is shown inTable 2.
10 Mathematical Problems in Engineering
0
15
30
45
60
75
Frequency (Hz)
Soun
d pr
essu
re le
vel (
dB)
b a
c
โ30
โ15
12dB
0 500 1000 1500 2000 2500
Figure 16: The frequency spectrum for noise.
The frequency-noise spectra of the gearbox pre- andpostimprovement are shown in Figure 16, where curves a, b,and c represent the distribution of sound pressure level forthe original model and the improved models, respectively.As can be seen, the differences in mesh frequency doublingare considerable. The noise of improved gearbox is reducedobviously when the extinction frequency is below 1700Hz.The sound pressure level is reduced about 12 dB at 665Hz andabout 9 dB at 1332Hz in magnitude.
With comparative analysis of the two low-noise designplans, the effect of increasing gearbox thickness and ribs onreducing noise and vibration is almost the same, but plan 1will increase more weight and take upmore interior room, soit is more realizable to provide stiffening ribs on the gearbox.
7. Conclusions and Summary
A procedure for predicting the vibration and noise of gearreducer is developed, in which both gear transmission systemdynamic characteristics and gearbox dynamic characteristicsare considered. The dynamic bearing force is taken as theexcitation; the gearbox vibrations and noise radiating arecalculated by using FEM/BEM.The resonant frequency bandof the gearbox is obtained. Then the low-noise gearbox wasdesigned based on the result of modal analysis and acousticpanel contribution analysis. It is available to reduce the noiseradiation of the gearbox through increasing the structuralstiffness of the gearbox and reducing the vibration of thepanels whose acoustic contribution coefficients are positiveand values are large.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this article.
References
[1] M. S. Abbes, S. Bouaziz, F. Chaari, M. Maatar, and M. Haddar,โAn acoustic-structural interactionmodelling for the evaluation
of a gearbox-radiated noise,โ International Journal ofMechanicalSciences, vol. 50, no. 3, pp. 569โ577, 2008.
[2] P. Velex and M. Maatar, โA mathematical model for analyzingthe influence of shape deviations and mounting errors on geardynamic behaviour,โ Journal of Sound andVibration, vol. 191, no.5, pp. 629โ660, 1996.
[3] J.-L. Dion, S. Le Moyne, G. Chevallier, and H. Sebbah, โGearimpacts and idle gear noise: experimental study and non-lineardynamic model,โMechanical Systems and Signal Processing, vol.23, no. 8, pp. 2608โ2628, 2009.
[4] M. Barthod, B. Hayne, J.-L. Tebec, and J.-C. Pin, โExperimentalstudy of dynamic and noise produced by a gearing excited by amulti-harmonic excitation,โApplied Acoustics, vol. 68, no. 9, pp.982โ1002, 2007.
[5] M. Kato, K. Inoue, K. Shibata, and H. Zhou, โEvaluation ofsound power radiated by a gearbox,โ in Proceedings of theInternational Gearing Conference (Inter Gearing โ94), pp. 69โ74,Newcastle, UK, 1994.
[6] F. B. Oswald, D. P. Townsend, M. J. Valco, R. H. Spencer, R. J.Drago, and L. W. Joseph, โInfluence of gear design parameterson gearbox radiated noise,โ in Proceedings of the InternationalGearing Conference (Inter Gearing โ94), Newcastle, UK, Septem-ber 1994.
[7] F. K. Choy,W. Qian, J. J. Zakrajsek, and F. B. Oswald, โVibrationand noise analysis of a gear transmission system,โ in Proceedingsof the 29th Jiont Propulsion Conference and Exhibit, Monterey,Calif, USA, June 1993.
[8] Z. Yanyan and G. Zhen, โAnalysis and Control of GearboxNoise,โ China Mechanical Engineering, vol. 2, no. 5, pp. 55โ57,1994.
[9] A. Kahraman andG.W. Blankenship, โEffect of involute contactratio on spur gear dynamics,โ Journal of Mechanical Design, vol.121, no. 1, pp. 112โ118, 1999.
[10] S. C. Kostic and M. Ognjanovic, โThe noise structure of geartransmission units and the role of gearbox walls,โ FME Trans-actions, vol. 35, no. 2, pp. 105โ112, 2007.
[11] J. Tuma, โGearbox noise and vibration prediction and control,โInternational Journal of Acoustics and Vibrations, vol. 14, no. 2,pp. 99โ108, 2009.
[12] T.-J. Lin, R.-K. Jiang, R.-F. Li, and W. Liu, โNumerical sim-ulation of dynamic response and shock resistance of marinegearbox,โ Journal of Vibration and Shock, vol. 26, no. 12, pp. 14โ22, 2007.
[13] L. Runfang andW. Jianjun, System of the Gear VibrationTheory,Science Press, Beijing, China, 1997.
[14] Y. T. Gu and G. R. Liu, โA meshless local petrov-galerkin(MLPG) method for free and forced vibration analyses forsolids,โ Computational Mechanics, vol. 27, no. 3, pp. 188โ198,2001.
Submit your manuscripts athttp://www.hindawi.com
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical Problems in Engineering
Hindawi Publishing Corporationhttp://www.hindawi.com
Differential EquationsInternational Journal of
Volume 2014
Applied MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Probability and StatisticsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical PhysicsAdvances in
Complex AnalysisJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
OptimizationJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CombinatoricsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Operations ResearchAdvances in
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Function Spaces
Abstract and Applied AnalysisHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of Mathematics and Mathematical Sciences
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Algebra
Discrete Dynamics in Nature and Society
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Decision SciencesAdvances in
Discrete MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com
Volume 2014 Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Stochastic AnalysisInternational Journal of