Post on 03-Feb-2016
description
Fusion:Basic Principles and Current Progress
Lukáš Maretta
What is Nuclear Fusion?
• Nuclear Fusion is the energy-producing process taking place in the core of the Sun and stars
• The core temperature of the Sun is about 15 million °C. At these temperatures hydrogen nuclei fuse to give Helium and Energy. The energy sustains life on Earth via sunlight
Energy Released by Nuclear Reactions
• Light nuclei (hydrogen, helium) release energy when they fuse (Nuclear Fusion)
• The product nuclei weigh less than the parent nuclei
• Heavy nuclei (Uranium) release energy when they split (Nuclear Fission)
• The product nuclei weigh less than the original nucleus
Energy Released by NuclearFusion and Fission
• Fusion reactions release much higher energies than Fission reactions
Fusion Reactions• Deuterium – from water
(0.02% of all hydrogen is heavy hydrogen or deuterium)
• Tritium – from lithium(a light metal common in the Earth’s crust)
Deuterium + Lithium → Helium + Energy
This fusion cycle (which has the fastest reaction rate) is of interest for Energy Production
The World, particularly developing countries, needs a New Energy Source
• Growth in world population and growth in energy demand from increased industrialisation/affluence will lead to an Energy Gap which will be increasingly difficult to fill with fossil fuels
• Without improvements in efficiency we will need 80% more energy by 2020• Even with efficiency improvements at the limit of technology we would still
need 40% more energy
Incentives for Developing Fusion• Fusion powers the Sun and the stars
– It is now within reach for use on Earth
• In the fusion process lighter elements are “fused” together, making heavier elements and producing prodigious amounts of energy
• Fusion offers very attractive features:– Sustainable energy source
(for DT cycle; provided that Breeding Blankets are successfully developed)
– No emission of Greenhouse or other polluting gases
– No risk of a severe accident
– No long-lived radioactive waste
• Fusion energy can be used to produce electricity and hydrogen, and for desalination
Fission (PWR)
Fusion structure
Coal
Tritium in fusion
Fusion Energy – Disadvantages
• Fusion reaction is difficult to start!– High temperatures (Millions of degrees) in a
pure High Vacuum environment are required– Technically complex and high capital cost
reactors are necessary
• More Research and Development is needed to bring concept to fruition– The physics is well advanced but requires
sustained development on a long time scale (20 to 40 years)
Fusion The President recognizes Fusion’s potential
Fusion Power Station Schematic
Plasmas• A Plasma is an ionised gas. A mixture of positive ions
and negative electrons with overall charge neutrality• Plasmas constitute the 4th state of matter, obtained at
temperatures in excess of 100,000 degrees• Plasmas conduct electricity and heat
Self-Sustaining or ‘Ignited’ Plasmas• Deuterium – tritium fusion reaction:
D + T → 4He + n + Energy
The 4He nuclei (‘’ particles) carry about 20% of the energy and stay in the plasma. The other 80% is carried away by the neutrons and can be used to generate steam.
Plasmas become Self-sustaining or Ignited when there is enough power to balance losses from the plasma
• In stars plasma particles (including a’s) are confined mainly by gravity and high plasma densities achieved
• On Earth: – hot dense plasmas can be confined in Magnetic fields (Magnetic
Confinement Fusion)– superdense plasmas can be obtained by imploding solid deuterium-
tritium pellets (Inertial Confinement Fusion)
• Laser implosion of small (3mm diameter) solid deuterium–tritium pellets produces fusion conditions
• Pressure generation
• CompressionFuel is compressed by rocket-like blow off200,000 million atmospheres in core
• Ignition and burn
– Peak compression fuel reaches 1000-10000 times liquid density for extremely short time (10–11 seconds)
– Core is heated and ‘spark ignition’ occurs
Inertial Confinement
• Magnetic fields cause charged particles to spiral around field lines. Plasma particles are lost to the vessel walls only by relatively slow diffusion across the field lines
• Toroidal (ring shaped) system avoids plasma hitting the end of the container
• The most successful Magnetic Confinement device is the TOKAMAK (Russian for ‘Toroidal Magnetic Chamber’)
Magnetic Confinement
The Tokamak:A Transformer Device
How Large a Device?• For fusion power to ignite a plasma:
– There has to be sufficient density of deuterium and tritium ions (ni);
– The reacting ions have to be hot enough (Ti);– The energy from the fusion ’s must be confined for long
enough (E).
E increases with the square of the device size – a large machine is needed.
• The fusion triple product (niTiE) and the ion temperature (Ti) must both be large enough (below a certain temperature the fusion reaction probability is too small)
pressure (niTi) ≥ 2 atmospheresconfinement time > 5 seconds
plasma ion temperature ≈ 100-200 Million °C
JET(Joint European Torus)
• The Joint European Torus (“JET”) is the largest magnetic fusion test device in the world.
• Situated at Culham, Oxfordshire, JET:– was constructed between 1978-1983;– has operated 1983 - present;– is the largest Project in the European Union’s
Fusion programme• The participating countries are the 15 EU
nations + Switzerland• The Project has a capital investment of over
£500 Million and an Annual Budget of around £53 Million
JET
• JET is a Tokamak with:– Torus radius 3.1m– Vacuum vessel 3.96m
high x 2.4m wide– Plasma volume 80m3
– Plasma current up to 5MA
– Main confining field up to 4 Tesla (recently upgraded from 3.4 Tesla)
Progress with MagneticConfinement Fusion
• JET and the similar large Tokamaks in:– USA Tokamak Fusion Test Reactor (TFTR)
Doublet IIID Tokamak (DIIID)– Japan Japanese Tokamak – 60U (JT-60U)
Have made significant progress in:– Technology of fusion;– Approaching the conditions of an Ignited plasma;– Predicting the behaviour of a reactor plasma;– Controlling impurities which enter the plasma– Operating with Tritium fuel
Progress towards Ignition
• The Fusion Triple Product (PiE = niTiE) required to reach ignition can be compared with leading edge performance of the devices year-on-year.
• The best plasmas now need an improvement of only 6 in performance. This requires a new larger device.
Controlling Impurities• Fuel Impurities are a major threat to reactor success
• Two primary sources of impurities exist:– Helium “ash” from the fusion reaction– Material impurities from plasma-wall interactions
• Impurities must be controlled since they:– Radiate energy, and reduce the plasma temperature– Dilute the fuel, thereby preventing ignition
• The “Magnetic Divertor” is a device for controlling impurities. This has been tested successfully in JET.
Three different concepts have been compared.Results agree with code predictions.
Progress with MagneticConfinement Fusion
• Impurities (C, Be) are produced by ion impact on target and are ionised in the plasma and returned to target
Pumped Divertor in JET
Fusion Power Development
The diagram encompasses :• Two pulses with 10% T in D in JET in 1991;• A result from the D-T studies on TFTR (1993 to 1997);• High fusion power and quasi-steady-state fusion power from the
>200 pulses with >40% T in D in the JET D-T experiments of 1997.
ITER Design - Main Features
Divertor
Central Solenoid
Outer Intercoil Structure
Toroidal Field Coil
Poloidal Field Coil
Machine Gravity Supports
Blanket Module
Vacuum Vessel
Cryostat
Port Plug (IC Heating)
Torus Cryopump
ITER Objectives
Programmatic• Demonstrate the scientific and technological feasibility of fusion
energy for peaceful purposes.
Technical• Demonstrate extended burn of DT plasmas, with steady state as the
ultimate goal.• Integrate and test all essential fusion power reactor technologies and
components. • Demonstrate safety and environmental acceptability of fusion.
ITER Parameters
Total fusion power 500 MW (700MW)
Q = fusion power/auxiliary heating power ≥10 (inductive)
Average neutron wall loading 0.57 MW/m2 (0.8 MW/m2)
Plasma inductive burn time ≥ 300 s
Plasma major radius 6.2 m
Plasma minor radius 2.0 m
Plasma current (inductive, Ip) 15 MA (17.4 MA)
Vertical elongation @95% flux surface/separatrix 1.70/1.85
Triangularity @95% flux surface/separatrix 0.33/0.49
Safety factor @95% flux surface 3.0
Toroidal field @ 6.2 m radius 5.3 T
Plasma volume 837 m3
Plasma surface 678 m2
Installed auxiliary heating/current drive power 73 MW (100 MW)
ITER Site Layout
ITER Location
Caradache (France) Rokkasho (Japan)
Fusion Nuclear Technology (FNT)
FNT Components from the edge of the Plasma to TF Coils (Reactor “Core”)
1. Blanket Components
2. Plasma Interactive and High Heat Flux Components
3. Vacuum Vessel & Shield Components
4. Tritium Processing Systems
5. Instrumentation and Control Systems
6. Remote Maintenance Components
7. Heat Transport and Power Conversion Systems
a. divertor, limiter
b. rf antennas, launchers, wave guides, etc.
Other Components affected by the Nuclear Environment
Fusion Power & Fuel Cycle Technology
Plasma
Radiation
Neutrons
Coolant for energy conversion
First Wall
Shield
Blanket Vacuum vessel
Magnets
Tritium breeding zone
Blanket (including first wall)Blanket Functions:
A. Power Extraction– Convert kinetic energy of neutrons and secondary gamma-rays into heat
– Absorb plasma radiation on the first wall
– Extract the heat (at high temperature, for energy conversion)
B. Tritium Breeding– Tritium breeding, extraction, and control
– Must have lithium in some form for tritium breeding
C. Physical Boundary for the Plasma– Physical boundary surrounding the plasma, inside the vacuum vessel
– Provide access for plasma heating, fueling
– Must be compatible with plasma operation
– Innovative blanket concepts can improve plasma stability and confinement
D. Radiation Shielding of the Vacuum Vessel
Blanket Materials1. Tritium Breeding Material (Lithium in some form)
Liquid: Li, LiPb (83Pb 17Li), lithium-containing molten salts
Solid: Li2O, Li4SiO4, Li2TiO3, Li2ZrO3
2. Neutron Multiplier (for most blanket concepts)
Beryllium (Be, Be12Ti)
Lead (in LiPb)
3. Coolant
– Li, LiPb – Molten Salt – Helium – Water
4. Structural Material– Ferritic Steel (accepted worldwide as the reference for DEMO)
– Long-term: Vanadium alloy (compatible only with Li), and SiC/SiC
5. MHD insulators (for concepts with self-cooled liquid metals)
6. Thermal insulators (only in some concepts with dual coolants)
7. Tritium Permeation Barriers (in some concepts)
8. Neutron Attenuators and Reflectors
A Helium-Cooled Li-Ceramic Breeder Concept: Example
Material Functions•Beryllium (pebble bed) for neutron multiplication
•Ceramic breeder (Li4SiO4, Li2TiO3, Li2O, etc.) for tritium breeding
•Helium purge (low pressure) to remove tritium through the “interconnected porosity” in ceramic breeder
•High pressure Helium cooling in structure (ferritic steel)Several configurations exist (e.g. wall parallel or “head on” breeder/Be arrangements)
Li/Vanadium Blanket Concept
Breeding Zone
(Li flow)
Primary Shield
Secondary Shield
Reflector
Li
Li
Li
Secondary shield(B4C)
Primary shield
(Tenelon)
Reflector
Lithium
Lithium
Vanadium structure
Vanadium structure
Flows of electrically conducting coolants will experience complicated magnetohydrodynamic (MHD) effects
What is magnetohydrodynamics (MHD)?– Motion of a conductor in a magnetic field produces an EMF that can
induce current in the liquid. This must be added to Ohm’s law:
– Any induced current in the liquid results in an additional body force in the liquid that usually opposes the motion. This body force must be included in the Navier-Stokes equation of motion:
– For liquid metal coolant, this body force can have dramatic impact on the flow: e.g. enormous MHD drag, highly distorted velocity profiles, non-uniform flow distribution, modified or suppressed turbulent fluctuations
)( BVEj
BjgVVVV
11
)( 2pt
-1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Large MHD drag results in large MHD pressure drop
• Net JxB body force p = cVB2 where c = (tw w)/(a )
• For high magnetic field and high speed (self-cooled LM concepts in inboard region) the pressure drop is large
• The resulting stresses on the wall exceed the allowable stress for candidate structural materials
• Perfect insulators make the net MHD body force zero
• But insulator coating crack tolerance is very low (~10-7).
– It appears impossible to develop practical insulators under fusion environment conditions with large temperature, stress, and radiation gradients
• Self-healing coatings have been proposed but none has yet been found (research is on-going)
Lines of current enter the low resistance wall – leads to very high induced current and high pressure drop
All current must close in the liquid near the wall – net drag
from jxB force is zero
Conducting walls Insulated wall
-1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Dual Coolant Concept Designs from EU and USA
Cross section of the breeder region unit cell(ARIES)
Summary
• The D-T Fusion process offers the promise of:– Virtually unlimited energy source from cheap abundant fuels;– No atmospheric pollution of greenhouse and acid rain gases;– Low radioactive burden from waste for future generations.
• Tremendous Progress has been achieved over the past decades in plasma physics and fusion technology.
• Fusion R&D involves many challenging areas of physics and technologies and is carried out through extensive international collaboration
• EU,J, USA, RF, PRC, Korea are about to construct ITER to demonstrate the scientific and technological feasibility of fusion energy (ITER will produce 500MW of fusion power and the project total cost is about $15B)