FRP - studiestoday.com Class 11 Engineering Graphics...ANGLE PROJECTION METHOD OR THIRD ANGLE...

Chapter 6ORTHOGRAPHIC PROJECTIONS OF SIMPLE MACHINE BLOCKS

6.1 INTRODUCTION

We have already made you aware of many simple geometrical shapes (laminae), projected on such planes (vertical plane, horizontalplane and other auxiliary planes) while projecting the various views of simple regular geometrical solids. Similarly, it is necessary tounderstand any machine block ascombination of the geometrical solids byadding solids together or removinggeometrical solids out of a single solid. Forexample, a hexagonal nut is formed out of ahexagonal prism by removing a smallcylinder and cutting internal helical groove(internal threads). Reverse of it is square boltin which square prism and small cylinder isone integral solid with external helicalgroove (external threads) cut on it.

In figure 6.1 a cube of 15 mm is removed outfrom a single solid i.e. a rectangular prism.

An orthographic projection is one positiondrawing. It takes several drawings to showand understand all the machine block form.The views are placed relative to each otheraccording to either of two schemes. FIRSTANGLE PROJECTION METHOD OR THIRDANGLE PROJECTION METHOD.

Note : However we are following only firstangle method of projection in all theexercises (According to CBSE prescribedsyllabus) Fig. 6.1

Downloaded from www.studiestoday.com

www.stud

iestod

Orthographic projections of simple machine blocks

6.2 UNDERSTANDING : SIMPLE MACHINE BLOCKS

FIG. 6.2 DO IT YOURSELF(i) No. of Vertical Faces..............(ii) No. of Horizontal Faces...........(iii) Give the dimension of Face ‘H1’ ...................(iv) Give the dimension of Face ‘V1’ ......................(v) No. of side Faces .....................

V = Vertical Face, H = Horizontal Face, I = Inclined Face, F = Front, S = Side and T = Top

www.stud

iestod

Engineering Graphics

FIG. 6.3 DO IT YOURSELF(i) No. of Vertical faces..............(ii) No. of Horizontal faces...........(iii) Give the dimension of face ‘V1’ ...................(iv) Give the dimension of face ‘H1’ ......................(v) No. of side faces .....................

www.stud

iestod

FIG. 6.4 DO IT YOURSELF

(i) No. of Vertical faces..............

(ii) No. of Horizontal faces...........

(iii) No. of Inclined faces.............

(iv) Give the dimension of face I in Top View ......................

Note : This inclined face is seen in Top View and in Front View

www.stud

iestod

FIG. 6.5 DO IT YOURSELF

(i) No. of Vertical faces..............

(ii) No. of Horizontal faces...........

(iii) No. of Inclined faces.............

(iv) Give the dimension of face I in Side View ..................

Note : This inclined face is seen in Top View and in Front View

www.stud

iestod

IMPORTANT OBSERVATIONS :

If the surface/face of an object is either parallel to the vertical plane or horizontal plane (Principal Planes) they appear to be inTRUE SHAPE in one of the three views and appear as a “line only” in other two views (as these faces are perpendicular to theplane of projection).

When a surface/face is inclined or making an angle with two planes at the same time, that surface/face is not seen in its TRUESHAPE in the plane to which it is inclined. It is seen in the plane to which it is inclined as a plane of reduced size due toforeshortening.

6.3 LET US FIND

Fill in the blanks by the corresponding line (as indicated)/Trueshape by observing the following views.

Pictorial View Orthographic View

Surfaces Indicated As

Front View Top View Side View

(I) H ______1_____ True Shape ______2_____

(ii) H1 ____________ ____________ ____________

(iii) V ____________ ____________ ____________

(iv) S ____________ ____________ ____________

(v) S1 ____________ ____________ ____________

Fig. 6.6

www.stud

iestod

6.4 MACHINE BLOCKS WITH (HORIZONTAL AND VERTICAL FACES)

Fig. 6.7

www.stud

iestod

Fig. 6.8

www.stud

iestod

Fig. 6.9

www.stud

iestod

Fig. 6.10

www.stud

iestod

Fig. 6.11

www.stud

iestod

Fig. 6.12

www.stud

iestod

Fig. 6.13

www.stud

iestod

Fig. 6.14

www.stud

iestod

Fig. 6.15

6.5 MACHINE BLOCKS WITH (HORIZONTAL, VERTICAL AND INCLINED FACES)

www.stud

iestod

Fig. 6.16

www.stud

iestod

Fig. 6.17

www.stud

iestod

Fig. 6.18

www.stud

iestod

Fig. 6.19

6.6 MACHINE BLOCKS : (HORIZONTAL, VERTICAL AND CURVED FACES)

www.stud

iestod

Fig. 6.20

www.stud

iestod

Fig. 6.21

www.stud

iestod

Fig. 6.22

www.stud

iestod

Fig. 6.23

6.7 MACHINE BLOCKS : (HORIZONTAL, VERTICAL, CURVED AND INCLINED FACES)

www.stud

iestod

Fig. 6.24

www.stud

iestod

6.8 MISCELLANEOUS EXERCISES

Fig. 6.25

www.stud

iestod

Fig. 6.26

www.stud

iestod

Fig. 6.27

www.stud

iestod

Fig. 6.28

www.stud

iestod

Fig. 6.29

www.stud

iestod

Fig. 6.30

www.stud

iestod

Fig. 6.31

www.stud

iestod

Fig. 6.32

www.stud

iestod

Fig. 6.33

www.stud

iestod

Fig. 6.34

www.stud

iestod

Fig. 6.35

www.stud

iestod

Fig. 6.36

www.stud

iestod

FRP - studiestoday.com Class 11 Engineering Graphics...ANGLE PROJECTION METHOD OR THIRD ANGLE...

Documents

Transcript of FRP - studiestoday.com Class 11 Engineering Graphics...ANGLE PROJECTION METHOD OR THIRD ANGLE...

Figure 3-10 Horizontal projection. Figure 3-11 Projection at an angle.

Projection and inverse projection as a method of reformulating linear and integer programmes

Back projection method ,boulanouar

r a c t s E x t 2 p a g e o f 8 - WordPress.com...for the units and the projection rule. American (3rd angle projection) European (1st angle projection) Depending from the template

PROJECTION METHOD

4 Market Projection Method

Unit 16: Engineering Drawing for Technicians Third angle projection

2D Drawings - Mr. McLaren's Webspace · 2018. 9. 6. · Third-angle Projection First-angle Projection First and Third Angle Projections • First Angle • Third Angle . Orthographic

PROJECTION METHOD - Weebly

UNIT III PROJECTION OF POINTS, LINES AND PLANE …chettinadtech.ac.in/storage/11-09-13/11-09-13-05-23-23-1147... · First angle projection b. Third angle projection ... views are

3RD ANGLE PROJECTION PROJECTION' should be displayed prominently on each drawing sheet. Third angle projection IS-@JI Either the symbol or the drawing callout '1ST ANGLE 1 ST ANGLE

The Benchmark Separation Projection Method for Predicting ...

allmadeeasy.files.wordpress.com€¦ · Web view09.09.2013 · Draw the following orthographic views using. the FIRST angle projection method. Use the Aligned System of dimensioning.

Reﬂection-Projection Method for Convex Feasibility ...

PROJECTION METHOD III: SPATIAL DISCRETIZATION ON THE ...

Multiview Sketching Projection - Willkommen an der ... - ˛ ˜ For Third Angle Projection (the method in the U.S.) Imagine that the walls of the box are hinged and unfold the views

A Projection Method to GenerateA Projection Method to ...edubois/anaglyph/anaglyph_010508.pdfA Projection Method to GenerateA Projection Method to Generate Anaglyph Stereoscopic Images

THIRD ANGLE PROJECTION - CommScope · 1 of 4 auth. group third angle projection third angle projection drawn by third angle projection unless otherwise specified dimensions are in

1 PTT 105/3 Engineering Graphicss. Projection Theory Multi-view Projection Principle views & View placement Projection angle Detail drawing:

1 Views using first angle projection; used in Europe. Views using third angle projection; used in North America DRAWINGS.