Post on 06-May-2018
Snap -Tys™
1
SNAP-TY
SNAP-TY WRENCH
Any typeSnap-Ty
EndEnd Wall
Form Wall Form
½"½"
AR Snap-Tys are fabricated to fit either prefabricated panels orbuilt-in-place forms. They are specifically designed for quick, easy andaccurate erection of light formwork. End sizes can be as short as 1¼" for Steel Washer Snap-Tys or as long as you need them to fit a special condition. Snap-Tys can be fabricated for any required wall thickness up to19'-6" length. Spreader washers are precisely located to give exact wallthicknesses. Break points are located at specified distances back from thewall face to permit clean stripping without spalling. All standard Tys aremanufactured to provide set back from the wall face. The small Ty holesand washer indentations are easily pointed, grouted or plugged. Consult the Technical Department for minimum wall thicknesses. For exposedconcrete or where a longer set back is required, the NCA Space-Ty™ issuggested.
Snap-Tys are stocked in 4¾" or 8½" ends for standard wall thicknesses.
2,250 lbs Snap-Tys areavailable in stainless steel uponrequest.
PLASTIC SNAP-TY PLUG
PLYHOLE PATCH
2
SNAP-TY
FORM BRACE ALIGNERPRESSED STEEL TY WEDGETYPE H TY-WEDGE
Plastic Cone Snap-Ty (PC)
37500
The AR Plastic Cone Snap-Ty and the AR Heavy Duty Plastic Cone Snap-Ty are equipped with a Plastic Cone Spreader providing for a 1" set back manufactured for specified wall thicknesses. The plastic cone reduces the likelihood of concrete paste thicknesses. The plastic cone reduces the likelihood of concrete paste seepage and protects the break back. The break back is approximately smaller than the cone length. The estimated break back is approximately ". The table provides the length and taper of the cones. Special size cones areavailable as custom orders. Available in stainless steel.
1/8" 7/8
STANDARD 2.25MSAFE WORKING LOAD
2,250 LBS2:1 Safety Factor
Set back
1"
Taper Inside to outside
3/8" to 1"
Plastic ConeSnap-Ty
Form½"
Wall Form
Overall length (inside to inside of head)
End
½"
End For architechtural design, insert thePlastic Snap-Ty Plug once form work hasbeen removed.
Plastic ConeSnap-Ty
PlasticSnap-TyPlug
The AR Plastic Washer Snap-Ty and Heavy Duty Plastic Washer Snap-Ty are equipped with a plastic washer,provide for a 1/8" to 3/16" break back less than the Plastic Washer Thickness and are manufactured for specified
HEAVY DUTY 3M SAFE WORKING LOAD
3,000 LBS2:1 Safety Factor
HEAVY DUTY 3M SAFE WORKING LOAD
3,000 LBS2:1 Safety Factor
STANDARD 2.25MSAFE WORKING LOAD
2,250 LBS2:1 Safety Factor
Plastic Washer Snap-Ty (PW)
Plastic WasherSnap-Ty
EndEnd Wall
Form Wall Form
½" ½"
Plastic Washer break back is1/8" to 3/16" less than theplastic washer thickness.
wall thicknesses. The Hex Head allows the Ty end to be broken back prior to removal of the forms, allowing for ease of stripping. Available in stainless steel.
3
TYSCRU
LAGNUTWATERSEAL 2-STRUT WATERSEAL 4-STRUT BATTER WASHERFLAT WASHER
Flat Washer thickness Flat Washerthickness
Tyscru length
Coil penetration
Wall thicknessForm Form thickness
Setback Wedge
Lagstud Bolt length
The AR Tyscru is an extra strong, resistance welded Ty designed to take the abuse encountere in medium andheavy concrete construction. An extremely simple Ty, capable of many combinations and uses in the field, it maybe used with or without Tycones or combined with Continuous Threaded Lagstud to form an Adjustable Tyscru.
Cone Tight Tyscru
1/2” 3/4”
60
50
40
4.56.75
9 9 9 9 97 69 9
18 18 18 18
30
20
T2 T2 T4T2 T2 T4
LAG
STU
D
7M
LAG
STU
D
9M
X 1
000
LBS
LAG
STU
D
1
8M
LAG
NU
T
BH
N
LAG
SNU
T
BH
N
COIL
NU
T
B
HN
-S
COIL
NU
T
B
HN
-L
COIL
NU
T
B
HN
-S
COIL
NU
T
B
HN
-L
10
0
T2 T4
COIL NUT
LAGNUT
LAGSTUD
Tyscru Systems
SAFE WORKING LOAD2:1 Safety Factor
4HANDLELAGNUT
TILT WASHERWINGNUT HEX ROD COUPLER
2-strut 4-strut
Standard Tyscru
AR Tyscrus are available in ½", ¾" and 1" diameters as 2 strut and 4 strut, fabricated to the required length to the nearest . For 1¼" and 1½" diameters, 4 and 6 Tyscrus are available.
Cone Tight Tyscru with screw on Ty Cone or Standard ends as illustrated are available in all sizes.
1” 1-1/4”
37.5
27
37
45
60
37
2730
18
27
37
25
37.5
18
37.5 37.5
13.5
T2 T4 T4 T4 T4 T6T4
LAG
STU
D
2
5 M
LAG
STU
D
37.5
M
LAG
STU
D
3
7 M
LAG
STU
D
60
M
LAG
STU
D
B
HN
LAG
STU
D
B
HN
COIL
NU
T
B
HN
-S
COIL
NU
T
B
HN
-L
COIL
NU
T
B
HN
-S1/8"
TYSCRU
5
TAPER-TY SYSTEM
Taper-Ty System
WasherTaper-TyWing
Nut
Washer
Use Handle Lagnut or Wing Nut
Taper-Ty
The AR Taper-Ty System is used where specifications permit the complete removal of the form-tie from the concrete wall. Taper-Tys are available with lag thread and a variety of hardware.
60
50
40
30
20
10
0
57000
35000
19000
3/4” TO 1/2” 3/4” TO 3/4” 1” TO 3/4” 1-1/4”” TO 1” 1-1/2” TO 1-1/2”
19000
9000
X 1
000
LBS
Taper Ty and Taper Bolt
SAFE WORKING LOAD2:1 Safety Factor
FLAT WASHERHANDLELAGNUT WINGNUT
LAG THREADCOUPLER PLASTIC FORM SPREADERBATTER WASHER
TILT WASHERHEX ROD COUPLERSHE - BOLTHEXNUT
She-Bolt
are high strength, adaptable units suitable for medium and heavy concrete AR She-Bolt Assembliesconstruction. Manufactured with external lag threads, they provide a positive system for use with gang formsand/or steel forms. The Inside Rods are manufactured with either national coarse thread or lag thread. If desired, continuousthreaded lagstud can be furnished in 5' or 10' lengths for field cutting to required specifications.
60
50
40
30
20
10
0
37500
1” X 1/2” 1-1/4” X 3/4” 1-1/2” X 1”
She Bolt
18000
9000
X 1
000
LBS
SAFE WORKING LOAD2:1 Safety Factor
6
SHE - BOLT
7
INTERIOR90/90
1/2”
HFR
1/2”
HFR
1/2”
HTB
H3/
4” H
HTBH
3/4”
HDH
TBH
3/4”
HDD
HTBH
1/2”
HFR
-HK
1/2”
HTB
H-HK
1/2”
HFR
-H
1/2”
HFR
-HW
1/
2” H
TBH-
H 1/
2” H
TBH-
HW
1/2”
HFR
-HA
1/2”
HFR
-HW
A 1/
2” H
TBH-
HA1/
2” H
TBH-
HWA
1/2”
HFR
-HAJ
1 CL
IP1/
2” H
RR-H
AF 2
CLIP
1/2”
HFR
-HAJ
-A 1
CLIP
1/2”
HRR
-HAJ
-A 2
CLIP
1/2”
PHFR
-H1/
2” PH
HFR-
H
1/2”
PHFR
-HA
1/2”
PHHF
R-HA
3/4”
HHT
BH-H
K 3/
4” H
DHTB
H-HK
3/
4” H
DDHT
BH-H
K
1/2”
HFR
-HKA
1/
2” H
TBH-
HKA
3/4”
HHT
BH-H
KA
3/4”
HDH
TBH-
HKA
3/4”
HDD
HTBH
-HKA
1/2”
HFR
#21/
2” H
FR #3
X 1
000
lbs.
X 1
000
lbs.
1/2”
HRH
-A #2
1/2”
HRH
-A #3
1/2”
HTB
H-A
3/4”
HHT
BH-A
3/
4” H
DHTB
H-A
HOOK 90 HALF 90ADJUSTABLE
90 PRECAST
90/45 HOOK 90 HALF 90
*Available as a special order
ADJUSTABLE 90 PRECAST
EXTERIOR
0
8
10
12
14
16
0
2
4
6
8
10
12
14
16
R S T
T
SAFE WORKING LOAD 2:1 Safety Factor
SAFE WORKING LOAD 2:1 Safety Factor
3.83 3
3.86 6
6
10
3.8 3.8
6 6
1.1
34.5
6
3.8
6
10
12
6
10
12
3.8
6
10
12
3.8 3.8
6 6
1.1
34.5
6
CUST
OM E
NGIN
EERE
D*
CUST
OM E
NGIN
EERE
D*
CUST
OM E
NGIN
EERE
D*
CUST
OM E
NGIN
EERE
D*
BRIDGE
LAGSTUD FLAT WASHER LAGSTUD BOLTHEX NUT
8
ANCHORING SYSTEMS
Preset Anchoring System AR Preset Anchoring System provides a simple, accurate and economical method for anchoring light poles, railings, guard rails and sign posts to structural concrete.The basic units can be manufactured to conform with any required configuration in size that will accommodate bolts or studs (either hi-strength galvanized or stainless steel) from 1/2" to 1-1/2" in diameter.
Type SGR 2 hole railing posts
TM TM Type DGR 1 for standard application
TM Type DGR -2S(with squared end studs)
Rock Bolt Anchoring System
SCT-L SST B-7HDR SDR SCT-N
SIZES 1/2” TO 2” SIZES 1”, 3/4”, 1” & 1-1/4” SIZES 1”, 3/4”, 1” & 1-1/4” SIZES 1”, 3/4”, 1”, 1-1/4” 1-3/8”,1-1/2” 1-3/4” & 2”
SIZES 1”, 3/4”, 1”, 1-1/4” 1-3/8”,1-1/2” 1-3/4” & 2”
SIZES 1”, 1-3/8” & 2”
Crane Bolt Anchoring System
STANDARD GRADE (Yellow - For Summer)
Other sizes available on request
DIAMETER LENGTH L1 L2
1 1/2" 48" 8" 14"
1 1/2" 40" 8" 8"
1 3/4" 48" 8" 14"
1 3/4" 40" 8" 8"
LENGTH
L2 L1
- Minimum yield strength of 44,000 psi
COLD WEATHER GRADE (Black - For Winter) - Charpy value of 15 ft.lb. @ -20°F- Minimum yield strength of 60,000 psi
DOUBLE KEY BEARING PLATE ROUND WASHER BEVELED WASHER HEX NUT CRANE BOLTS
9
PRECAST ACCESSORIES
Reinforcing Bar SupportsAR Reinforcing Bar Supports are used to support and space reinforcing steel. AR Bar Supports are manufactured according to specifications published by the Concrete Reinforcing Steel Institute. To eliminate rust spots or similar blemishes on the concrete surface specify AR’s Plastic Bar Supports.
SB
(SB) Slab BolsterUsed for supporting lower slab steel from slab form. Corrugations spaced 1” (25 mm) on centres serve as guides for spacing bars. Legs are spaced 5” (127 mm) on centre. Stocked in 3/4”, 1”, 1 1/2”, 2” (20, 25, 38 and 50 mm) in heights in 5’ (1525 mm) lengths.
(PSB) Slab Bolster And All Plastic Continous High ChairAR Plastic Slab Bolster is used for supporting lower slab steel from slab form. Corrugations spaced 1” (25 mm) on centres serve as guides for spacing bars. Legs are solid plastic 4” (100 mm) on centre. Supporting cross bar is made from high strength plastic coated steel.Corrosion-proof and lightweight for handling.
PSB
CHC
(CHC) Continuous High ChairAR Continuous High Chairs provide support for upper slab steel from slab form, eliminating carrier bars required with individual supports. Fabricated with plain steel legs (CHC) or with plastic tipped legs (PCHC). Supplied to order in heights from 2” to 12” (50 mm to 300 mm) in 1/4” (5 mm) increments and in 5’ (1525 mm) lengths with legs spaced at 6” (150 mm) o.c.
1 2 2
(25)
(50)
(63)
(20)in (mm)
1 2
5
5
6
7
1 2 6
(125)
(138)
(150)
(175)
(163)
(32)
1
2
3 4
3 4 1
HEIGHT
in (mm)
10
PRECAST ACCESSORIES
LINDEN CHAIR DATA SHEETSize Available 1-10 inches (25-254mm)
every 1/4” (6mm)
Colour concrete grey
Material
Strength a minimum 400 lbs. (180kg) / chair
reinforced, high impact polypropylene
Chemical Resistancy excellent
Packaging in heavy-duty uv protected poly bags Quantity varies by size
Installation good for both Black and Corrosion resistant rebar place chairs on deck forms can straddle bottom steel barsspacing depends on loads standard spacing is every 3-4 feet (0.9 - 1.2m)
Linden Chairs
mm
LINDEN CHAIRS SIZES AND PACKAGING WEIGHTSPCS/BAGinch LBS/MFT
1 25 500 30
32 500 3540 250 46
45 250 50
2 50 250 62
58 200 78
63 200 82
70 300 84
3 75 300 85
77 300 88
85 300 90
92 200 93
4 100 200 95
108 200 98
110 200 112
120
125
200 119
200 120
CTN SKID40
4040
40
40
40
40
25
25
25
25
25
25
25
25
25
25
SKID QTY20,000
20,00010,000
10,000
10,000
10,000
8,000
7,500
7,500
7,500
7,500
5,000
5,000
5,000
5,000
5,000
5,0005
133 200 125
140 200 130146 200 148
6 150 100 155
158 100 160
165 100 177
170 100 184
7 175 100 195
183 75 255
190 75 310
195 75 338
8 200 75 343
210 75 350
215 50 365
220 50 378
9 228
235
50 400
50 415
25
2525
25
25
25
25
25
25
25
25
25
25
25
25
25
25
5,000
5,0005,000
2,500
2,500
2,500
2,500
2,500
1,875
1,875
1,875
1,875
1,875
1,250
1,250
1,250
1,250
240 50 424
247 50 430
10 254 50 440
25
25
25
1,250
1,250
1,250
1 1 4
1 1 2
1 3 4
2 1 4
2 1 2
2 3 4
3 1 4
3 1 2
3 3 4
4 1 4
4 1 2
4 3 4
5 1 4
5 1 2
5 3 4
6 1 4
6 1 2
6 3 4
7 1 4
7 1 2
7 3 4
8 1 4
8 1 2
8 3 4
9 1 4
9 1 2
9 3 4
Corrosifree All Plastic Linden Chairs are used in slabs for supporting all types of reinforcing steel. Excellent for supporting epoxy coated rebar in bridge deck construction, or where-ever a corrosion free support is required. The high sizes have an arch design for straddling lower mats of rebar. The chair is made of High Impact polypropylene and its design gives it the strength of steel. Linden chairs are strong yet light in weight and packaged in poly bags for convenience of carrying around job sites.
Go to our web site at www.nca.ca for catalogue updates.
PRINTED IN CANADA CP0414/300
1-888-777-9272
Other Available Catalogues
• Concrete Forming Systems
• Precast Concrete Products
• Bridge Deck Forming & Hanging Systems
• Concrete Anchoring Systems
• Rock Anchoring and Bolt Systems
Acrow-Richmond provides over 45 years of experience in on site solutions and is one of North America’s leading manufacturers and distributors of concrete form hardware, accessories and construction products.
Acrow-Richmond is committed to deliving exceptional value to our customers, our employees, our suppliers and our shareholders through operational excellence, providing innovative and quality products, and maintaining the highest level of professionalism, integrity, honesty and fairness.
PRINTED IN CANADA ARFAS0120/500