Post on 08-May-2018
Any parts missing or damaged must be reported to your supplierwithin 5 days of purchase. Please state size & colour of product and
part number as shown for the cor reponding size of door.
I N S P E C T D O O R B E F O R E F I T T I N G N O C L A I M S W I L L B E A C C E P T E DA F T E R T H E D O O R H A S B E E N I N S T A L L E D
Thank-you for choosing a MERLYN shower door.Please familiarise yourself with these instructions before installing.
Do you have all the tools required?
Is the installation site compatible with the size of door supplied?
Are all the enclosure components present?
Is the installation kit complete?
DO N O T attempt to install the product unless you can tick ALL 4 boxes
adjacent as satisfactory.
The wall plugs supplied with the installation kit are for use in solid walls.
Holl ow or ‘stud-partition' walls will require alternative �xings. Please
consult a hardware supplier for the correct type.
It may also be necessary to consult your tiling supplier about the correct
method for drilling your tiles.
< < M A J O R C O M P O N E N T S > >
F I T T I N G I N S T R U C T I O N S - F O L L O W S T E P S I N S E Q U E N C E
Ensure the shower tray is level in all directions and isproperly sealed to the w all. The wall must be tiled down tothe top edge of the tray. Do not angle out bottom tile.
1 Place �xed panel gasketV3211 onto bottom edgeof glass.
2 Loosen �xed glass panelclip.3 Place �xed glass panel into position on bottom r ail (with long
roller stops) & screw the frame together with screws V4111.Tighten �xed glass panel clip.
4
Power drill
6mm masonry drill bit
Pencil/marker
#2 Philips screwdriver
Spirit-level with horizontal & vertical level indicators
Tape measure
Safety eyewear
Quality silicone sealant & applicator
< < T O O L S Y O U W I L L N E E D > >< < F I T T I N G K I T > >
Repeat steps 2 to 4 for top rail to �nish frame.R ail with short roller stops is the top rai l .5
Fit handles V6107 to both doors.8
W A R N I N GH E A V Y P R O D U C T, A S S I S T A N C E M AY B E R E Q U I R E D
U S E S A F E T Y E Y E W E A R W H E N D R I L L I N G
I M P O R T A N T
Place door frame into position on top of shower tray ensuring entry space is in the correct position. Align frame into position, drill through pro�les atsimilar position to wall �xing screws and �x to wall pro�les with screws V4110, clips V2110 & snap-on caps V2109.7
Place both wall pro�les V1106 at 20mm from front edge of shower tray to outside edge of wall pro�le, wall �ange to inside, plumb, mark & drillholes. Fix both the wall pro�les into position with screws V4111, clips V2110 and caps V2109.2nd wall pro�le can be �tted into door frame when lifting onto tray in situations where the enclosure is a tight �t.
6
2 0m m
V11 06 x 2V 321 1 x 4
V 31 03 x 2
V 31 07 x 2
V 2101L x 1V 2101R x 1
V 2104 x 2
V 6107 x 2
V 2109 x 12V 2110 x 12
V 4110 x 6
V 6113 x 6
V 6115 x 1
V 4111 x 14
V 6103 x 2
A AB B
C
D
sizes 800 & 900 in 1 box • size 1000 in 2 boxes
Fitting Instructions Quadrant 2 Door
INSIDE TOP RAIL
24 HRS
Fit moving panels B into frame.9
Working from the outside. Press down on quick release rollers & insert intobottom rail. Fit chrome covers V6103 to inside of single rollers.
Press down on bottom rollers to gain easy access for cleaning11
Working from inside the enclosure set the doors into the top rail.Double rollers on top10
Press on cover caps V2104to wall profiles andV2101L/R to frame profiles.
14Ensure doors are closing correctly. MAIN ADJUSTMENT is made byloosening the top roller retaining screws and moving the glass panel upor down. When correct, secure screw. Micro-adjust with hexkey asshown. Door is correctly adjusted when top & bottom wheels hitroller stops evenly.
13 When doors are operating correctly & magneticseal is fully aligned proceed to sealing of unit.
Seal wall profile flanges to wall
on inside vertically. Seal bottom
rail to shower tray horizontally
on outside only. Seal upright
profile to wall from shower tray
approx 100mm vertically on
outside.
Seal all vertical joints on
bottom of frame on outside
only. Allow unit 24hrs to set.
15
Fit short, upright plastic seals V3103 on front of fixed panels & long seals, V3107on backs of moving panels. Ensure the bottom of the fixed panel seal V3103sits tight to the fixed glass panel clip.
Ensure sof t p last ic parts of sealsare fac ing each other.12
OUTSIDE
SEALINSIDEFLANGE
TO WALL
OUTSIDE BOTTOM RAIL INSIDE BOTTOM RAIL
MICRO-ADJUST WITH HEXKEY
OUTSIDE BOTTOM RAIL INSIDE TOP RAIL
NOTE POSITIONING FOR DOUBLE AND SINGLE ROLLERS
DOUBLE ROLLERS
SINGLE ROLLERS
LOOSEN SCREW
V9203 01/07
MOVE PANEL UP OR DOWN
Tel: +353 56 779 1555