End of Year ReportSecurityCenter

End of Year Report

•Topics Coveredo How to install the End

of Year report templateo How to modify the

report template to accurately report quarterly in an end of year report.

Install the Report Template

• Step 1 - From the reports page, select the report, and click Add. Next, select the Executive category, and choose “End of Year Report”

• Step 2 – Click “Add It Now”, and wait for 15 seconds for the report to be added. Next, click “Finish”.

• Step 3 – Delete the report, and then re-add the report to account for the chapter order bug.

Relative Date Changes• Components Requiring a Change

o Tableo Matrixo Bar Charto Pie Chart

• Settings to Changeo Cumulative

• Days Since Discovery (Vulnerability Discovered)o Mitigated Databases

• Days Since Mitigation (Vulnerability Mitigated)o Change the Relative Dateo Assuming Date the report will run is January 15, each

number must be increased by 15.

Change Matrix (Cumulative)• Step 1 – From the reports page, select the report and click “Edit”

• Step 2 – Click the Definition tab, then choose the Executive Summary Chapter. (Matrices are only in this chapter)

• Open the matrix and select a row by holding the mouse key while moving to right.

• Click Edit Filter, then go to Date Filters and change the “Vulnerability Discovered” dates.

Date Change Example• Day of Year Calculator

o http://www.mbari.org/staff/coletti/doytable.html

o Helps determine the number of days past January 1.

• Assuming the date the report is run were January 17, you would increase the numbers by 17.

o Between 288 days and 382 days ago.

• Assuming the date the report is run were February 23, you would increase the numbers by 54.

o Between 325 days and 419 days ago.

Change Matrix (Mitigated)• Step 1 – From the reports page, select the report and click “Edit”

• Step 2 – Click the Definition tab, then choose the Executive Summary Chapter. (Matrices are only in this chapter)

• Open the matrix and select a row by holding the mouse key while moving to right.

• Click Edit Filter, then go to Date Filters and change the “Vulnerability Mitigated” dates.

Change Table (Cumulative)

• Step 1 – From the reports page, select the report and click “Edit”. Navigate to the “Definition Tab”, choose a quarter chapter, and expand the section or group

• Step 2 – Click the “Edit” button next to the table.

• Step 3 – Click “Edit Filter”• Step 4 – Go to Date Filters and change the “Vulnerability Discovered” dates.

• Note that this will be required for cumulative table components only.

Change Table (Mitigated)

• Step 1 – From the reports page, select the report and click “Edit”. Navigate to the “Definition Tab”, choose a quarter chapter, and expand the section or group

• Step 2 – Click the “Edit” button next to the table.

• Step 3 – Click “Edit Filter”• Step 4 – Go to Date Filters and change the “Vulnerability Mitigated” dates.

• Note that this will be required for mitigated table components only.

Change Bar Chart (Cumulative)

• Step 1 – From the reports page, select the report and click “Edit”. Navigate to the “Definition Tab”, choose a quarter chapter, and expand the section or group

• Step 2 – Click the “Edit” button next to the Bar Chart

• Step 3 – Click “Edit Filter”• Step 4 – Go to Date Filters and change the “Vulnerability Discovered” dates.

• Note that this will be required for cumulative bar chart components only.

Change Bar Chart (Mitigated)

• Step 1 – From the reports page, select the report and click “Edit”. Navigate to the “Definition Tab”, choose a quarter chapter, and expand the section or group

• Step 2 – Click the “Edit” button next to the Bar Chart

• Step 3 – Click “Edit Filter”• Step 4 – Go to Date Filters and change

the “Vulnerability Mitigated” dates.• Note that this will be required for

mitigated bar chart components only.

Change Pie Chart (Mitigated)• Step 1 – From the reports page, select the

report and click “Edit”. Navigate to the “Definition Tab”, choose a quarter chapter, and expand the group after the “Remediated Vulnerabilities” section. These groups are the only ones with a pie chart.

• Step 2 – Click the “Edit” button next to the Bar Chart

• Step 3 – Click “Edit Filter”• Step 4 – Go to Date Filters and change the

“Vulnerability Mitigated” dates.• Note that this will be required for mitigated

pie chart components.

For Questions ContactCody Dumont

cdumont@tenable.com