Post on 09-Aug-2020
1
DOCUMENT
Open Competitive Bid (OCB)
For
Supply and Installation of Materials Testing and Processing Lab equipments of
Metallurgical & Materials Engineering Dept. at the three campuses of
Rajiv Gandhi University of Knowledge Technologies
Proprietary & Confidential
RAJIV GANDHI UNIVERSITY OF KNOWLEDGE TECHNOLOGIES
Ground Floor, Vindhya C4 Building, IIIT-H Campus, Gachibowli
HYDERABAD- 500 032
Phone: 040-23001830
2
Proprietary & Confidential
No part of this document can be reproduced in any form
or by any means, disclosed or distributed to any person
without the prior consent of RGUKT except to the extent
required for submitting bid and no more.
3
Contents
Description
Page No.
Newspaper advertisement 4
Time Schedule 5
Tender Form 6
Statement of important limits and values of bid 7-8
Eligibility Criteria 9-10
Requirement & Technical Specifications 11-17
Note 18
4
News paper advertisement
Short Tender Notice
RAJIV GANDHI UNIVERSITY OF KNOWLEDGE
TECHNOLOGIES
Ground Floor, Vindhya C4 Building, IIIT-H campus,
Gachibowli, HYDERABAD- 500 032
Phone: 040-23001830
Separate Sealed Tenders are hereby invited from reputed
Manufacturers or Authorised dealers for supply and installation of Lab equipments for the following labs of Metallurgical & Materials
Engineering Departments at the three campuses of RGUKT located at Basar (Adilabad District), Nuzvid(Krishna District) and RK Vally (YSR Kadapa District):
1) Chemical Metallurgy Laboratory 2) Physical Metallurgy Laboratory
3) Corrosion and Environmental Degradation Laboratory 4) Material Testing and Processing Laboratory
5) Heat Treatment Laboratory
Last date of submission of tender along with EMD as specified
in the bid document is on 09.08.2012 before 04 .00 pm.
Interested parties can collect the Tender document for
each laboratory from 25.07.2012 to 08.08.2012 against payment
of Rs. 5,000/- towards the cost of Tender document fee (non-
refundable) through D.D. from any Nationalized Bank payable
to REGISTRAR, RGUKT at Hyderabad from the office of the
RGUKT. For further details visit our website www.rgukt.in
Date: 25.07.2012 Sd/ Registrar
5
Time schedule of various Short tender related events
Bid calling date 25.07.2012
Last date for sale of
document
08.08.2012 at 05:00 P.M
Pre bid meeting 31.07.2012 at 11.00AM
Bid closing date/time 09.08.2012 at 04:00 P.M
Technical Bid Opening
date/time
13.08.2012 at 02:00 P.M.
Price Bid opening
date/time
14.08.2012 at 03:30 P.M
Bid Document fee Rs.5,000/-
Contact person Registrar, RGUKT
Reference No RGUKT/Proc/MME/MTPL/T 19/2012
Registrar,
RGUKT
6
TENDER FORM
Not transferable
Reference. No. RGUKT/Proc/ MME/MTPL/T 19/2012 Dated 25.07.2012
Subject: Invitation of Tenders for Supply, installation and commissioning of Materials Testing
and Processing Lab Equipments to the Metallurgical & Materials Engineering
Departments at three campuses of RGUKT located at Basara (Adilabad Dist), Nuzvid
(Krishna Dist) and RK Valley (YSR Kadapa Dist) of Andhra Pradesh.
Last date and time for submission of the TENDER AT RGUKT, Vindhya-C4, IIIT Campus, Gachibowli, HYDERABAD is 09.08.2012 up to 4:00PM
Dear Sir/Madam,
A. RGUKT invites sealed tenders comprising technical bid and price bid separately from reputed manufacturers (or) authorized dealers for three RGUKT IIITs located at Basara (Adilabad Dist), Nuzvid (Krishna Dist) and R K Valley (Kadapa Dist) of Andhra Pradesh.
B. The Tender form consists of 34 pages of which pages from 6 to 17 are instructions and
page No.25 contains the format for financial bid. The duly completed Technical Bid together with a copy of the bid document (this tender) signed on all pages by the Bidders authorized signatory and the Price Bid should be kept in separate sealed covers. These sealed covers must be submitted in a sealed master envelope super scribed
“Tender for Supply, Installation & Commissioning of Materials Testing and Processing Lab Equipments to the Metallurgical & Materials Engineering
Departments at the three campuses of RGUKT. The last date for submission of bid is 09.08.2012 and closing time is 04:00 PM.
C. The Sealed Tenders should be deposited in the Tender box kept in the office of Registrar, RGUKT, Hyderabad up to 04:00 P.M. on 09.08.2012.
For any clarification and further details on the above tender please contact by
Telephone No: 040-23001830 or Contact in Person during office hours.
Thanking you Yours faithfully,
Registrar, RGUKT.
7
STATEMENT OF IMPORTANT LIMITS/VALUES RELATED TO BID
Item Description
EMD Rs.1,00,000/- by way of Demand Draft from any
Nationalised Bank or by way of irrevocable bank
guarantee from any Nationalised Bank only. DD/BG
from other than Nationalised Banks will not be
accepted.
Bid Validity Period 365 days from the date of opening of Financial bid
EMD Validity Period 90 days from the date of opening of Financial bid
Warranty Period 3 years
Variation in quantities/number
of residents
+ 40 %
Period for furnishing
performance Security Deposit
Within 10 days from date of receipt of award
Delivery Schedule Bidder shall deliver the goods in one single lot within
30days from the date of award of the contract.
Performance security value 5% of contract value by way of irrevocable Bank
Guarantee from any Nationalised Bank
Performance security validity
period
38 months from award of contract ( including 30 days of
installation period)
Period for signing the order
Acceptance
Within 7 days from date of receipt of notification of
award
8
Payment terms
On delivery at user site
Payment for goods and services shall be made in Indian
rupees as follows.
1. 80% of payment will be paid after installation, commissioning
2. Balance 20% will be paid after 3 months after obtaining the satisfactory certificate from the Director, RGUKT IIITs.
Maximum Liquidated Damages
for late deliveries
For delays:- If the supplier fails to deliver any (or) all of
the goods or perform the services within the time period
specified in the contract the purchaser shall without
prejudice to its other remedies under the contract deduct
from the contract price as liquidated damages a sum
equivalent to 0.25% of the contract value per day until
actual delivery or performance up to a maximum
deduction of 10% of the delayed goods or services
contract price. Once the maximum deduction is reached,
the purchaser may consider the termination of the
contract duly forfeiting the performance security etc.,
9
ELIGIBILITY CRITERIA
1. This bid is open to all firms within India who are eligible to do business
under relevant Indian laws as in force at the time of bidding, subject to meeting the pre-qualification criterion. They should provide list of customers
of previous supply of similar/ same items to IITs, NIT’s or Central Universities or any Academic Institute of National repute with contact details. Copies of orders received from the reputed firms on bidding firm
need to be submitted. 2. The bidder should have servicing facility or work shop with in India so the
provision of service is possible at a short notice and without incurrence of delay.
3. The Bidding firm should have minimum turnover as follows:
Bid Value offered against
the tender call
Last financial year’s business
turnover
25 lakhs 50 lakhs
50 lakhs 1 crore
50-100 lakhs 2 corers
Greater than 100 lakhs 3 Crores
The bidder should have adequate experience in supply of such materials/ equipment as
required in the tender. Bidder should furnish proof of having supplied such materials as
required in the tender in the previous financial year ending 31st March 2012 as mentioned
above . A certificate of the bidder’s turnover in Rupees must be enclosed and be duly certified
by a firm of charted accountants. In this certificate the turnover of subject material during 2011-
2012 (ending with 31.03.2012) must be covered.
4. The bidder should furnish satisfactory performance certificate from the parties
concerned to whom bulk supplies were effected, in case such supplies were made.
RGUKT may contact any such parties to elicit details.
5. Bidder should be registered under VAT Act/CST Act with the relevant State Sales
Tax Authorities. He should furnish along with the bid document, the relevant
VAT/CST Registration Document and PAN / TAN Card copies.
6. All bidders shall also include the following information and documents with their
tenders ( in the Technical bid cover)
a) Copies of original documents defining the constitution or legal status, place of registration, and principal place of business of the bidding
10
firm/entity; written power of attorney of the signatory of the Bid to commit the Bidder.
b) Machinery/equipment owned by the bidder and number of employees.
c) Latest Income Tax returns and VAT/ CST Returns filed.
d) List of Present Clientele with contact addresses & telephone numbers.
7. All the certificates furnished along with technical bids should be attested by a
Gazetted Officer, counter signed by bidder along with their seal.
The bidders must submit all relevant documentary evidence in support to
their claim for eligibility in placing bid. The tenders received without the
above documents will be rejected.
11
Requirement of Materials Testing and Processing Lab Equipments
S.No Item Total qty
required 1 Brinell Hardness Tester 03
2 Charpy/Izod Impact tester 03
3 Fully Automatic Micro- hardness tester
03
4 Portable/ Laboratory Induction Melting Furnace 03
5 Laboratory double headed rolling mill
03
6 Digital Motorized Rockwell Hardness Tester
03
7 Notch cutter for Charpy Impact specimen 03
8 Computerised Vickers Hardness Tester 03
1. BRINELL HARDNESS TESTER
1. Brinell Hardness Tester for direct and accurate measurement of BrinellHardness
Number. The tester must have wide testing range for soft to hard materials. High
accuracy and reproducibility of measurements at all loads should be provided.
2. Test Load Range : 500kgf to 3000kgf
Max. Test Height : 410mm
Scale least Count : 0.01mm
Throat depth : 200mm
Testing table : 200mm (1 No.) and anvils
:70 mm dia with "V" groove for round specimens of 10 to 80 mm dia (1 No.)
Ball indenter holder for 5 mm dia. Ball :1 No.
Ball indenter holder for 10 mm dia.ball :1 No.
Ball indenter WC ball 10mm dia.
Calibrated Standard Test Block for 5mm dia. Ball indenter and 500 kgfload :1 No.
Calibrated Standard Test Block for 10mm dia. Ball indenter and 3000 kgf load :1 No.
12
• The unit must includeOperating instruction and maintenance manual (1 No. each),
• Spares: Microscope bulbs (12 No.), Fuses: (6 No.), Brinell Indenters (1 each of 5 mm
and 10 mm dia (steel and WC)), standard test blocks and other consumables.
• Provision for easy and accurate reading of impression dimensions
• The equipment must be calibrated to give accurate and reproducible results.
Supplier has to prove that the machine is in calibration at the time of installation.
• Any additional feature (s) may be quoted separately by the bidder. This should not
be the part of price of the unit.
• Relevant complete tool kit: 1 set.
• Do not quote/bid for combined Brinell/Rockwell machine or any other combination. It
should be straight Brinell only.
2. Specification of Charpy/Izod Impact tester
Impact Energy 300J
Scale Range and Division Value of Scale Disk 0-300J the division value of each grid is 2J
Distance between Axis of Pendulum Shaft and
Striking Center 750mm
Maximal Impact Speed 5.24m/s
Span of Test Sample Support 40 +0.2mm
Radius of Circular Arc in the End Part of the
Test Sample Support
R1.25mm
Radius of Circular Arc of Impact Blade R2-2.5mm,R8mm
Included Angle of Impact Cutter 30°±1
Thickness of Impact Cutter 16 mm
Specification of Test Sample 10×10×55 mm or 10x10x75
Precision of Force Transducer ≤±1%FS
Resolution of Angular Displacement
Transducer
0.1°
3.Fully Automatic Micro- hardness tester
a) Load range – 10 g to 1000g ( optional 2 gms to 3000 gms)
b) Duel time 5 – 99 sec
c) Automatic loading and releasing
d) Microscope Magnification – 100 x , 400 x
13
e) Measurement of indentation – Digital Fillar eyepiece
f) Max. measurement length – 175 microns
g) Max. Height of specimen – 65 mm
h) Max. Depth of specimen – 85 mm
i) LCD touch screen
j) Auto-turretting, Auto – load selection, Auto motorized x-y motion and Motorized Z motion
k) Manual over riding option to all the automations for any in- service failure
l) Computer interface for single as well multiple indentation measurement and direct plotting the hardness graph / profile .Programming the profile in straight and also zig-zag way.
m) Power Supply - AC 230 V
4. Portable/ Laboratory Induction Melting Furnace
Shall have Fully automatic control. Automatic power regulation. PID controller for temperature and digital temperature indicator Feather touch controls. Simple in operation. All safety precautions provided. Lower power consumption. Reduced metal loss on remelting Continuous melting of metal with chilling plant provided Perfect mixing of alloys due to auto stirring
Technical Specifications:
Power Supply Three Phase
Voltage 415v 50Hz
Absorbed Power Up to 15 kw
Capacity of Crucible 5 Kg of liquid Copper
Maximum Temperature Ability to melt both ferrous and nonferrous metals
Melting Time 20-30 min.
Temperature Measurement Digital/ Thermocouple type
Cooling Water Temperature 20 to 35 degree
14
Water Pressure 4 Bar
Maximum Water Flow Commensurate with cooling requirements
Chilling Unit Capacity As required
5. Laboratory double headed rolling mill
Features
Double headed Unit to facilitate rolling of sheet on one side and rod rolling on
the other.
Chilled cast iron rolls of high surface hardness
Adjustable Screw down mechanism to keep the roll gap constant during
rolling
Gear box coupled with suitable pinion drive to transfer the drive from motor
to the rolls
Gears made of EN24
Lubricated gear drive to eliminate the friction and noise
Technical specifications 1. Roll width : >150 mm
2. Roll diameter : 75- 101 mm
3. Wire groves : 0.71 to 12 mm
4. Maximum sheet width that can be rolled : 150 mm
5. Rolls made of : Case hardened High carbon chromium steel
6. No of half round grooves : 2
7. Roll speed : One or two fixed speeds
8. Lubricating system : Automatic
9. Power input supply : 3-Phase AC 50Hz
10. Power rating : 4 to 6 H P
6.Technical specifications of Notch cutter for Charpy Impact specimen
1. Specimen size: 10×10(7.5 or 5)× 55mm
2. Notch type:V: depth 2mm, 45º±2, r=0.25mm±0.025mm
U2: depth 2mm, width 2mm, r=1mm±0.05mm
U3: depth 3mm, width 2mm, r=1mm±0.05mm
15
U5:depth 5mm, width 2mm r=1mm±0.05mm
3. Broacher travel:340±10mm
4. Speed:2-3m/min
5. Lubrication system: lubricating oil circulation, oil is adjustable
6. Power requirements:3-phase, 5-line, AC 380V±10%, 50Hz
Remark: Broacher (notch blade) has to be ordered by customer.
7.SPECIFICATIONS OF DIGITAL MOTORISED ROCKWELL HARDNESS TESTER
• Motorized automatic operating cycle of loading/dwell/unloading.
• Preliminary Test Force (Load) - 98.07N (10kgf)
• Total Test Force (Load) - 588.4, 980.7, 1471N (60, 100, 150 kgf)
• Test Load Selection: Motorized as well as manual.
• Automatic weight selection and automatic zero setting gauge for very soft to very
hard materials.
• Set position with LED bar indicator.
• Option to override the motorized testing and do the test entirely manually should be
available.
• Large size scale display for reading with 0.1 Rockwell hardness number Resolution.
• Parallel output for connecting printer to get results indicating serial number of tests,
load, hardness scale, hardness value and high / good / low indication.
• Operating Instruction and maintenance manuals must be provided.
• Spares: Indenters for all Rockwell scales (2 No. each), standard test blocks and
other consumables.
• The equipment must be calibrated to give accurate and reproducible results.
• Any additional feature (s) may be quoted separately by the bidder. This should not
be the part of price of the unit.
8.COMPUTERISED VICKERS HARDNESS TESTER
1. Computerized Vickers Hardness Tester for direct and accurate measurement of
Vickers Hardness Number using image processing technology. The tester must have
wide testing range of measuring hardness of very soft to very hard materials. The
tester must have motorized loading/dwell/unloading cycle. High accuracy and
reproducibility of measurements at all loads should be provided. The test loads
required are 5kgf, 10kgf, 20kgf, 30kgf, 50kgf….to 320kgf.
2. Max test height: 200mm, and throat depth: 135mm
16
3. The tester must have the latest features viz. user friendly software with all help files
and window features, online indentation setting and focusing on PC monitor &
advanced image processing. It must have statistical evaluation software for
calculating standard deviation, mode, median, and showing pictorial results e.g.
histogram etc.
4. Impression image viewing and recording facility must be available with the tester.
5. Facility of manual operation must be available.
6. The equipment offered must be complete with the following:-
Calibrated Standard Test Block (1 No.), Diamond indenter (1 No.), Flat Anvil (1No.),
Vee-type Anvil –small & big (1 No. each), Relevant Spanners Set (tool kit), Electric
Cord & PC interface cord (1 No. each), Video Capture software CD (1 No.), Operating
instruction and maintenance manual (1 No. each),
7. Spares: Microscope bulbs (12 No.), Fuses (12 No.), Vickers Indenter (3 No.),
standard test blocks and other consumables.
8. Accessories: PC with latest configuration suitable for above hardness tester with all
attachments, preferably with color monitor, color printer and all other necessary
accessories needed for smooth testing of samples.
9. The equipment must be calibrated to give accurate and reproducible results.
Supplier has to prove that the machine is in calibration at the time of installation.
10. Any additional feature (s) may be quoted separately by the bidder. This should not
be the part of price of the unit
7. General Requirements & Qualification Criteria
Bidding Firm offering the product should have ISO 9001 Accreditation
certification.
Bidding Firm, offering the product, should have supplied similar type of test
systems for a several years to Government establishments, defense organizations
& National higher learning institutions like IITs, IISC etc., in India
Bidding Firm offering the product should submit list of supplies made by it,
during last two years with complete contact details of the end users such as
phone number, fax number, e-mail ID etc. It should submit copies of order placed
by such organizations and user certificates for goods of same/similar nature.
17
Bidding Firm offering the Product should have a Local Service Support Facility,
preferably in Hyderabad, and should submit address and contact details
Bidding Firm should give an Undertaking that, un interrupted service support will
be given for a minimum period of 10 years with unbroken availability of spares
supply.
Bidding Firm should give an undertaking that, the Software upgrades if any,
during the warranty period of three year, should be supplied free of charge
Bidding Firm should offer pre-dispatch inspection free of charge at their factory
premises for 2 users for 3 days and post installation training at our three
laboratories in different campuses to 2 users for 5 days.
18
NOTE
A complete set of bidding documents may be purchased by interested bidders from the
RGUKT contact person upon payment of the bid document price which is non-refundable.
Payment of bid document price should be by demand draft/ cashier’s cheque or certified
cheque drawn in favour of “Registrar, Rajiv Gandhi University of Knowledge Technologies”
and payable at Hyderabad (India).