Diy Plywood Floors

http://www.instructables.com/id/DIY-PLYWOOD-FLOORS/

Food Living Outside Play Technology Workshop

DIY PLYWOOD FLOORSby jdfnola on December 30, 2011

Table of Contents

DIY PLYWOOD FLOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Intro: DIY PLYWOOD FLOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 1: Tools & Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2: Rip Out The Old Carpet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 3: Clean The Subfloor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 4: Apply Kilz To Seal And Protect The Sub-Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Step 5: Install The Plywood Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Step 6: Doorways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Step 7: Add Molding (If Needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Step 8: Apply Polyurethane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Step 9: Finished Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Intro: DIY PLYWOOD FLOORSI love my house. It's a classic New Orleans shotgun. Over 100 years old, it was made by craftsmen who really knew how to build things to last. There was an addition(back bedroom and bathroom) put on when the house was refurbished shortly before Hurricane Katrina. The addition was built competently, but they used pretty cheapmaterials on things like the doors, trim, bathroom fixtures, etc. In most of the house we have nice, solid hardwood floors. In the back bedroom - carpet. Ugly, dirty, Berbercarpet. We hated it.

In a fit of annoyance we decided to ditch it. The problem was we needed to do it on the cheap.

My first thought was to rip out the carpet and sand, then paint the subfloor and leave it like that until we had enough to put in hardwood floors that matched the rest of thehouse. The downside to this is that there is nothing between you and the ground and without any protection other than the paint you might damage the subfloor and needto replace it (not something I wanted to do).

The other idea I had was to lay down plywood over the subfloor and paint/finish the plywood. I'd seen this in some lofts and thought it looked pretty good. This is what wedecided to do.

We had two simple goals - put something in that looked better than the ugly carpet and for as little as possible. I think we definitely achieved this and the total cost around$400.00.

The best thing a about doing your floors like this is that down the road if you want to upgrade and install hardwood floors you don't need to pull up anything - you caninstall them right on top.

Step 1: Tools & MaterialsTools you will need:

• Pry-bar.• Shop Knife• Measuring tools -Tape Measure, Steel Square, etc.• Circular Saw with blade for cutting plywood.• Hammer.• Caulk Gun.• Paint brushes or paint roller.• Polyurethane applicator.

Materials• Kilz Primer• Painters tape• Cabinet Grade Plywood Sheets (we used 4'x8' 5MM hardwood at around $11.00/sheet).• Oil Based Polyurethane (we used Varathane Clear Oil based Polyurethane).• Construction adhesive (we used OSI brand that was specifically for subfloors).• Finishing Nails (long enough to go through the plywood and into the subfloor).

You might also need:Additional floor molding. When you take up the carpet there might be a space between the floor and the molding. We used quarter round shoe molding which matchedthe rest of our house.

NOTES:

You don't need a big caulk gun - just use the regular kind or you will wear out your hands.

Make sure you use an oil based polyurethene made specifically for flooring. The oil based poly brings out the color of the wood and the grain and makes the plywood look"warmer". It's almost like putting on a mild stain.

There are lots of other choices you could make on the plywood. The thing you want to do is make sure it is hardwood and "cabinet grade". We chose the cheapest that fitthe criteria but you could spend a bit more and get oak, birch, etc.) It does not need to be thick (we used 5MM). I will say the plywood we got (http://tinyurl.com/77r6rzs )looked as good as the birch and was much cheaper.

Image Notes1. 5MM Hardwood Plywood (back side)

Step 2: Rip Out The Old CarpetFirst thing you will need to do is move everything out of the room. This project takes some time, you can't do it in a day. You need to allow for drying time in yourplanning. We were out of this room for around 3 weeks.

To rip up the carpet just cut into it with a shop knife and start pulling. The carpet will come up and underneath will be a carpet pad which is glued on and also must beripped out.

Once the carpet and the carpet pad are up you will be left the wood and nails that the carpet was attached to. This will be ringed around the entire room. It's a pain to pullup. You will need to use the pry-bar and be careful not to damage the molding.

Image Notes1. Yuck!

Image Notes1. More Yuck!

Image Notes1. Carpet ripped from the nails that run around the room

Image Notes1. Carpet almost off, revealing the cad below it

Step 3: Clean The SubfloorThere will be lot's of dust and denis left over from tearing up the carpet. You will need to sweep and vacuum it up. The carpet pad that was glued on might have left somepatches on the floor which you will need to scape off.

Once it's all swept up and vacuumed, mop the subfloor to clean it and let it dry.

Image Notes1. Sub floor swept and vacumed2. Sub floor swept and vacumed

Image Notes1. Mopped subfloor. All carped debris removed.

Image Notes1. Helping the closet subfloor dry.

Step 4: Apply Kilz To Seal And Protect The Sub-FloorApply the Kilz sealant to the subfloor. The Kilz will help protect the subfloor and help seal in any odors that have made it on to the subfloor.

Step 5: Install The Plywood FloorWe started in the closet s a test. If you need to cut the plywood to fit the space, place the edges you cut towards the edge of the wall as the cuts you make will not be asstraight and clean as the factory edges.

Once you have made your cuts lay down the plywood sheets the way you want them as a test. If everything looks right you are ready to attach the plywood to thesubfloor.

Use the construction adhesive on the liberally on the "bad" side of the plywood (the side without the nice woodgrain). Once glued set the plywood on the subfloor and nailit down. I used a lot of nails as I wanted it to be solidly affixed and I did not want to have to wait for the glue to dry to lay down more sheets.

First I nailed down the corners and placed a nail in the middle.Then I placed the nails in columns that ran down the lenght of the sheet, each collumn of nails abound 4-6in from the next. I did not measure, I just eyeballed it.

I put down the plywood in sheets running longwise next to each other. There was a small strip on one side of one wall that required me to cut lengths of plywood (about 4in" wide stops of 8').

At the end of the room I had to cut the plywood to fit. The pictures show all of this.

Image Notes1. Installing first sheet in the closet.

http://www.instructables.com/id/DIY-PLYWOOD-FLOORS/Image Notes

1. Closet done! Looking good.

Image Notes1. First sheets installed tight to one wall.

Image Notes1. Will need to cut strips to fill this gap.

Image Notes1. First row of sheets installed.

Image Notes1. Second row of sheets installed

Image Notes1. Last row of sheets needs to be cut short to fit space-remember to put the cutside to the wall

Image Notes1. Last of the short pieces to be installed.

Image Notes1. Will fill in with cut strips

Image Notes1. Strips installed along the one wall.

Image Notes1. Not too bad!

Image Notes1. All of the main floor installed and with trim pieces.

Step 6: DoorwaysThe gap where the doorway is between the rooms is tricky. The floors between the rooms may not be level or made out of the same material and the gap will probablynot be square.

Lay down strips of plywood to build up the gap in the doorway. Once it is relatively level you can put a "cap" strip that bridges the two floors.

The most important thing I can say here is that you will need to improvise. It took me a while to get these to my liking and I ripped up my work and started from scratch onone of them.

Image Notes1. Note: the bridge is not square. That's because the house is not square.

Step 7: Add Molding (If Needed)Now that the floor is down, you can add any trim molding that is needed. I used 1/4 round shoe molding.

This filled the gap between the rest of the molding and the wall. I used the same finishing nails I used on the floor. Then I taped up the floor and painted the molding.

Step 8: Apply PolyurethaneTo seal the floors follow the directions on the polyurethane. I purchased an applicator so I could do it faster - definitely recommended.

We used four coats and it took a day between each coat.

Image Notes1. Get yourself one of these and save your back.

Step 9: Finished ProductAfter the floors dry you can bring your stuff back in and your done.

Related Instructables

How to install ahardwood floor.by mattl

"Augusto"Workshop~MarcosDavidson,MelbourneAustralia.(Photos) byMelbourneseMarcos

Howto Make aSunken Showerwith HeatedTiles bySenseless

Sand andrefinish yourhardwood floorswith aconverted floorpolisher bytewharau

StudioMonitor SpeakerStands byddjack59

modernouthouse bycoolbeansbaby68

Comments

3 comments Add Comment

jdege says: Jan 1, 2012. 5:11 AM REPLYI always replace the molding after I've finished the floor. I find it a lot easier to touch up the paint on the molding, than to apply the floor finish right up to theedge, cleanly.

l8nite says: Dec 31, 2011. 10:18 PM REPLYThat looks great ! A friend did kind of the same thing in his studio but he cut the plywood into 2x2' squares, rotating the panels as they went down to changethe grain direction, no nails, he just glued and weighted each panel down. It's a great floor to walk on and because it was so inexpensive he doesn't worry asmuch about getting paint or other materials on it. Thank you for sharing your project

jdfnola says: Jan 1, 2012. 12:49 AM REPLYGlad you liked it. I thought about doing just what your friend did but I was worried that my poor cuts on the circular saw would make for problems at theseams.

Diy Plywood Floors

Documents

Transcript of Diy Plywood Floors

SUPERIOR HARDWOOD FLOORING, SUPERIOR ENGINEERED … · For wood sub-floors, hardwood flooring must be installed on plywood or OSB over joists. If the existing sub floor consists of

American Plywood Association - Plywood Planbook - 1980

Birch Plywood Birch Plywood - Lathams

Plywood Calculator …...woodworking plywood prices lumber building project how to DIY easy simple chart calculator estimate Created Date 3/28/2012 1:59:43 PM ...

Product Guide: Sanded Plywood - Murphy Plywoodmurphyplywood.com/pdfs/softwood/APA_Sanded_Plywood_Guide.pdf · product guide Sanded Plywood. ... Typical APA sanded plywood trademarks

the builder’s guide to plywood. · • Michael Jewitt’s DIY Wood Cookbook 1. ... moisture levels ... ability to balance fluctuations in temperature and humidity,

Home-made DIY e-Drumskenstuff.weebly.com/.../home-made_diy_e-drums.pdf · Home-made DIY e-Drums These e-drums are pretty simple to make from MDF and/or plywood, inexpensive wooden

A W · 2c Hardwood Floor Installation (S-18 Break Room ): Remove and discard the existing plywood floors; install hardwood – laminated plywood, 20 mm thick. M2 26 - 2.d Parquet

Plywood Technical Data Sheet for PSF Plywood

Water Resistant Plywood by Evergreen Plywood Industries Yamunanagar

A.W. GRAHAM LUMBER, LLC...• Sides are 1/2” plywood and 3/8” plywood floors. Interior parts are laminated to provide a smooth, durable interior. Finished Ends: • Finished ends

FINNFOREST PLYWOOD - Jular · concrete shuttering plywood. It can be easily machined and is as easy to fix as standard birch plywood. FINNFOREST DIAMOND PLYWOOD is a birch plywood,

form flooring report 080415 rev1 - Parkay Floors€¦ · Ceiling Concentration (2014) Particle Board Plywood Thin Medium Density Fiberboard (MDF) Medium Density Fiberboard (MDF) Particle

2011 easy cruising - tashoot.co.il...SOLID > PLYWOOD FLOOR economical + simple to use Solid floors – peace of mind guaranteed! Its plywood-board system, with its proven toughness,

Architectural Guidelines - Zendesk · floors with plywood deck or concrete alternative. Timber closed tread staircase with timber painted balustrades and handrails. The Association

LIFETIME FLOORS BAMBOO FLOORING · LIFETIME FLOORS BAMBOO FLOORING ... Subfloor panels should conform to U.S. Voluntary Product Standard PS1-95, Construction and Industrial Plywood

Balaji Timber & Plywood, Chandigarh, Timbers and Plywood

DIY CLOSET - storage.googleapis.com€¦ · DIY CLOSET Learn how to make a dressing station that provides more storage for clothes I bought a 4’ by 8’ sheet of 3/4” thick plywood

Indian plywood industries - INDIANA PLYWOOD · INDIANA Plywood Industries Company Profile Background Established in the year 1996, INDIANA PLYWOOD INDUSTRIES is one of the most trusted

Mr plywood also known as commercial plywood