Post on 03-Jul-2020
de
CrystalWork StarterKitCrystalWork StarterKit | Kit de démarrage CrystalWork
2
You can find further information at:
www.bernina.com
3
CrystalWork StarterKit en | 4
CrystalWork StarterKit de | 6
Language
4
en
This starter kit contains the material to make templates for crystal designs which have been designed by BERNINA DesignWorks.
To create these design templates you need a BERNINA sewing machine with embroidery func-tion plus the BERNINA CrystalWork Tool.
Your individually created crystal designs can be fixed on almost all heat-resistant textile fabrics or accessories.
To ensure your safety › Please read the instruction manual of the sewing machine, of the CrystalWork Tool and this
accessory carefully before use!
Preparing the embroidery hoop › Position the carrier paper on the inner
hoop (1). › Make sure that the coated side of the paper
points upwards. › Move the opened outer hoop over the paper
and push downwards. › Hoop the carrier paper very tautly (2). › Cut back excess paper. › Mark the center of the hoop. › Cut the template material to size according
to the size of the design (3). › Position the template material in the center
of the hoop (4).
WARNING
Crystals can be swallowed by child-ren! › Do not let children play with the
material unattended.
Tip!Using the DesignWorks software suite you can print the
design in its original size. Use the print as a pattern.
1 Instruction manual2 Template material 415 mm x 317 mm2 Iron-on foil 415 mm x 315 mm1 Brush1 Bag with crystals SS10
43
1 2
Contents
Application
Preparing
Additionally required
cardboard
carrier paper
Use Reynolds Freezer Paper or customary baking or greaseproof
paper, as wide as possible from a roll.
5
en
Punching the template › Punch the CrystalWork template using your
sewing machine (5). › Remove the template from the carrier
paper (6). › Stick the finished template on a piece of
cardboard (7).
Filling in the crystals › Brush the crystals in circular motions into
all the punch holes (8). › Make sure that the shiny side of the crystals
points upwards (9).
Preparing the iron-on foil › Cut the iron-on foil to size according to the
size of the template. › Position the iron-on foil over the crystals
and press down firmly (10). › Remove the iron-on foil with the Crystal-
Work Design carefully. Make sure that all the crystals remain sticking to the foil (11).
Ironing on crystals › Adjust the heat of the iron according to the
fabric. › Position the design as desired. › Make sure that the iron is dry. › Press on for about 20 sec (12). The duration
of the ironing time depends on the tempe-rature of the iron.
› Check whether all the crystals have been fixed.
› Remove the iron-on foil slowly (13).
Tip!Wash and dry clothes with crystals inside out.
5 6
7
8 9
10
12
11
13
Mode of operation
6
de
Stickrahmen vorbereiten › Trägerpapier auf den inneren Stickrahmen
legen (1). › Darauf achten, dass die beschichtete Papier-
seite nach oben zeigt. › Geöffneten, äusseren Stickrahmen darüber
schieben und nach unten pressen. › Trägerpapier sehr straff in den Stickrahmen
einspannen (2). › Überstehendes Papier zurückschneiden. › Stickrahmen-Mitte markieren. › Schablonenmaterial entsprechend der Muster-
grösse zuschneiden (3). › Schablonenmaterial mittig auf dem
bespannten Stickrahmen platzieren (4).
Tipp! Mit der DesignWorks Software Suite einen Ausdruck des
Musters in Originalgrösse erstellen und als Schnittvorla-
ge verwenden.
Dieses StarterKit enthält das Material, um Schablonen für Strassstein-Muster anzufertigen, die mit der BERNINA DesignWorks Software Suite entworfen wurden.
Zur Herstellung dieser Musterschablonen benötigen Sie eine BERNINA Stickmaschine und das BERNINA CrystalWork Tool.
Ihre individuell angefertigten Strassstein-Kreationen können anschliessend auf fast allen wär-mebeständigen Textilien oder Accessoires fixiert werden.
Zu Ihrer Sicherheit › Vor Gebrauch die Bedienungsanleitung der Stickmaschine, des CrystalWork Tools und dieses
Zubehörs sorgfältig lesen!
WARNUNG
Strasssteine können von Kindern verschluckt werden! › Kinder nicht unbeaufsichtigt mit den
Materialien spielen lassen!
2 Schablonenmaterial 415 mm x 317 mm2 Bügelfolie 415 mm x 315 mm1 Bürste1 Beutel mit Strasssteinen SS101 Bedienungsanleitung
Vorbereiten
Anwendung
Lieferumfang
43
1 2
Zusatzmaterial
KartonTrägerpapier
Reynolds Freezer Paper oder handelsübliches, breites Backpapier von
der Rolle verwenden.
7
de
Schablone stanzen › Strassstein-Schablone mit der Stickmaschi-
ne stanzen (5). › Schablone vom Trägerpapier lösen (6). › Fertige Schablone auf Karton kleben (7).
Strasssteine einfüllen › Mit kreisförmigen Bewegungen Strassstei-
ne in alle Stanzlöcher bürsten (8). › Sicherstellen, dass alle Strasssteine mit der
glänzenden Seite nach oben liegen (9).
Bügelfolie vorbereiten › Bügelfolie entsprechend der Schablonen-
grösse zuschneiden. › Bügelfolie über die Strasssteine legen und
gut andrücken (10). › Bügelfolie mit Strassstein-Muster vorsichtig
abziehen. Hierbei darauf achten, dass alle Steine an der Folie haften bleiben (11).
Strasssteine aufbügeln › Die Bügeltemperatur dem Stoff entspre-
chend einstellen. › Bügelfolie mit Strassstein-Muster auf
gewünschter Oberfläche platzieren. › Mit einem trockenen Bügeleisen etwa
20 Sekunden festdrücken (12). Die Anpress-zeit variiert je nach Bügeltemperatur.
› Kontrollieren, ob alle Strasssteine fixiert wurden.
› Bügelfolie langsam abziehen (13).
Tipp!Kleidungstücke mit Strasssteinen vor dem Waschen und
Trocknen auf Links wenden.
Arbeitsweise
5 6
7
8 9
10 11
12 13
de
© Copyright by BERNINA International AG 034312.51.01 2013|6
CrystalWork StarterKit | Kit de démarrage CrystalWork | CrystalWork startutstyr | CrystalWork aloituspakkaus | CrystalWork Стартовый комплект | クリスタルワーク スターターキット