Post on 12-Mar-2018
®
Collet Chucksand ColletsFrom the world’s number onename in workholding
1
Call 1-800-338-0027
® Power Collet Chucks
For accurate, high-volume turning of bar stock or other parts under3-1/8” in diameter, your best bet is a collet chuck. Why?
■ Consistent centering. Collet chucks grip the workpiece aroundthe entire circumference, with no slippage when the stock is re-gripped, and less risk of deformation to thin-walled workpieces.
■ Better tool clearance. Short or thin parts can be machined closer to the chuck face for better accuracy and less distortion.
■ Higher speeds. Compact, lightweight collet chucks have agreater tolerance for high centrifugal forces, hold their grippingforce more consistently, and reduce the load on machine spindlebearings.
■ Longer life. In high-volume production, collet chucks haveproven to have a consistently longer service life than 3-jawchucks.
Riten Collet Chucks are precision ground with guaranteed repeata-bility of .0002” TIR. Tolerances are held uniformly from the mountingto the working collet taper.
Riten offers three basic types of power collet chucks:
1. Pullback. Simple, one-piece design used on standard lathes.
2. Set Length. Used where precise pick-off is required. Little or noaxial part movement.
3. Setrite®. Set length chuck with ultra-fine four-screw adjustmentfeature. The most accurate chuck in the metalworking industry.
Our set length series includes special short-profile models using theversatile Multibore collet, and three labor-saving quick changechucks with pre-loadable bayonet caps.
NOTE: All collet chucks require a drawtube adapter to fit specificmachines. See page 24 for specifications.
Collet Chucks or 3-Jaw?
The Riten Selection
Dead length chuck withSetrite® adjustment
Multibore standard chuck
Quick change chuck
2
www.riten.com
Riten size-for-size collets (5C, 16C and R8) are designed for excellentaccuracy and repeatability, superior gripping power, and extendedservice life. To achieve this, we load the collet with a coil at the baseof the slots, heat the collet to a glowing red, insert the spreader intothe slots, and push down on the collet face. After cooling for one totwo minutes, the spreader is removed and the collet cools complete-ly. This process gives our collets a spring of .010” and drasticallyimproves the life of the collet. Few other manufacturers go to thislength to ensure a quality collet.
You’ll also find Riten collets are easier to attach, because we mill offthe thin top edge of the threads to prevent binding in the radius ofthe female thread.
For bar work, the Multibore collet gives you great flexibility. Just 12collets provide every size for 1/8” to 3-1/8”. Multibores are segment-ed to close parallel for uniform gripping on undersize or oversizebars, with no marring of the finished parts.
For second operation, the B Type Spring Collets are ideally suitedfor short gripping with both Multibore and Quick Change powerchucks.
This catalog displays our full line of collets and chucks, most of whichare in stock for quick delivery. Special designs are available onrequest.
If you have questions, call our Technical Service people at 800-338-0027, or visit us online at www.riten.com.
® Collets
Unique Manufacturing Process
Special Models
Size-for-size collets(5C, 16C and R8)
Multibore collets
B Type Spring collets
3
Call 1-800-338-0027
Setrite® Set Length . . . . . . . . . . . . . . . . 45C, 16C Collet Chucks• Setrite® feature allows accuracy
adjustment to virtual zero• Accepts 5C and 16C collets• Type A and DIN mounts
Set Length Standard5C, 16C Collet Chucks . . . . . . . . . . . . . . 5• Short overall length ideal for main
or sub-spindle work• Accepts 5C and 16C collets• Type A and DIN mounts
5C, 16C Collet Chucks . . . . . . . . . . . . . . 6• Standard pullback operation• Accepts 5C and 16C collets• Type A and DIN mounts
Multibore Standard Collet Chucks . . . . 7• Set length operation• Ideal for second operation work• Accepts DIN type Multibore & spring collets• Type A mount
Multibore Short Collet Chucks . . . . . . . 8• Set length operation• Ideal for bar work with minimum working envelope• Accepts Multibore collets only• Type A mount
Quick Change Collet Chucks, Type A . . 9• Faster collet changes• Set length operation• Ideal for bar or secondary work• Accepts DIN type Multibore & spring collets• Type A mount
Quick Change Collet Chucks, DIN . . . .10• Faster collet changes• Set length operation• Ideal for bar or secondary work• Accepts DIN type Multibore & spring collets• Recess DIN 6353 mount
Quick Change Collet Chucks, Short.. . 11• Faster collet changes• Set length operation• Short length maximizes work envelope• Ideal for bar work• Accepts standard & DIN Multibore collets• Type A mount
Page
® Product Index
R8 Collets . . . . . . . . . . . . . . . . . . . . 12Diameters up to 27/32” and 20mm
5C Collets (inch). . . . . . . . . . . . . . . .135C Collets (Metric) . . . . . . . . . . . . . 14Diameters up to 1-1/8” and 27mm
16C Collets (inch) . . . . . . . . . . . . . . 1516C Collets (Metric) . . . . . . . . . . . . 16Diameters up to 1-5/8” and 42.5mm
Multibore Collets, Plain Bore. . . . . 17Diameters up to 3-1/8” (79.37mm)
Multibore Collets, Heavy Duty. . . . 18Diameters up to 3.07” (78mm)
Multibore Collets, DIN 6343 . . . . . . 19(Serrated Bore)Diameters up to 3.14” (80mm)
B-42 Spring Collets (inch). . . . . . . 20B-42 Spring Collets (Metric). . . . . . 21Diameters up to 1-5/8” and 42.5mm
B-60 Spring Collets (inch) . . . . . . . 22B-60 Spring Collets (Metric). . . . . . 23Diameters up to 2-5/16” and 60.5mm
PageRiten Power Collet Chucks Riten Collets
Drawtube Adapter Specifications . . . . . . . . . . . . . .24
Accuracy Chart: 5C, 16C and R8 . . . . . . . . . . . . . .25
Accuracy Chart: Multibore & B Type . . . . . . . . . . . 26
4
www.riten.com
®
5C & 16C Set Length Power ChucksSetrite® Adjustment for A Type andStraight Recess DIN 6353
B
A
K
CE
PIT
CH
CIR
CLE
H
.472" min
I
D H
6
G C
LAS
S 6
H
.276
F MOUNTING HOLES (6)
M NS
PIN
DLE
CLA
SS
L
P
J
H
G C
LAS
S 6
H
St. Recess Model No.
w/Mount Model No.
Mount
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
F
G Thread
H
I
J
K
L
M
N
P
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Weight/Wt.w/Mount
5C390 5C390
5C250 5C260
A2-5 A2-6
1.125 / 27 1.125 / 27
.875 /22 .875 / 22 .
.70 / 17.8 .70 / 17.8
3.34 / 85 3.34 / 85
4.33 / 111 4.33 / 111
4.72 / 120 4.72 / 120
3.15 / 80 3.15 / 80
3.93 / 100 3.93 / 100
M8 M8
M68 x 1.5 M68 x 1.5
.51 / 13 .51 / 13
1.10 / 28-.95 / 25 1.10 / 28-.95 / 25
2.28 / 58-2.15 / 55 2.28 / 58-2.15 / 55
.94 / 24 .94 / 24
5.55 / 141 5.55 / 141
5.31 / 135 6.49 / 165
2.44 / 62 2.44 / 62
1.18 / 30 1.18 / 30
6000 6000
4,046 4,046
12,500 12,500
9.3/15 lbs. 9.3/17.8 lbs.
16C685 16C685 16C685
16C250 16C260 16C140
A2-5 A2-6 140x6
1.625 / 42 1.625 / 42 1.625 / 42
1.375 / 35 1.375 / 35 1.375 / 35
1.14 / 29 1.14 / 29 1.14 / 29
4.31 / 110 4.31 / 110 4.31 / 110
5.43 / 138 5.43 / 138 5.43 / 138
6.10 / 155 6.10 / 155 6.10 / 155
3.70 / 94 3.70 / 94 3.70 / 94
5.11 / 130 5.11 / 130 5.11 / 130
M10 M10 M10
M88 x 1.5 M88 x 1.5 M88 x 1.5
.51 / 13 .51 / 13 .51 / 13
1.10 / 28-.94 / 25 1.10 / 28-.94 / 25 1.10 / 28-.94 / 25
2.28 / 58-2.16 / 55 2.28 / 58-2.16 / 55 2.0 / 51-1.85 / 47
.86 / 22 .86 / 22 .86 / 22
6.34 / 161 6.61 / 168 6.34 / 161
6.10 / 155 6.49 / 165 6.10 / 155
3.03 / 77 3.03 / 77 3.03 / 77
.91 / 23 1.18 / 30 .91 / 23
6000 6000 6000
5,392 5,392 5,392
17,000 17,000 17,000
17.6/23.5 lbs. 17.6/26 lbs. 17.6/X?5 lbs.
For 5C Type Collets For 16C- Type Collets
■ Setrite® four-screw adjustment feature allows accuracy adjustment to virtual zero, eliminating any error in the collet
■ Main spindle and sub-spindle CNC chuck applications■ Accuracy guaranteed to .0002” TIR from rear
mounting register and working collet taper■ Repeatability is .0002” TIR■ Hardened and ground main body and cone■ Speeds up to 6000 rpm
Dimensions
shown in in / mm
Straight Recessed
5C Collet
16C Collet
With A5 or A6 Mount
See pages 13-16 for collet specifications.
5
Call 1-800-338-0027
See pages 13-16 for collet specifications.
®
5C & 16C Set Length Power ChucksFor A Type and DIN 6353Straight Recess Mounts
C
B
J
G C
LAS
S 6
H
H
A
K
C D H
6
E P
ITC
H C
IRC
LE
G C
LAS
S 6
H
A
B
.236"
K
F MOUNTING HOLES (6)
H
J
Chuck Model No.
Mount
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
F
G thread
J
K
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
5C251 5C261 5C141
A2-5 A2-6 140x6
1.125 / 27 1.125 / 27 1.125 / 27
.875 / 22 .875 / 22 .875 / 22
.750 / 19 .750 / 19 .750 / 19
3.34 / 85 3.34 / 85 3.34 / 85
4.60 / 117 4.60 / 117 4.60 / 117
5.31 / 135 6.49 / 165 6.30 / 160
– – 5.51 / 140
– – 4.126 / 104.8
– – M10
M68 x 1.5 M68 x 1.5 M68 x 1.5
1.33 / 34-1.26 / 31 1.33 / 34-1.26 / 31 1.33 / 34-1.26 / 31
.98 / 25 1.18 / 30 1.18 / 30
6000 6000 6000
4,046 4,046 4,046
12,500 12,500 12,500
10.6 lbs 13 lbs 12.3 lbs
Dimensions shown in in/mm
16C261 16C280 16C170
A2-6 A2-8 170 x 6
1.625 / 42 1.625 / 42 1.625 / 42
1.375 / 35 1.375 / 35 1.375 / 35
1.00 / 25.4 1.00 / 25.4 1.00 / 25.4
4.33 / 110 4.33 / 110 4.33 / 110
5.67 / 144 6.34 / 161 5.67 / 144
6.49 / 165 8.66 / 220 7.87 / 200
– – 6.69 / 170
– – 5.25 / 133.4
– – M12
M88 x 1.5 M88 x 1.5 M88 x 1.5
1.33 / 34-1.18 / 30 1.33 / 34-1.18 / 30 1.33 / 34-1.18 / 30
1.18 / 30 1.18 / 30 1.18 / 30
6000 4500 4500
5,392 5,392 5,392
17,000 17,000 17,000
20.5 lbs 26 lbs 23.6 lbs
For 5C Type Collets For 16C Type Collets
■ Short overall length ideal for main spindle and sub-spindle applications
■ In second operations work, shoulder components canbe stopped against the face of the collet.
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR
■ Hardened and ground main body and cone
■ Speeds up to 6000 rpm
A2 Mount
5C Collet
16C Collet
DIN 6353 Mounts
6
www.riten.com
®5C & 16C Collet ChucksPullback design for A Type and Straight Recess DIN 6353
L
J B E
C
A
D
Chuck Model No.
Mount
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
J
L
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
5C245 5C255 5C256 5C265 5C266 5C285 5C145
A2-4 A2-5 A2-5 A2-6 A2-6 A2-8 140x6
1.125 / 27 1.125 / 27 1.125 / 27 1.125 / 27 1.125 / 27 1.125 / 27 1.125 / 27
.875 / 22 .875 / 22 .875 / 22 .875 / 22 .875 / 22 .875 / 22 .875 / 22
.750 / 19 .750 / 19 .750 / 19 .750 / 19 .750 / 19 .750 / 19 .750 / 19
2.41 / 61 3.19 /81 3.19 / 81 4.17 / 106 4.17 / 106 5.51 / 140 3.26 / 83
4.25 / 108 5.31 / 135 5.31 / 135 6.69 / 170 6.69 / 170 8.66 / 220 6.30 / 160
3.54 / 90 5.0 / 127 3.50 / 89 5.0 / 127 6.0 / 153 6.0 / 153 5.0 / 127
.87 / 22 .98 / 25 .98 / 25 .98 / 25 .98 / 25 1.18 / 30 .98 / 25
2.5 / 64 3.25 / 82.6 3.2 5/ 82.6 4.19 / 106.4 4.19 / 106.4 5.5 / 139.7 5.51 / 140
43.8 / 1.7 2.4 / 60.8 2.4 / 60.8 3.26 / 82.8 3.26 / 82.8 4.3 / 109.8 2.36 / 60
2.16 / 55 3.54 / 90 2.36 / 60 3.15 / 80 4.72 / 120 4.72 / 120 3.07 / 78
6000 6000 6000 6000 6000 4500 6000
4,496 4,496 4,496 4,496 4,496 4,496 4,496
15,700 15,700 15,700 15,700 15,700 15,700 15,700
10 lbs 14 lbs 12 lbs 18 lbs 21 lbs 29 lbs 14 lbs
Dimensions shown in in/mm
16C255 16C265 16C285
A2-5 A2-6 A2-8
1.625 / 42 1.625 / 42 1.625 / 42
1.375 / 35 1.375 / 35 1.375 / 35
1.00 / 25.4 1.00 / 25.4 1.00 / 25.4
3.24 / 82.5 4.21 / 107 5.51 / 140
5.31 / 135 6.69 / 170 8.66 / 220
6.00 / 152.5 6.00 / 152.5 6.00 / 152.5
.98 / 25 .98 / 25 1.18 / 30
3.25 / 82.6 4.19 / 106.4 5.5 / 139.7
2.39 / 60.8 3.26 / 82.8 4.32 / 109.8
3.94 / 100 4.13 / 105 4.13 / 105
6000 6000 4500
5,394 5,394 5,394
19,500 19,500 19,500
15 lbs 20 lbs 33 lbs
For 5C Type Collets For 16C Type Collets
■ Used on CNC turning machines with drawtube actuation
■ Main spindle and sub-spindle CNC chuck applications
■ Suitable for bar work and second operation machining
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR
■ Hardened and ground main body and cone
■ Speeds up to 6000 rpm
DrawtubeAdapter Collet Chuck
5C Collet 16C Collet
See pages 13-16 for collet specifications.
7
Call 1-800-338-0027
®Multibore Standard Collet ChucksSet length operation for DIN standardMultibore and B type spring collets and A type mounts
A
CD
G
H
F
L
JEB
Chuck Model No.
Mount
DIN Multibore Collet
Capacity, Round
Capacity, Hex
Capacity, Square
Spring Collet
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
F
G
H
J
L
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
J495 J496 J475 J498 J834 A2-5 A2-6 A2-6 A2-8 A2-8 M673 M673 M677 M677 J660
1.65 / 42 1.65 / 42 2.36 / 60 2.36 / 60 3.15 / 80 1.41 / 36 1.41 / 36 2.04 / 52 2.04 / 52 2.71 / 69 1.14 / 29 1.14 / 29 1.65 / 42 1.65 / 42 2.20 / 56
B42 B42 B60 B60 B801.65 / 42 1.65 / 42 2.36 / 60 2.36 / 60 3.15 / 80 1.50 / 38 1.50 / 38 2.05 / 52 2.05 / 52 2.71 / 691.18 / 30 1.18 / 30 1.65 / 42 1.65 / 42 2.20 / 56
4.57 / 116 4.57 / 116 5.59 / 142 5.59 / 142 8.66 / 2205.31 / 135 6.69 / 170 6.69 / 170 6.69 / 170 8.66 / 220
4.67 / 118.5 4.67 / 118.5 5.77 / 146.5 5.77 / 146.5 7.81 / 198.5.98 / 25 .98 / 25 1.18 / 30 1.18 / 30 1.18 / 30
3.25 / 82.58 4.19 / 106.4 4.19 / 106.4 5.5 / 139.7 5.5 / 139.7M58 x 1.5 M58 x 1.5 M76 x 1.5 M76 x 1.5 M100 x 2.0
.75 / 19-1.1 / 28 .75 / 19-1.14 / 29 .94 / 24-1.39 / 34 .94 / 24-1.39 / 34 1.81 / 46-2.28 / 58.59 / 15 .59 / 15 .59 / 15 .59 / 15 2.28 / 58
2.56 / 65 2.56 / 65 3.27 / 83 3.27 / 83 4.17 / 1063.15 / 80 3.15 / 80 3.15 / 80 3.15 / 80 4.33 / 110
6000 6000 6000 4500 40005,390 5,390 8,530 8,530 9,885
13,200 13,200 22,100 22,100 25,70028 lbs 28 lbs 39 lbs 39 lbs 54 lbs
Dimensions shown in in/mm
■ Uses DIN type Multibore collets for a powerful parallel gripover a wide diameter range. When gripping short compo-
nents,or where marking of a finished diameter is to be avoided, use B type spring collets or a fixed bore size collet.
■ Large capacity: up to 2.625” round
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR■ Hardened and ground main body and cone■ Speeds up to 6000 rpm■ Also available in DIN 55026 mountings
DrawtubeAdapter
B typeSpring ColletMultibore
Collet
See pages 19-23 for collet specifications.
8
www.riten.com
®Multibore Short Collet ChucksSet length operation for Multiborestandard collets and A type mounts
B
J C D
E
F
L
A
Chuck Model No.
Mount
Std. Multibore Collet
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D*
E
F
J
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
F325 F757 F327 F941
A2-5 A2-5 A2-6 A2-6
W-850 V-120 V-120 T-285
1.65 / 42 2.12 / 54 2.12 / 54 2.59 / 66
1.49 / 38 2.00 / 51 2.00 / 51 2.24 / 57
1.22 / 31 1.61 / 41 1.61 / 41 1.78 / 44
4.57 / 116 5.59 / 142 5.59 / 142 6.69 / 170
3.86 / 98 4.49 / 113 5.08 / 129 5.78 / 131
M68 x 1.5 M70 x 1.5 M70 x 2.0 M70 x 2.0
2.36 / 60 2.09 / 52 2.44 / 62 2.95 / 75
1.31 /34 - 1.69 /43 1.22 / 31 - 1.61 / 41 1.81 / 48 - 2.28 / 58 1.81 / 48 - 2.28 / 58
.71 / 18 .59 / 15 .79 / 20 1.18 / 30
2.56 / 65 2.16 / 55 3.27 / 83 3.78 / 96
6000 6000 6000 5000
5,390 8,535 8,535 8,535
13,200 22,200 22,200 22,200
22 lbs 34 lbs 34 lbs 48 lbs
Dimensions shown in in/mm
■ Ideal for bar work with minimum working envelope (not suitable for gripping short components for secondaryoperation).
■ Large capacity: up to 2.59” round
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR■ Hardened and ground main body and cone■ Speeds up to 6000 rpm■ Also available in DIN 55026 mountings
* D represents the maximum drawtube thread diameter in conjunction with a drawtube adapter.
DrawtubeAdapter
MultiboreCollet
See pages 17 and 18 for collet specifications.
DC A
B
9
Call 1-800-338-0027
®Quick Change Collet Chucks, Type ASet length operation for DIN standardMultibore and B type spring colletsand A type mounts
Chuck Model No.
Mount
DIN Multibore Collet
Spring Collet1
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
Chuck Seal Part No.2
Chuck Cap Part No.3
Ejector Part No.
Backstop Part No.
D233 D234 D475 D477 A2-5 A2-6 A2-6 A2-8 M673 M673 M677 M677B42 B42 B60 B60
1.65 / 42 1.65 / 42 2.36 / 60 2.36 / 60 1.50 / 38 1.50 / 38 2.05 / 52 2.05 / 52 1.18 / 30 1.18 / 30 1.65 / 42 1.65 / 42
4.49 / 114 4.49 / 114 5.75 / 146 5.75 / 1465.79 / 147 5.79 / 147 7.52 / 191 7.52 / 1912.36 / 60 2.36 / 60 2.76 / 70 2.76 / 701.22 / 31 1.22 / 31 1.89 / 48 1.89 / 48.35 / 9 .35 / 9 .39 / 10 .39 / 106000 6000 6000 45005,392 5,392 8,536 8,536
13,199 13,199 22,200 22,20019 lbs 19.8 lbs 28.1 lbs 30.9 lbs D237 D237 D485 D485
C428GA C428GA C142GA C142GAD242 D242 D490 D490D241 D241 D678 D678
Dimensions shown in in/mm
■ Quick change bayonet cap design saves setup time
■ Uses DIN type Multibore collets for a powerful parallel gripover a wide diameter range. When gripping short compo-
nents,or where marking of a finished diameter is to be avoided, use B type spring collets or a fixed bore size collet.
■ Large capacity: up to 2.36” round
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR■ Hardened and ground main body and cone■ Speeds up to 6000 rpm■ Also available in DIN 55026 mountings
1 Backstop cannot be used with Spring Collets.2 Each collet size requires a polyurethane chip Chuck Seal3 Additional Quick Change Chuck Caps can be ordered for
pre-loading collets and further reducing downtime.
B typeSpring ColletMultibore
Collet
See pages 19-23 forcollet specifications.
10
www.riten.com
®
Quick Change Collet Chucks, DINSet length operation for DIN standardMultibore and B type spring colletsand straight recess DIN 6353 mounts
DC
B
A
Chuck Model No.
Mount
DIN Multibore Collet
Spring Collet1
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
E
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
Chuck Seal Part No.2
Chuck Cap Part No.3
Ejector Part No.
Backstop Part No.
D634 D636 140 x 60 170 x 6
M673 M677B42 B60
1.65 / 42 2.36 / 60 1.41 / 36 2.04 / 52 1.14 / 29 1.65 / 42
4.49 / 114 5.75 / 1465.79 / 147 7.52 / 1912.36 / 60 2.76 / 701.22 / 31 1.89 / 48.35 / 9 .39 / 106000 60005,392 5,392
13,199 13,19919 lbs 30.9 lbs D237 D485
C428GA C142GAD242 D490D241 D489
Dimensions shown in in/mm
1 Backstop cannot be used with Spring Collets.2 Each collet size requires a polyurethane chip Chuck Seal3 Additional Quick Change Chuck Caps can be ordered for
pre-loading collets and further reducing downtime.
■ Quick change bayonet cap design saves setup time
■ Uses DIN type Multibore collets for a powerful parallel gripover a wide diameter range. When gripping short compnents,or where marking of a finished diameter is to be avoided, use B type spring collets or a fixed bore size collet.
■ Large capacity: up to 2.36” round
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR■ Hardened and ground main body and cone■ Speeds up to 6000 rpm■ Call for availability of A type spindle mountings.
A C
BD
B type Spring ColletMultiboreCollet
See pages 19-23 forcollet specifications.
11
Call 1-800-338-0027
Chuck Model No.
Mount
Multibore Collet
Capacity, Round
Capacity, Hex
Capacity, Square
A
B
C
D
Max Forward Stroke Required
Maxmimum RPM
Drawbar Force (lb/ft)
Clamping Force (lb/ft)
Approx. Chuck Weight
Chuck Seal Part No.1
Chuck Cap Part No.2
D607 D608 D609 D610
A2-5 A2-6 A2-6 A2-8
M673 M673 M677 M677
1.65/42 1.65/42 2.36/60 2.36/60
1.41/36 1.41/36 2.04/52 2.04/52
1.14/29 1.14/29 1.65/42 1.65/42
4.49/114 4.49/114 5.75/146 5.75/146
4.33/110 4.33/110 5.35/136 5.35/136
2.36/60 2.36/60 2.76/70 2.76/70
1.22/31 1.22/31 1.89/48 1.89/48
.35 / 9 .35 / 9 .39 / 10 .39 / 10
6000 6000 6000 4500
5,392 5,392 8,536 8,536
13,199 13,199 22,200 22,200
15 lbs 15.4 lbs 22 lbs 30.9 lbs
D237 D237 D485 D485
C428GA C428GA C142GA C142GA
For DIN Multibore Collets
®Quick Change Collet Chucks, ShortSet length operation for standard or DINMultibore collets and A type mounts
DA
B
C
C19 D603 D428 D604 D605 D606 D548
A2-5 A2-5 A2-6 A2-6 A2-8 A2-8 A2-8
T980 W850 W850 V120 V120 T285 N175
1.26 / 28 1.65 / 42 1.65 / 42 2.12 / 54 2.12 / 54 2.59 / 66 3.15 / 80
1.00 / 25 1.41 / 36 1.41 / 36 2.00 / 51 2.00 / 51 2.24 / 57 2.71 / 69
.75 / 19 1.22 / 31 1.22 / 31 1.61 / 41 1.61 / 41 1.78 / 44 2.20 / 56
3.14 / 95 4.49 / 114 4.49 / 114 5.75 / 146 5.75 / 146 6.54 / 166 8.07 / 205
4.41 / 112 4.33 / 110 4.33 / 110 5.51 / 140 5.51 / 140 6.10 / 155 6.69 / 170
1.57 / 40 2.36 / 60 2.36 / 60 2.76 / 70 2.76 / 70 3.46 / 88 3.46 / 88
1.22 / 31 1.22 / 31 1.22 / 31 1.89 / 48 1.89 / 48 1.89 / 48 2.28 / 58
.35 / 9 .35 / 9 .35 / 9 .39 / 10 .39 / 10 .39 / 10 .47 / 12
6000 6000 6000 6000 4500 4500 4000
4,037 5,392 5,392 8,536 8,536 8,536 9,885
9,878 13,199 13,199 22,200 22,200 22,200 25,699
11 lbs 15 lbs 15.4 lbs 22 lbs 30.9 lbs 39 lbs 55.1 lbs
D819 D237 D237 D485 D485 D619 D548
C555GA C68GA C68GA C983GA C983GA C556GA C492GA
Dimensions shown
in in/mm
■ Short body design ideal for bar work with limited workingenvelope
■ Quick change bayonet cap design saves setup time
■ Models available for both standard and DIN type Multiborecollets
■ Large capacity: up to 3.07” round
■ Accuracy guaranteed to .0002” TIR from rear mounting register and working collet taper
■ Repeatability is .0002” TIR
■ Hardened and ground main body and cone
■ Speeds up to 6000 rpm
■ Call for availability of A type spindle mountings.
1 Each collet size requires a polyurethane chip Chuck Seak2 Additional Quick Change Chuck Caps can be ordered for pre-loading collets and further reducing downtime.
For Standard Multibore Collets
See pages 17-19 for collet specifications.
® R8 Collets (inch and Metric)Round only
C
D
A
B
1/16” R8-R-1/16 3/32” R8-R-3/321/8” R8-R-1/8
5/32” R8-R-5/323/16” R8-R-3/167/32” R8-R-7/32 1/4” R8-R-1/4
9/32” R8-R-9/32 5/16” R8-R-5/16
11/32” R8-R-11/323/8” R8-R-3/8
13/32” R8-R-13/327/16” R8-R-7/16
15/32” R8-R-15/321/2” R8-R-1/2
17/32” R8-R-17/32 9/16” R8-R-9/16
19/32” R8-R-19/325/8” R8-R-5/8
21/32” R8-R-21/3211/16” R8-R-11/1623/32” R8-R-23/32
3/4” R8-R-3/425/32” R8-R-25/3213/16” R8-R-13/1627/32” R8-R-27/32
Size Part Number (inch)
A B C D
.95” 4.05” 1.24” 8°25’
2mm R8-R-2 3mm R8-R-34mm R8-R-4 5mm R8-R-56mm R8-R-6 7mm R8-R-78mm R8-R-89mm R8-R-9
10mm R8-R-1011mm R8-R-1112mm R8-R-1213mm R8-R-1314mm R8-R-1415mm R8-R-1516mm R8-R-1617mm R8-R-17 18mm R8-R-1819mm R8-R-1920mm R8-R-20
Size Part Number (Metric)
Set No. of Collets Model No.
R8 Round Collet Set (Metric)
2mm – 20mm x 1mm 19 R8-SET-1
Dimensions (inches)
Set No. of Collets Model No.
R8 Round Collet Sets (inch)
1/8” – 3/4” x 32nds 21 R8-SET-5
1/8” – 3/4” x 16ths 11 R8-SET-6
1/8” – 3/4” x 8ths 6 R8-SET-7
12
www.riten.com
13
Call 1-800-338-0027
® 5C Collets (inch)Round, Hex and Square
1/64” 5C-R-1/64 1/32” 5C-R-1/32 3/64” 5C-R-3/64 1/16” 5C-R-1/16 5/64” 5C-R-5/64 3/32” 5C-R-3/327/64” 5C-R-7/641/8” 5C-R-1/8 5C-H-1/8 5C-S-1/8
9/64” 5C-R-9/645/32” 5C-R-5/32
11/64” 5C-R-11/643/16” 5C-R-3/16 5C-H-3/16 5C-S-3/16
13/64” 5C-R-13/647/32” 5C-R-7/32
15/64” 5C-R-15/641/4” 5C-R-1/4 5C-H-1/4 5C-S-1/4
17/64” 5C-R-17/649/32” 5C-R-9/32
19/64” 5C-R-19/645/16” 5C-R-5/16 5C-H-5/16 5C-S-5/16
21/64” 5C-R-21/6411/32” 5C-R-11/3223/64” 5C-R-23/64
3/8” 5C-R-3/8 5C-H-3/8 5C-S-3/825/64” 5C-R-25/6413/32” 5C-R-13/3227/64” 5C-R-27/647/16” 5C-R-7/16 5C-H-7/16 5C-S-7/16
29/64” 5C-R-29/6415/32” 5C-R-15/3231/64” 5C-R-31/64
1/2” 5C-R-1/2 5C-H-1/2 5C-S-1/233/64” 5C-R-33/6417/32” 5C-R-17/32 35/64” 5C-R-35/649/16” 5C-R-9/16 5C-H-9/16 5C-S-9/16
37/64” 5C-R-37/6419/32” 5C-R-19/3239/64” 5C-R-39/64
5/8” 5C-R-5/8 5C-H-5/8 5C-S-5/841/64” 5C-R-41/6421/32” 5C-R-21/3243/64” 5C-R-43/6411/16” 5C-R-11/16 5C-H-11/16 5C-S-11/16
Size Round Hex Square
A B C D
1.25” 3.28” 1.47” 10°
45/64” 5C-R-45/64 23/32” 5C-R-23/3247/64” 5C-R-47/64 3/4” 5C-R-3/4 5C-H-3/4 5C-S-3/4
49/64” 5C-R-49/64 25/32” 5C-R-29/3251/64” 5C-R-51/6413/16” 5C-R-13/16 5C-H-13/16 53/64” 5C-R-53/6427/32” 5C-R-27/3255/64” 5C-R-55/64
7/8” 5C-R-7/857/64” 5C-R-57/6429/32” 5C-R-29/3259/64” 5C-R-59/6415/16” 5C-R-15/16 61/64” 5C-R-61/6431/32” 5C-R-31/32 63/64” 5C-R-63/64
1” 5C-R-11-1/64” 5C-R-1-1/641-1/32” 5C-R-1-1/321-3/64” 5C-R-1-3/641-1/16” 5C-R-1-1/161-5/64” 5C-R-1-5/641-3/32” 5C-R-1-3/321-7/64” 5C-R-1-7/641-1/8” 5C-R-1-1/8
Size Round Hex Square
Set No. of Collets Model No.
5C Round Collet Sets (inch)
1/16” – 1-1/16” x 64ths 65 5C-SET-41/16” – 1-1/16” x 32nds 33 5C-SET-51/16” – 1-1/16” x 16ths 17 5C-SET-61/8” – 1 x 64ths 8 5C-SET-7
Dimensions (inches)
Emergency Collet: 5C-EC
A
B
C
D
14
www.riten.com
® 5C Collets (Metric)Round only
0.5mm 5C-R-0.5
1.0mm 5C-R-1.0
1.5mm 5C-R-1.5
2.0mm 5C-R-2.0
2.5mm 5C-R-2.5
3.0mm 5C-R-3.0
3.5mm 5C-R-3.5
4.0mm 5C-R-4.0
4.5mm 5C-R-4.5
5.0mm 5C-R-5.0
5.5mm 5C-R-5.5
6.0mm 5C-R-6.0
6.5mm 5C-R-6.5
7.0mm 5C-R-7.0
7.5mm 5C-R-7.5
8.0mm 5C-R-8.0
8.5mm 5C-R-8.5
9.0mm 5C-R-9.0
9.5mm 5C-R-9.5
10.0mm 5C-R-10.0
10.5mm 5C-R-10.5
11.0mm 5C-R-11.0
11.5mm 5C-R-11.5
12.0mm 5C-R-12.0
12.5mm 5C-R-12.5
13.0mm 5C-R-13.0
13.5mm 5C-R-13.5
14.0mm 5C-R-14.0
14.5mm 5C-R-14.5
15.0mm 5C-R-15.0
15.5mm 5C-R-15.5
16.0mm 5C-R-16.0
16.5mm 5C-R-16.5
17.0mm 5C-R-17.0
17.5mm 5C-R-17.5
Size Part Number
A B C D
31.75 85.4 37.3 10°
18.0mm 5C-R-18.0
18.5mm 5C-R-18.5
19.0mm 5C-R-19.0
19.5mm 5C-R-19.5
20.0mm 5C-R-20.0
20.5mm 5C-R-20.5
21.0mm 5C-R-21.0
21.5mm 5C-R-21.5
22.0mm 5C-R-22.0
23.0mm 5C-R-23.0
23.5mm 5C-R-23.5
24.0mm 5C-R-24.0
24.5mm 5C-R-24.5
25.0mm 5C-R-25.0
25.5mm 5C-R-25.5
26.0mm 5C-R-26.0
26.5mm 5C-R-26.5
27.0mm 5C-R-27.0
Set No. of Collets Model No.
5C Round Collet Sets (Metric)
3mm-27mm x 0.5mm 49 5C-SET-1
3mm-27mm x 1mm 25 5C-SET-2
Dimensions (mm)
Size Part Number
Emergency Collet: 5C-EC
A
B
C
D
15
Call 1-800-338-0027
® 16C Collets (inch)Round, Hex and Square
A
B
C
D
1/16” 16C-R-1/16 1/8” 16C-R-1/8
3/16” 16C-R-3/161/4” 16C-R-1/4 16C-H-1/4 16C-S-1/4
5/16” 16C-R-5/16 16C-H-5/16 16C-S-5/163/8” 16C-R-3/8 16C-H-3/8 16C-S-3/8
7/16” 16C-R-7/16 16C-H-7/16 16C-S-7/161/2” 16C-R-1/2 16C-H-1/2 16C-S-1/2
9/16” 16C-R-9/16 16C-H-9/16 16C-S-9/165/8” 16C-R-5/8 16C-H-5/8 16C-S-5/8
11/16” 16C-R-11/16 16C-H-11/16 16C-S-11/163/4” 16C-R-3/4 16C-H-3/4 16C-S-3/4
13/16” 16C-R-13/16 16C-H-13/16 16C-S-13/167/8” 16C-R-7/8 16C-H-7/8 16C-S-7/8
15/16” 16C-R-15/16 16C-H-15/16 16C-S-15/161” 16C-R-1 16C-H-1 16C-S-1
1-1/16” 16C-R-1-1/16 16C-H-1-1/161-1/8” 16C-R-1-1/8 16C-H-1-1/8
1-3/16” 16C-R-1-3/16 16C-H-1-3/161-1/4” 16C-R-1-1/4 16C-H-1-1/4
1-5/16” 16C-R-1-5/16 16C-H-1-5/161-3/8” 16C-R-1-3/8 16C-H-1-3/8
1-7/16” 16C-R-1-7/161-1/2” 16C-R-1-1/2
1-9/16” 16C-R-1-9/161-5/8” 16C-R-1-5/8
Size Round Hex Square
A B C D
1.89” 4.35” 2.26” 10°
Dimensions (inches)
Emergency Collet: 16C-EC
® 16C Collets (Metric)Round, Hex and Square
A
B
C
D
1.0mm 16C-R-1.01.5mm 16C-R-1.5 2.0mm 16C-R-2.0 2.5mm 16C-R-2.5 3.0mm 16C-R-3.03.5mm 16C-R-3.5 4.0mm 16C-R-4.04.5mm 16C-R-4.55.0mm 16C-R-5.0 5.5mm 16C-R-5.56.0mm 16C-R-6.0 16C-H-6.0 16C-S-6.06.5mm 16C-R-6.5 16C-H-6.5 16C-S-6.57.0mm 16C-R-7.0 16C-H-7.0 16C-S-7.07.5mm 16C-R-7.5 16C-H-7.5 16C-S-7.58.0mm 16C-R-8.0 16C-H-8.0 16C-S-8.08.5mm 16C-R-8.5 16C-H-8.5 16C-S-8.59.0mm 16C-R-9.0 16C-H-9.0 16C-S-9.0 9.5mm 16C-R-9.5 16C-H-9.5 16C-S-9.5
10.0mm 16C-R-10.0 16C-H-10.0 16C-S-10.010.5mm 16C-R-10.5 16C-H-10.5 16C-S-10.511.0mm 16C-R-11.0 16C-H-11.0 16C-S-11.011.5mm 16C-R-11.5 16C-H-11.5 16C-S-11.512.0mm 16C-R-12.0 16C-H-12.0 16C-S-12.012.5mm 16C-R-12.5 16C-H-12.5 16C-S-12.513.0mm 16C-R-13.0 16C-H-13.0 16C-S-13.013.5mm 16C-R-13.5 16C-H-13.5 16C-S-13.514.0mm 16C-R-14.0 16C-H-14.0 16C-S-14.014.5mm 16C-R-14.5 16C-H-14.5 16C-S-14.515.0mm 16C-R-15.0 16C-H-15.0 16C-S-15.015.5mm 16C-R-15.5 16C-H-15.5 16C-S-15.516.0mm 16C-R-16.0 16C-H-16.0 16C-S-16.016.5mm 16C-R-16.5 16C-H-16.5 16C-S-16.517.0mm 16C-R-17.0 16C-H-17.0 16C-S-17.0 17.5mm 16C-R-17.5 16C-H-17.5 16C-S-17.518.0mm 16C-R-18.0 16C-H-18.0 16C-S-18.018.5mm 16C-R-18.5 16C-H-18.5 16C-S-18.519.0mm 16C-R-19.0 16C-H-19.0 16C-S-19.019.5mm 16C-R-19.5 16C-H-19.5 16C-S-19.520.0mm 16C-R-20.0 16C-H-20.0 16C-S-20.020.5mm 16C-R-20.5 16C-H-20.5 16C-S-20.521.0mm 16C-R-21.0 16C-H-21.0 16C-S-21.021.5mm 16C-R-21.5 16C-H-21.5 16C-S-21.5
Size Round Hex Square
A B C D
48 110.5 57.5 10°
22.0mm 16C-R-22.0 16C-H-22.0 16C-S-22.022.5mm 16C-R-22.5 16C-H-22.5 16C-S-22.523.0mm 16C-R-23.0 16C-H-23.0 16C-S-23.0 23.5mm 16C-R-23.5 16C-H-23.5 16C-S-25.0 24.0mm 16C-R-24.0 16C-H-24.0 16C-S-24.024.5mm 16C-R-24.5 16C-H-24.5 16C-S-24.525.0mm 16C-R-25.0 16C-H-25.0 16C-S-25.0 25.5mm 16C-R-25.5 16C-H-25.526.0mm 16C-R-26.0 16C-H-26.026.5mm 16C-R-26.5 16C-H-26.527.0mm 16C-R-27.0 16C-H-27.027.5mm 16C-R-27.5 16C-H-27.528.0mm 16C-R-28.0 16C-H-28.028.5mm 16C-R-28.5 16C-H-28.529.0mm 16C-R-29.0 16C-H-29.029.5mm 16C-R-29.5 16C-H-29.530.0mm 16C-R-30.0 16C-H-30.030.5mm 16C-R-30.5 16C-H-30.531.0mm 16C-R-31.0 16C-H-31.031.5mm 16C-R-31.5 16C-H-31.532.0mm 16C-R-32.0 16C-H-32.032.5mm 16C-R-32.5 16C-H-32.533.0mm 16C-R-33.0 16C-H-33.033.5mm 16C-R-33.5 16C-H-33.534.0mm 16C-R-34.0 16C-H-34.034.5mm 16C-R-34.5 16C-H-34.535.0mm 16C-R-35.0 16C-H-35.035.5mm 16C-R-35.536.0mm 16C-R-36.036.5mm 16C-R-36.537.0mm 16C-R-37.037.5mm 16C-R-37.538.0mm 16C-R-38.038.5mm 16C-R-38.539.0mm 16C-R-39.039.5mm 16C-R-39.540.0mm 16C-R-40.040.5mm 16C-R-40.541.0mm 16C-R-41.041.5mm 16C-R-41.542.0mm 16C-R-42.042.5mm 16C-R-42.5
Dimensions (mm)
Size Round Hex Square
16
www.riten.comEmergency Collet: 16C-EC
® Plain Bore Multibore Collets
CA
B
Part No. A B C
T980 1.66” 1.99” 14°W850 2.04” 2.76” 15°V120 2.47” 3.46” 15°T285 2.88” 3.91” 15°N175 3.15” 4.72” 15°
Dimensions (inches)
1/16 - 3/16 1.58 - 4.761/8 - 1/4 3.17 - 6.351/4 - 3/8 6.35 - 9.523/8 - 1/2 9.52 - 12.701/2 - 5/8 12.70 - 15.875/8 - 3/4 15.87 - 19.053/4 - 7/8 19.05 - 22.227/8 - 1 22.22 - 25.401 - 1-1/8 25.40 - 28.57
1-1/8 - 1-1/4 28.57 - 31.751-1/4 - 1-3/8 31.75 - 34.921-3/8 - 1-1/2 34.92 - 38.101-1/2 - 1-5/8 38.10 - 41.27 1-1/2 - 1-5/8 38.10 - 41.27
Grip Range Inch mm
T980-R-B1 T980-X-B68 T980-S-B86T980-R-B2 T980-X-B69 T980-S-B87T980-R-B3 T980-X-B70 T980-S-B88T980-R-B4 T980-X-B71 T980-S-B89T980-R-B5 T980-X-B72 T980-S-B90T980-R-B6 T980-X-B73 T980-S-B91T980-R-B7 T980-X-B74T980-R-B8 T980-X-B75T980-R-B9
T980 Round Hex Square
W850-R-C1 W850-X-C68 W850-S-C86W850-R-C2 W850-X-C69 W850-S-C87W850-R-C3 W850-X-C70 W850-S-C88W850-R-C4 W850-X-C71 W850-S-C89W850-R-C5 W850-X-C72 W850-S-C90W850-R-C6 W850-X-C73 W850-S-C91W850-R-C7 W850-X-C73 W850-S-C92W850-R-C8 W850-X-C74 W850-S-C93W850-R-C9 W850-X-C75 W850-S-C94W850-R-C10 W850-X-C76 W850-S-C95W850-R-C11 W850-X-C77W850-R-C12 W850-X-C78W850-R-C13 W850-X-C79W850-R-C14*
W850 Round Hex Square
V120-R-D1 V120-R-D2 V120-X-D69 V120-S-D87V120-R-D3 V120-X-D70 V120-S-D88V120-R-D4 V120-X-D71 V120-S-D89V120-R-D5 V120-X-D72 V120-S-D90V120-R-D6 V120-X-D73 V120-S-D91V120-R-D7 V120-X-D74 V120-S-D92V120-R-D8 V120-X-D75 V120-S-D93V120-R-D9 V120-X-D76 V120-S-D94V120-R-D10 V120-X-D77 V120-S-D95V120-R-D11 V120-X-D78 V120-S-D96V120-R-D12 V120-X-D79 V120-S-D97V120-R-D13 V120-X-D80 V120-S-D98V120-R-D14 V120-X-D81V120-R-D15 V120-X-D82V120-R-D16 V120-X-D83V120-R-D17
V120 Round Hex Square
1/16 - 3/16 1.58 - 4.761/8 - 1/4 3.17 - 6.351/4 - 3/8 6.35 - 9.523/8 - 1/2 9.52 - 12.701/2 - 5/8 12.70 - 15.875/8 - 3/4 15.87 - 19.053/4 - 7/8 19.05 - 22.227/8 - 1 22.22 - 25.401 - 1-1/8 25.40 - 28.57
1-1/8 - 1-1/4 28.57 - 31.751-1/4 - 1-3/8 31.75 - 34.921-3/8 - 1-1/2 34.92 - 38.101-1/2 - 1-5/8 38.10 - 41.27 1-5/8 - 1-3/4 41.27 - 44.451-3/4 - 1-7/8 44.45 - 47.62
1-7/8 - 2 47.62 - 50.802 - 2-1/8 50.80 - 53.97
2-1/8 - 2-1/4 53.97 - 57.152-1/4 - 2-3/8 57.15 - 60.322-3/8 - 2-1/2 60.32 - 63.502-1/2 - 2-5/8 63.50 - 66.672-5/8 - 2-3/4 66.67 - 69.852-3/4 - 2-7/8 69.85 - 73.02
2-7/8 - 3 73.02 - 76.203 - 3-1/8 76.20 - 79.37
Grip Range Inch mm
N175-R-F5 N175-X-F72 N175-S-F100N175-R-F6 N175-X-F73 N175-S-F101N175-R-F7 N175-X-F74 N175-S-F102N175-R-F8 N175-X-F75 N175-S-F103N175-R-F9 N175-X-F76 N175-S-F104N175-R-F10 N175-X-F77 N175-S-F105N175-R-F11 N175-X-F78 N175-S-F106N175-R-F12 N175-X-F79 N175-S-F107N175-R-F13 N175-X-F80 N175-S-F108N175-R-F14 N175-X-F81 N175-S-F109N175-R-F15 N175-X-F82 N175-S-F110N175-R-F16 N175-X-F83 N175-S-F111N175-R-F17 N175-X-F84 N175-S-F112N175-R-F18 N175-X-F85N175-R-F19 N175-X-F86N175-R-F20 N175-X-F87N175-R-F21 N175-X-F88N175-R-F22N175-R-F23N175-R-F24N175-R-F25
Round N175 & Smooth Bore Hex Square
T285-R-E2 T285-X-E69 T285-S-E87T285-R-E3 T285-X-E70 T285-S-E88T285-R-E4 T285-X-E71 T285-S-E89T285-R-E5 T285-X-E72 T285-S-E90T285-R-E6 T285-X-E73 T285-S-E91T285-R-E7 T285-X-E74 T285-S-E92T285-R-E8 T285-X-E75 T285-S-E93T285-R-E9 T285-X-E76 T285-S-E94T285-R-E10 T285-X-E77 T285-S-E95T285-R-E11 T285-X-E78 T285-S-E96T285-R-E12 T285-X-E79 T285-S-E97T285-R-E13 T285-X-E80 T285-S-E98T285-R-E14 T285-X-E81 T285-S-E99T285-R-E15 T285-X-E82T285-R-E16 T285-X-E83T285-R-E17 T285-X-E84T285-R-E18 T285-X-E85T285-R-E19T285-R-E20T285-R-E21
T285 Round Hex Square
* 39-42mm round only
17
Call 1-800-338-0027
® Heavy Duty Multibore Collets
CA
B
Part No. A B C
W850 2.04” 2.76” 15°V120 2.47” 3.46” 15°T285 2.88” 3.91” 15°N175 3.15” 4.72” 15°
Dimensions (inches)
.23 - .35 6 - 9
.35 - .47 9 - 12
.47 - .59 12 - 15
.59 - .70 15 - 18
.70 - .82 18 - 21
.82 - .94 21 - 24.94 - 1.06 24 - 27
1.06 - 1.18 27 - 301.18 - 1.30 30 - 331.30 - 1.41 33 - 361.41 - 1.53 36 - 391.53 - 1.65 39 - 421.65 - 1.77 42 - 45 1.77 - 1.89 45 - 481.89 - 2.00 48 - 512.00 - 2.12 51 - 54
Grip Range Inch mm
W850-RX-MM70 W850-S-MM98W850-RX-MM71 W850-S-MM99W850-RX-MM72 W850-S-MM100W850-RX-MM73 W850-S-MM101W850-RX-MM74 W850-S-MM102W850-RX-MM75 W850-S-MM103W850-RX-MM76 W850-S-MM104W850-RX-MM77 W850-S-MM105W850-RX-MM78W850-RX-MM79W850-R-MM13*W850-R-MM14*
W850 Heavy Duty Round/Hex Square
V120-RX-MN70 V120-S-MN98V120-RX-MN71 V120-S-MN99V120-RX-MN72 V120-S-MN100V120-RX-MN73 V120-S-MN101V120-RX-MN74 V120-S-MN102V120-RX-MN75 V120-S-MN103V120-RX-MN76 V120-S-MN104V120-RX-MN77 V120-S-MN105V120-RX-MN78 V120-S-MN106V120-RX-MN79 V120-S-MN107V120-RX-MN80 V120-S-MN108V120-RX-MN81V120-RX-MN82V120-RX-MN83V120-RX-MN84V120-R-MN18*
V120 Heavy Duty Round/Hex Square
.47 - .59 12 - 15
.59 - .70 15 - 18
.70 - .82 18 - 21
.82 - .94 21 - 24.94 - 1.06 21 - 24
1.06 - 1.18 27 - 301.18 - 1.30 30 - 331.30 - 1.41 33 - 361.41 - 1.53 36 - 391.53 - 1.65 39 - 421.65 - 1.77 42 - 45 1.77 - 1.89 45 - 481.89 - 2.00 48 - 512.00 - 2.12 51 - 542.12 - 2.24 54 - 572.24 - 2.36 57 - 602.36 - 2.46 60 - 632.46 - 2.59 63 - 662.59 - 2.71 66 - 692.71 - 2.83 69 - 722.83 - 2.95 72 - 752.95 - 3.07 75 - 78
Grip Range Inch mm
* Round only
T285-RX-MP72 T285-S-MP100T285-RX-MP73 T285-S-MP101T285-RX-MP74 T285-S-MP102T285-RX-MP75 T285-S-MP103T285-RX-MP76 T285-S-MP104T285-RX-MP77 T285-S-MP105T285-RX-MP78 T285-S-MP106T285-RX-MP79 T285-S-MP107T285-RX-MP80 T285-S-MP108T285-RX-MP81 T285-S-MP109T285-RX-MP82 T285-S-MP110T285-RX-MP83T285-RX-MP84T285-RX-MP85T285-RX-MP86T285-RX-MP87T285-R-MP21*
T285 Heavy Duty Round/Hex Square
N175-RX-MR72 N175-S-MR100N175-RX-MR73 N175-S-MR101N175-RX-MR74 N175-S-MR102N175-RX-MR75 N175-S-MR103N175-RX-MR76 N175-S-MR104N175-RX-MR77 N175-S-MR105N175-RX-MR78 N175-S-MR106N175-RX-MR79 N175-S-MR107N175-RX-MR80 N175-S-MR108N175-RX-MR81 N175-S-MR109N175-RX-MR82 N175-S-MR110N175-RX-MR83 N175-S-MR111N175-RX-MR84 N175-S-MR112N175-RX-MR85 N175-S-MR113N175-RX-MR86N175-RX-MR87N175-RX-MR88N175-RX-MR89N175-RX-MR90N175-R-MR24*N175-R-MR25*N175-R-MR26*
N175 Heavy Duty Round/Hex Square
* Round only
* Round only
* Round only 18
www.riten.com
19
Call 1-800-338-0027
®Multibore Collets, DIN 6343
Serrated bore
CA
B
Part No. A B C
M673 1.53” 2.42” 14.75°M677 1.77” 3.36” 14.75°J660 1.89” 4.27” 14.75°
Dimensions (inches)
.15 - .23 4 - 6
.23 - .31 6 - 8
.31 - .39 8 - 10
.39 - .47 10 - 12
.47 - .55 12 - 14
.55 - .63 14 - 16
.63 - .70 16 - 18
.70 - .78 18 - 20
.78 - .86 20 - 22
.86 - .94 22 - 24.94 - 1.02 24 - 26
1.02 - 1.10 26 - 281.10 - 1.18 28 - 301.18 - 1.25 30 - 32 1.25 - 1.33 32 - 341.33 - 1.41 34 - 361.41 - 1.49 36 - 381.49 - 1.57 38 - 401.57 - 1.65 40 - 421.65 - 1.73 42 - 441.73 - 1.81 44 - 461.81 - 1.89 46 - 481.89 - 1.92 48 - 501.92 - 2.04 50 - 522.04 - 2.12 52 - 542.12 - 2.20 54 - 562.20 - 2.28 56 - 582.28 - 2.36 58 - 602.36 - 2.44 60 - 622.44 - 2.52 62 - 642.52 - 2.59 64 - 662.59 - 2.67 66 - 682.67 - 2.75 68 - 702.75 - 2.83 70 - 722.83 - 2.91 72 - 742.91 - 2.99 74 - 762.99 - 3.07 76 - 783.07 - 3.14 78 - 80
Grip Range Inch mm
M673-R-6* M673-X-6* M673-S-6*M673-R-8* M673-X-8* M673-S-8*M673-R-10 M673-X-10 M673-S-10M673-R-12 M673-X-12 M673-S-12M673-R-14 M673-X-14 M673-S-14M673-R-16 M673-X-16 M673-S-16M673-R-18 M673-X-18 M673-S-18M673-R-20 M673-X-20 M673-S-20M673-R-22 M673-X-22 M673-S-22M673-R-24 M673-X-24 M673-S-24M673-R-26 M673-X-26 M673-S-26M673-R-28 M673-X-28 M673-S-28M673-R-30 M673-X-30 M673-S-30M673-R-32 M673-X-32M673-R-34 M673-X-34M673-R-36 M673-X-36M673-R-38M673-R-40M673-R-42
M673175E Compatible (4728)
Round Hex Square
* All collets marked with * are supplied with plain bore.Round bore collets are supplied with spiral serrations except those marked with *.Hexagonal and square collets are supplied with annular serrations except those marked with *.
M677-R-6* M677-X-6* M677-S-6*M677-R-8 M677-X-8 M677-S-8M677-R-10 M677-X-10 M677-S-10M677-R-12 M677-X-12 M677-S-12M677-R-14 M677-X-14 M677-S-14M677-R-16 M677-X-16 M677-S-16M677-R-18 M677-X-18 M677-S-18M677-R-20 M677-X-20 M677-S-20M677-R-22 M677-X-22 M677-S-22M677-R-24 M677-X-24 M677-S-24M677-R-26 M677-X-26 M677-S-26M677-R-28 M677-X-28 M677-S-28M677-R-30 M677-X-30 M677-S-30M677-R-32 M677-X-32 M677-S-32M677-R-34 M677-X-34 M677-S-34M677-R-36 M677-X-36 M677-S-36M677-R-38 M677-X-38 M677-S-38M677-R-40 M677-X-40 M677-S-40M677-R-42 M677-X-42 M677-S-42M677-R-44 M677-X-44M677-R-46 M677-X-46M677-R-48 M677-X-48M677-R-50 M677-X-50M677-R-52 M677-X-52M677-R-54M677-R-56M677-R-58M677-R-60
M677185E Compatible (4291)
Round Hex Square
J660-R-14 J660-X-14 J660-S-14J660-R-16 J660-X-16 J660-S-16J660-R-18 J660-X-18 J660-S-18J660-R-20 J660-X-20 J660-S-20J660-R-22 J660-X-22 J660-S-22J660-R-24 J660-X-24 J660-S-24J660-R-26 J660-X-26 J660-S-26J660-R-28 J660-X-28 J660-S-28J660-R-30 J660-X-30 J660-S-30J660-R-32 J660-X-32 J660-S-32J660-R-34 J660-X-34 J660-S-34J660-R-36 J660-X-36 J660-S-36J660-R-38 J660-X-38 J660-S-38J660-R-40 J660-X-40 J660-S-40J660-R-42 J660-X-42 J660-S-42J660-R-44 J660-X-44 J660-S-44J660-R-46 J660-X-46 J660-S-46J660-R-48 J660-X-48 J660-S-48J660-R-50 J660-X-50 J660-S-50J660-R-52 J660-X-52 J660-S-52J660-R-54 J660-X-54 J660-S-54J660-R-56 J660-X-56 J660-S-56J660-R-58 J660-X-58J660-R-60 J660-X-60J660-R-62 J660-X-62J660-R-64 J660-X-64J660-R-66 J660-X-66J660-R-68 J660-X-68J660-R-70J660-R-72J660-R-74J660-R-76J660-R-78J660-R-80
J660193E Compatible (H-47)
Round Hex Square
20
www.riten.com
® B-42 Spring Collets (inch)Round, Hex and Square
A C
BD
1/16” B42-R-1/16 B42-H-1/16 B42-S-1/16 1/8” B42-R-1/8 B42-H-1/8 B42-S-1/8
3/16” B42-R-3/16 B42-H-3/16 B42-S-3/161/4” B42-R-1/4 B42-H-1/4 B42-S-1/4
5/16” B42-R-5/16 B42-H-5/16 B42-S-5/163/8” B42-R-3/8 B42-H-3/8 B42-S-3/8
7/16” B42-R-7/16 B42-H-7/16 B42-S-7/161/2” B42-R-1/2 B42-H-1/2 B42-S-1/2
9/16” B42-R-9/16 B42-H-9/16 B42-S-9/165/8” B42-R-5/8 B42-H-5/8 B42-S-5/8
11/16” B42-R-11/16 B42-H-11/16 B42-S-11/163/4” B42-R-3/4 B42-H-3/4 B42-S-3/4
13/16” B42-R-13/16 B42-H-13/16 B42-S-13/167/8” B42-R-7/8 B42-H-7/8 B42-S-7/8
15/16” B42-R-15/16 B42-H-15/16 B42-S-15/161” B42-R-1 B42-H-1 B42-S-1
1-1/16” B42-R-1-1/16 B42-H-1-1/16 B42-S-1-1/161-1/8” B42-R-1-1/8 B42-H-1-1/8 B42-S-1-1/8
1-3/16” B42-R-1-3/16 B42-H-1-3/16 B42-S-1-3/161-1/4” B42-R-1-1/4 B42-H-1-1/4
1-5/16” B42-R-1-5/16 B42-H-1-5/161-3/8” B42-R-1-3/8 B42-H-1-3/8
1-7/16” B42-R-1-7/16 B42-H-1-7/161-1/2” B42-R-1-1/2 B42-H-1-1/2
1-9/16” B42-R-1-9/161-5/8” B42-R-1-5/8
Size Round Hex Square
A B C D
1.89” 3.7” 2.36” 15°
Dimensions (inches)
Emergency Collet: B42-EC
®B-42 Spring Collets (Metric)Round, Hex and Square
A C
BD
A B C D
48 94 60 15°
Dimensions (mm)
1.0mm B42-R-1.0 B42-H-1.0 B42-S-1.01.5mm B42-R-1.5 B42-H-1.5 B42-S-1.5 2.0mm B42-R-2.0 B42-H-2.0 B42-S-2.0 2.5mm B42-R-2.5 B42-H-2.5 B42-S-2.5 3.0mm B42-R-3.0 B42-H-3.0 B42-S-3.03.5mm B42-R-3.5 B42-H-3.5 B42-S-3.5 4.0mm B42-R-4.0 B42-H-4.0 B42-S-4.04.5mm B42-R-4.5 B42-H-4.5 B42-S-4.55.0mm B42-R-5.0 B42-H-5.0 B42-S-5.05.5mm B42-R-5.5 B42-H-5.5 B42-S-5.56.0mm B42-R-6.0 B42-H-6.0 B42-S-6.06.5mm B42-R-6.5 B42-H-6.5 B42-S-6.57.0mm B42-R-7.0 B42-H-7.0 B42-S-7.07.5mm B42-R-7.5 B42-H-7.5 B42-S-7.58.0mm B42-R-8.0 B42-H-8.0 B42-S-8.08.5mm B42-R-8.5 B42-H-8.5 B42-S-8.59.0mm B42-R-9.0 B42-H-9.0 B42-S-9.0 9.5mm B42-R-9.5 B42-H-9.5 B42-S-9.5
10.0mm B42-R-10.0 B42-H-10.0 B42-S-10.010.5mm B42-R-10.5 B42-H-10.5 B42-S-10.511.0mm B42-R-11.0 B42-H-11.0 B42-S-11.011.5mm B42-R-11.5 B42-H-11.5 B42-S-11.512.0mm B42-R-12.0 B42-H-12.0 B42-S-12.012.5mm B42-R-12.5 B42-H-12.5 B42-S-12.513.0mm B42-R-13.0 B42-H-13.0 B42-S-13.013.5mm B42-R-13.5 B42-H-13.5 B42-S-13.514.0mm B42-R-14.0 B42-H-14.0 B42-S-14.014.5mm B42-R-14.5 B42-H-14.5 B42-S-14.515.0mm B42-R-15.0 B42-H-15.0 B42-S-15.015.5mm B42-R-15.5 B42-H-15.5 B42-S-15.516.0mm B42-R-16.0 B42-H-16.0 B42-S-16.016.5mm B42-R-16.5 B42-H-16.5 B42-S-16.517.0mm B42-R-17.0 B42-H-17.0 B42-S-17.0 17.5mm B42-R-17.5 B42-H-17.5 B42-S-17.518.0mm B42-R-18.0 B42-H-18.0 B42-S-18.018.5mm B42-R-18.5 B42-H-18.5 B42-S-18.519.0mm B42-R-19.0 B42-H-19.0 B42-S-19.019.5mm B42-R-19.5 B42-H-19.5 B42-S-19.520.0mm B42-R-20.0 B42-H-20.0 B42-S-20.020.5mm B42-R-20.5 B42-H-20.5 B42-S-20.521.0mm B42-R-21.0 B42-H-21.0 B42-S-21.021.5mm B42-R-21.5 B42-H-21.5 B42-S-21.5
Size Round Hex Square
22.0mm B42-R-22.0 B42-H-22.0 B42-S-22.022.5mm B42-R-22.5 B42-H-22.5 B42-S-22.523.0mm B42-R-23.0 B42-H-23.0 B42-S-23.0 23.5mm B42-R-23.5 B42-H-23.5 B42-S-23.5 24.0mm B42-R-24.0 B42-H-24.0 B42-S-24.024.5mm B42-R-24.5 B42-H-24.5 B42-S-24.525.0mm B42-R-25.0 B42-H-25.0 B42-S-25.0 25.5mm B42-R-25.5 B42-H-25.5 B42-S-25.526.0mm B42-R-26.0 B42-H-26.0 B42-S-26.026.5mm B42-R-26.5 B42-H-26.5 B42-S-26.527.0mm B42-R-27.0 B42-H-27.0 B42-S-27.027.5mm B42-R-27.5 B42-H-27.5 B42-S-27.528.0mm B42-R-28.0 B42-H-28.0 B42-S-28.028.5mm B42-R-28.5 B42-H-28.5 B42-S-28.529.0mm B42-R-29.0 B42-H-29.0 B42-S-29.029.5mm B42-R-29.5 B42-H-29.5 B42-S-29.530.0mm B42-R-30.0 B42-H-30.0 B42-S-30.030.5mm B42-R-30.5 B42-H-30.531.0mm B42-R-31.0 B42-H-31.031.5mm B42-R-31.5 B42-H-31.532.0mm B42-R-32.0 B42-H-32.032.5mm B42-R-32.5 B42-H-32.533.0mm B42-R-33.0 B42-H-33.033.5mm B42-R-33.5 B42-H-33.534.0mm B42-R-34.0 B42-H-34.034.5mm B42-R-34.5 B42-H-34.535.0mm B42-R-35.0 B42-H-35.035.5mm B42-R-35.5 B42-H-35.536.0mm B42-R-36.0 B42-H-36.036.5mm B42-R-36.5 B42-H-36.537.0mm B42-R-37.0 B42-H-37.037.5mm B42-R-37.5 B42-H-37.538.0mm B42-R-38.0 B42-H-38.038.5mm B42-R-38.539.0mm B42-R-39.039.5mm B42-R-39.540.0mm B42-R-40.040.5mm B42-R-40.541.0mm B42-R-41.041.5mm B42-R-41.542.0mm B42-R-42.042.5mm B42-R-42.5
Size Round Hex Square
Emergency Collet: B42-EC
21
Call 1-800-338-0027
22
www.riten.com
®B-60 Spring Collets (inch & Metric)Round, Hex and Square
A C
BD
A B C D
2.6” 4.33” 3.31” 15°
Dimensions (inches)
Size Round Hex Square
1/16” B60-R-1/16 B60-H-1/16 B60-S-1/16 1/8” B60-R-1/8 B60-H-1/8 B60-S-1/8
3/16” B60-R-3/16 B60-H-3/16 B60-S-3/161/4” B60-R-1/4 B60-H-1/4 B60-S-1/4
5/16” B60-R-5/16 B60-H-5/16 B60-S-5/163/8” B60-R-3/8 B60-H-3/8 B60-S-3/8
7/16” B60-R-7/16 B60-H-7/16 B60-S-7/161/2” B60-R-1/2 B60-H-1/2 B60-S-1/2
9/16” B60-R-9/16 B60-H-9/16 B60-S-9/165/8” B60-R-5/8 B60-H-5/8 B60-S-5/8
11/16” B60-R-11/16 B60-H-11/16 B60-S-11/163/4” B60-R-3/4 B60-H-3/4 B60-S-3/4
13/16” B60-R-13/16 B60-H-13/16 B60-S-13/167/8” B60-R-7/8 B60H-7/8 B60-S-7/8
15/16” B60-R-15/16 B60-H-15/16 B60-S-15/161” B60-R-1 B60-H-1 B60-S-1
1-1/16” B60-R-1-1/16 B60-H-1-1/16 B60-S-1-1/161-1/8” B60-R-1-1/8 B60-H-1-1/8 B60-S-1-1/8
1-3/16” B60-R-1-3/16 B60-H-1-3/16 B60-S-1-3/161-1/4” B60-R-1-1/4 B60-H-1-1/4 B60-S-1/4
1-5/16” B60-R-1-5/16 B60-H-1-5/16 B60-S-1-5/161-3/8” B60-R-1-3/8 B60-H-1-3/8 B60-S-1-3/8
1-7/16” B60-R-1-7/16 B60-H-1-7/16 B60-S-1-7/161-1/2” B60-R-1-1/2 B60-H-1-1/2 B60-S-1/2
1-9/16” B60-R-1-9/16 B60-H-1-9/16 B60-S-1-9/161-5/8” B60-R-1-5/8 B60-H-1-5/8 B60-S-1-5/8
1-11/16” B60-R-1-11/16 B60-H-1-11/16 1-3/4” B60-R-1-3/4 B60-H-1-3/4
1-13/16” B60-R-1-13/16 B60-H-1-13/161-7/8” B60-R-1-7/8 B60-H-1-7/8
1-15/16” B60-R-1-15/16 B60-H-1-15/162” B60-R-2 B60-H-2
2-1/16” B60-R-2-1/162-1/8” B60-R-2-1/8
2-3/16” B60-R-1-3/162-1/4” B60-R-2-1/4
2-5/16” B60-R-1-5/16
Size Round Hex Square
Emergency Collet: B60-EC
1.0mm B60-R-1.0 B60-H-1.0 B60-S-1.01.5mm B60-R-1.5 B60-H-1.5 B60-S-1.5 2.0mm B60-R-2.0 B60-H-2.0 B60-S-2.0 2.5mm B60-R-2.5 B60-H-2.5 B60-S-2.5 3.0mm B60-R-3.0 B60-H-3.0 B60-S-3.03.5mm B60-R-3.5 B60-H-3.5 B60-S-3.5 4.0mm B60-R-4.0 B60-H-4.0 B60-S-4.04.5mm B60-R-4.5 B60-H-4.5 B60-S-4.55.0mm B60-R-5.0 B60-H-5.0 B60-S-5.05.5mm B60-R-5.5 B60-H-5.5 B60-S-5.56.0mm B60-R-6.0 B60-H-6.0 B60-S-6.06.5mm B60-R-6.5 B60-H-6.5 B60-S-6.57.0mm B60-R-7.0 B60-H-7.0 B60-S-7.07.5mm B60-R-7.5 B60-H-7.5 B60-S-7.58.0mm B60-R-8.0 B60-H-8.0 B60-S-8.08.5mm B60-R-8.5 B60-H-8.5 B60-S-8.59.0mm B60-R-9.0 B60-H-9.0 B60-S-9.0 9.5mm B60-R-9.5 B60-H-9.5 B60-S-9.5
10.0mm B60-R-10.0 B60-H-10.0 B60-S-10.010.5mm B60-R-10.5 B60-H-10.5 B60-S-10.511.0mm B60-R-11.0 B60-H-11.0 B60-S-11.011.5mm B60-R-11.5 B60-H-11.5 B60-S-11.512.0mm B60-R-12.0 B60-H-12.0 B60-S-12.012.5mm B60-R-12.5 B60-H-12.5 B60-S-12.513.0mm B60-R-13.0 B60-H-13.0 B60-S-13.013.5mm B60-R-13.5 B60-H-13.5 B60-S-13.514.0mm B60-R-14.0 B60-H-14.0 B60-S-14.014.5mm B60-R-14.5 B60-H-14.5 B60-S-14.515.0mm B60-R-15.0 B60-H-15.0 B60-S-15.015.5mm B60-R-15.5 B60-H-15.5 B60-S-15.516.0mm B60-R-16.0 B60-H-16.0 B60-S-16.016.5mm B60-R-16.5 B60-H-16.5 B60-S-16.517.0mm B60-R-17.0 B60-H-17.0 B60-S-17.0 17.5mm B60-R-17.5 B60-H-17.5 B60-S-17.518.0mm B60-R-18.0 B60-H-18.0 B60-S-18.018.5mm B60-R-18.5 B60-H-18.5 B60-S-18.519.0mm B60-R-19.0 B60-H-19.0 B60-S-19.019.5mm B60-R-19.5 B60-H-19.5 B60-S-19.520.0mm B60-R-20.0 B60-H-20.0 B60-S-20.020.5mm B60-R-20.5 B60-H-20.5 B60-S-20.521.0mm B60-R-21.0 B60-H-21.0 B60-S-21.021.5mm B60-R-21.5 B60-H-21.5 B60-S-21.5
®B-60 Spring Collets (Metric)Round, Hex and Square
A C
BD
A B C D
66 110 84 15°
Dimensions (mm)
22.0mm B60-R-22.0 B60-H-22.0 B60-S-22.022.5mm B60-R-22.5 B60-H-22.5 B60-S-22.523.0mm B60-R-23.0 B60-H-23.0 B60-S-23.0 23.5mm B60-R-23.5 B60-H-23.5 B60-S-23.5 24.0mm B60-R-24.0 B60-H-24.0 B60-S-24.024.5mm B60-R-24.5 B60-H-24.5 B60-S-24.525.0mm B60-R-25.0 B60-H-25.0 B60-S-25.0 25.5mm B60-R-25.5 B60-H-25.5 B60-S-25.526.0mm B60-R-26.0 B60-H-26.0 B60-S-26.026.5mm B60-R-26.5 B60-H-26.5 B60-S-26.527.0mm B60-R-27.0 B60-H-27.0 B60-S-27.027.5mm B60-R-27.5 B60-H-27.5 B60-S-27.528.0mm B60-R-28.0 B60-H-28.0 B60-S-28.028.5mm B60-R-28.5 B60-H-28.5 B60-S-28.529.0mm B60-R-29.0 B60-H-29.0 B60-S-29.029.5mm B60-R-29.5 B60-H-29.5 B60-S-29.530.0mm B60-R-30.0 B60-H-30.0 B60-S-30.030.5mm B60-R-30.5 B60-H-30.5 B60-S-30.531.0mm B60-R-31.0 B60-H-31.0 B60-S-31.031.5mm B60-R-31.5 B60-H-31.5 B60-S-31.532.0mm B60-R-32.0 B60-H-32.0 B60-S-32.032.5mm B60-R-32.5 B60-H-32.5 B60-S-32.533.0mm B60-R-33.0 B60-H-33.0 B60-S-33.033.5mm B60-R-33.5 B60-H-33.5 B60-S-33.534.0mm B60-R-34.0 B60-H-34.0 B60-S-34.034.5mm B60-R-34.5 B60-H-34.5 B60-S-34.535.0mm B60-R-35.0 B60-H-35.0 B60-S-35.035.5mm B60-R-35.5 B60-H-35.5 B60-S-35.536.0mm B60-R-36.0 B60-H-36.0 B60-S-36.036.5mm B60-R-36.5 B60-H-36.5 B60-S-36.537.0mm B60-R-37.0 B60-H-37.0 B60-S-37.037.5mm B60-R-37.5 B60-H-37.5 B60-S-37.538.0mm B60-R-38.0 B60-H-38.0 B60-S-38.038.5mm B60-R-38.5 B60-H-38.5 B60-S-38.539.0mm B60-R-39.0 B60-H-39.0 B60-S-39.039.5mm B60-R-39.5 B60-H-39.5 B60-S-39.540.0mm B60-R-40.0 B60-H-40.0 B60-S-40.040.5mm B60-R-40.5 B60-H-40.5 B60-S-40.541.0mm B60-R-41.0 B60-H-41.0 B60-S-41.0
Size Round Hex Square
41.5mm B60-R-41.5 B60-H-41.5 B60-S-41.542.0mm B60-R-42.0 B60-H-42.0 B60-S-42.042.5mm B60-R-42.5 B60-H-42.5 B60-S-42.543.0mm B60-R-43.0 B60-H-43.043.5mm B60-R-43.5 B60-H-43.544.0mm B60-R-44.0 B60-H-44.0 44.5mm B60-R-44.5 B60-H-44.5 45.0mm B60-R-45.0 B60-H-45.045.5mm B60-R-45.5 B60-H-45.546.0mm B60-R-46.0 B60-H-46.0 46.5mm B60-R-46.5 B60-H-46.547.0mm B60-R-47.0 B60-H-47.047.5mm B60-R-47.5 B60-H-47.548.0mm B60-R-48.0 B60-H-48.048.5mm B60-R-48.5 B60-H-48.549.0mm B60-R-49.0 B60-H-49.049.5mm B60-R-49.5 B60-H-49.550.0mm B60-R-50.0 B60-H-50.050.5mm B60-R-50.5 B60-H-50.551.0mm B60-R-51.0 B60-H-51.051.5mm B60-R-51.5 B60-H-51.552.0mm B60-R-52.0 B60-H-52.052.5mm B60-R-52.5 B60-H-52.553.0mm B60-R-53.053.5mm B60-R-53.554.0mm B60-R-54.054.5mm B60-R-54.555.0mm B60-R-55.055.5mm B60-R-55.556.0mm B60-R-56.056.5mm B60-R-56.557.0mm B60-R-57.057.5mm B60-R-57.558.0mm B60-R-58.058.5mm B60-R-58.559.0mm B60-R-59.059.5mm B60-R-59.560.0mm B60-R-60.060.5mm B60-R-60.5
Size Round Hex Square
Emergency Collet: B60-EC23
Call 1-800-338-0027
Tel: 800-338-0027 Website: www.Riten.com Fax: 800-338-0717
D
CE
A1 MAX.A2 MIN.
B1 MAX.B2 MIN.
DRAWTUBE CONNECTOR SPECIFICATIONS Spindle Nose Without Chuck A Custom Threaded Connector is required to connect the draw tube of your machine to the collet chuck. For proper actuation, please complete this form as accurately as possible. THD
Company: ____________________
Contact: _____________________
Tel: _____________________
Collet Chuck __________________________
Purchase Order ________________________
Machine Make & Model _________________
_____________________________________
Sub Spindle / Main Spindle (Circle One)
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ A1 – Tube Extended _________________ THD _____________________________
A2 – Tube Retracted _________________ Internal / External (circle one)
B1 – Tube Extended _________________ Pitch _____________________________
B2 – Tube Retracted _________________ Length ____________________________
C – Counterbore Dia _________________ D – Counterbore Depth_______________
A
B
®
Accuracy Chart
5C, 16C and R8 Collets
1.0mm0.039”
1.0mm - 1.5mm0.039” - 0.059”
1.5mm - 3.0mm0.059” - 0.118”
3.0mm - 6.0mm0.118” - 0.236”
6.0mm - 10.0mm0.236” - 0.394”
10.0mm - 19.0mm0.394” - 0.748”
19.0mm - 25.4mm0.748” - 1.0”
25.4mm - 32mm1.0” - 1.26”
32mm - 50.8mm1.26” - 2.0”
Over 50.8mm2.0”
0.007mm 3.0mm0.0003” 0.125”
0.010mm 6.5mm0.0004” 0.250”
0.020mm 9.5mm0.0004” 0.375”
0.010mm 16mm0.0004” 0.625”
0.010mm 25.5mm0.0004” 1.0”
0.015mm 38.0mm0.0006” 1.5”
0.015mm 51.0mm0.0006” 2.0”
0.020mm 63.5mm0.0008” 2.5”
0.020mm 76.0mm0.0008” 3.0”
0.020mm 101.5mm0.0008” 4.0”
Bore Size A BCenter or A/Flat Round Test Length
25
Call 1-800-338-0027
A
B
®
Accuracy Charts
Multibore and B Type Spring Collets
1.0mm0.039”
1.0mm - 1.5mm0.039” - 0.059”
1.5mm - 3.0mm0.059” - 0.118”
3.0mm - 6.0mm0.118” - 0.236”
6.0mm - 10.0mm0.236” - 0.394”
10.0mm - 19.0mm0.394” - 0.748”
19.0mm - 25.4mm0.748” - 1.0”
25.4mm - 32mm1.0” - 1.26”
32mm - 50.8mm1.26” - 2.0”
Over 50.8mm2.0”
0.015mm 0.046mm 3.0mm0.0006” 0.0018” 0.125”
0.020mm 0.060mm 6.5mm0.0008” 0.0024” 0.250”
0.020mm 0.060mm 9.5mm0.0008” 0.0024” 0.375”
0.020mm 0.060mm 16mm0.0008” 0.0024” 0.625”
0.020mm 0.060mm 25.5mm0.0008” 0.0024” 1.0”
0.030mm 0.091mm 38.0mm0.0012” 0.0036” 1.5”
0.030mm 0.091mm 51.0mm0.0012” 0.0036” 2.0”
0.040mm 0.120mm 63.5mm0.0016” 0.0048” 2.5”
0.040mm 0.120mm 76.0mm0.0016” 0.0048” 3.0”
0.040mm 0.120mm 101.5mm0.0016” 0.0048” 4.0”
Bore Size A BCenter or A/Flat Round Hex & Square Test Length
26
www.riten.com
1.0mm0.039”
1.0mm - 1.5mm0.039” - 0.059”
1.5mm - 3.0mm0.059” - 0.118”
3.0mm - 6.0mm0.118” - 0.236”
6.0mm - 10.0mm0.236” - 0.394”
10.0mm - 19.0mm0.394” - 0.748”
19.0mm - 25.4mm0.748” - 1.0”
25.4mm - 32mm1.0” - 1.26”
32mm - 50.8mm1.26” - 2.0”
Over 50.8mm2.0”
0.015mm 0.046mm 3.0mm0.0006” 0.0018” 0.125”
0.020mm 0.060mm 6.5mm0.0008” 0.0024” 0.250”
0.020mm 0.060mm 9.5mm0.0008” 0.0024” 0.375”
0.020mm 0.060mm 16mm0.0008” 0.0024” 0.625”
0.020mm 0.060mm 25.5mm0.0008” 0.0024” 1.0”
0.030mm 0.091mm 38.0mm0.0012” 0.0036” 1.5”
0.030mm 0.091mm 51.0mm0.0012” 0.0036” 2.0”
0.040mm 0.120mm 63.5mm0.0016” 0.0048” 2.5”
0.040mm 0.120mm 76.0mm0.0016” 0.0048” 3.0”
0.040mm 0.120mm 101.5mm0.0016” 0.0048” 4.0”
Bore Size A BCenter or A/Flat Round Hex & Square Test Length
Multibore and DIN 6343Multibore Collets
B
A
B Type Spring Collets
RITEN INDUSTRIES WARRANTY – DISCLAIMER OF WARRANTY
Riten warrants that its products shall be free from defects in material andworkmanship under normal use when correctly installed and maintained.This warranty of quality shall terminate one year after delivery of the productsto the buyer and shall not apply to products which have been subjected toaccident, misuse, abuse, neglect or improper storage, handling or maintenance.
THIS STATEMENT OF WARRANTY IS IN LIEU OF ALL OTHER WARRANTIESWITH RESPECT TO THE PRODUCTS, EXPRESS OR IMPLIED, WHETHERWRITTEN OR ORAL, STATUTORY, BY OPERATION OF LAW OR OTHER-WISE. THERE IS NO – AND RITEN DISCLAIMS ANY – WARRANTY OF MER-CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ORWARRANTY ARISING BY USAGE OF TRADE OR PERFORMANCE ORCOURSE OF DEALING.
Any affirmation of fact, description, sample, model or promise made or providedby Riten, other than the aforementioned Statement of Warranty, shall not createa warranty and shall not be part of the basis of the parties’ bargain.
LIMITATION OF DAMAGES – DISCLAIMER OF LIABILITY
BUYER’S SOLE AND EXCLUSIVE REMEDY AGAINST RITEN FOR BREACHOF WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OFANY NONCONFORMING PRODUCTS, PURSUANT TO THE ABOVE STATE-MENT OF WARRANTY.
RITEN SHALL NOT BE LIABLE TO BUYER OR ANY OTHER PERSON FORANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARYLOSSES, DAMAGES OR EXPENSES, DIRECTLY OR INDIRECTLY ARISINGOUT OF THE SALE, HANDLING OR USE OF THE PRODUCTS OR FROMANY OTHER CAUSE RELATING THERETO. RITEN’S LIABILITY WHETHERBASED ON CONTRACT, WARRANTY OR TORT (INCLUDING BUT NOT LIM-ITED TO NEGLIGENCE AND STRICT LIABILITY) OR OTHERWISE IS LIMIT-ED TO, AT RITEN’S OPTION, THE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS OR THE REPAYMENT OF, OR CREDITINGBUYER WITH, AN AMOUNT EQUAL TO THE PURCHASE PRICE UPONRETURN OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IF RITENPERFORMS UNDER THIS LIMITED REMEDY, SUCH LIMITED REMEDYSHALL NOT HAVE FAILED ITS ESSENTIAL PURPOSE.
UIC #662503, FSC #3460, CAGE #05467, Harmonized Schedule B, 8466.20.1010, 8466.20.1090
Quality workholding since 1933
Riten Industries, Inc.1100 Lakeview Avenue ■ P.O. Box 340
Washington Court House, OH 43160 USA740-335-5353 ■ FAX 740-335-4622
E-mail: sales@riten.comwww.riten.com
®
Distributed By:
Workholding solutions, not excuses!
Live and Dead CentersThe world’s largest selection
Face DriversSingle-operation machining
Super Duty Live CentersFor workpieces up to
450,000 lbs.