3D Design Procedures & Practice

1

Centenary Building My Layers

3D Design Procedures & Practice

2

Setting Paper Space

Right click then hit ‘Page Setup Manager’.

3D Design Procedures & Practice

3

To change the plot scale click on the edit button

Check the (paper) plot size here.

3D Design Procedures & Practice

4

Make sure that scale is 1:1 mm if so then paper space should be ok.

3D Design Procedures & Practice

5

Location plan

I got an image of the location plan from Blackboard and I imported it into Auto Cad. Floor plan

I started drawing the floor plan here. As you can see I was still trying to workout where things go and if the measurements were right.

3D Design Procedures & Practice

6

Doors

The measurements looked fine so I went on to the doors. I drew a small box, line and a circle to create the door. Trim tool

I trimmed the unwanted parts of the circle

3D Design Procedures & Practice

7

Mirror tool

After I mirrored the door I then trimmed the excess off both doors.

I followed the same process to draw the

double doors but this time I did not trim

anything.

3D Design Procedures & Practice

8

Fillet

Completed Floor Plan

I noticed that some of my measurements were wrong, so I went back to the site to double-check them.

3D Design Procedures & Practice

9

Copy tool

Selecting objects

Selecting point of displacement

3D Design Procedures & Practice

10

Placing copies

Endpoint

3D Design Procedures & Practice

11

Extend EX – Keyboard shortcut To Execute

• Select object(s) or (select all)

• Enter or spacebar • (Fence/Crossing/Project/Edge/Undo)

At this point I simply selected the objects that I wanted to extend by drawing a green box around them from right – left.

3D Design Procedures & Practice

12

Green box

• Enter or spacebar to end command

3D Design Procedures & Practice

13

Completed Floor Plan: After double checking measurements

Planning layout: Long Section Offset: stairs

3D Design Procedures & Practice

14

Drawing steps I changed the color of the stairs so that I could see them better.

Stairs

Rails

Landing

3D Design Procedures & Practice

15

Array AR – Keyboard shortcut I  created  a  path  array

This toolbar enabled me to edit the path.

The hotgrips enabled me to move the steps

3D Design Procedures & Practice

16

Rails

Trim

Copy

3D Design Procedures & Practice

17

Detailed component

3D Design Procedures & Practice

18

Isometric drawing To set isometric mode:

• Right click on the grid in the status bar • Click on settings

This box should appear

3D Design Procedures & Practice

19

• Choose Isometric snap

Another way of doing this is by right clicking on ‘object snap’ in the status bar, settings and then ‘snap and grid’. Lift

Drawn using polyline

3D Design Procedures & Practice

20

Drawing walls

Drawing window Extending line

I made a mistake with the measurements when drawing this

wall. I realized later on and drew it again at

the correct size.

3D Design Procedures & Practice

21

Trimming & Extending

I trimmed the lines I did not need and extended the wall. The result is show below

3D Design Procedures & Practice

22

Fillet: Fire door F – Keyboard shortcut

3D Design Procedures & Practice

23

Array of windows Fillet using radius

I used the fillet to round off the edges of the windows

3D Design Procedures & Practice

24

Completed array of windows

Landing leading to second floor

3D Design Procedures & Practice

25

Steps

Rails: Ground floor

I started drawing the rails here

3D Design Procedures & Practice

26

I used the same method as I did for the long section when drawing the rails.

3D Design Procedures & Practice

27

Completed isometric

Axonometric floor plan

1. Copy the image

3D Design Procedures & Practice

28

2. Select object from right to left

3. RO – Rotate to 45 degrees and make sure cursor is on the right. A preview of the image should appear.

3D Design Procedures & Practice

29

4. Drawing line to make wall Copy I can copy and paste to save time.

3D Design Procedures & Practice

30

The windows, doors and rails were the last things that I did in this drawing because they had more details. The Axonometric so far

3D Design Procedures & Practice

31

Trimming

I trimmed overlapping area’s in this case the windows. Completed Axonometric

3D Design Procedures & Practice

32

Hatching I left the hatching till last so that I could focus on drawing. Floor plan

Long section

3D Design Procedures & Practice

33

Short section

Axonometric

3D Design Procedures & Practice

34

Dimensioning To change the settings of the dimension use the DIMSTYLE command to bring up dimension style manager.

Floor plan in viewport

3D Design Procedures & Practice

35

All my drawings

Tools I used PLine: PL – Keyboard shortcut

• Specify first point • Specify next point

Trim: TR – Keyboard shortcut

• Specify object or select all • Enter/Spacebar

Mirror: MI – Keyboard shortcut

• Select objects • Specify first point of mirror line • Specify second point of mirror line • Erase source object – Yes / No

3D Design Procedures & Practice

36

Copy: CO – Keyboard shortcut

• Select objects • Specify base point or (Displacement /mode) • Specify second point or (Array) • Enter/spacebar

Extend: EX – Keyboard shortcut

• Select object or (select all) • Select object to extend

Offset: O – keyboard shortcut

• Specify offset distance • Specify object to offset or (exit/undo)

Fillet: F - Keyboard shortcut

• Select first object or (undo/polyline/Radius/Trim/Multiple) • Select second object or shift-select to apply corner or (Radius) • Enter or Spacebar to end command

Array: AR – Keyboard shortcut

• Select objects • Enter or spacebar • Enter array type • Select grip to array

3D Design Procedures & Practice

37

Client presentation

Hand rendered

I added a map of the area

3D Design Procedures & Practice

38

Axonometric and floor plan