Post on 15-Oct-2021
CAPS,PLUGS
AND GLIDES
24Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
VINYL-DIPPED CAPS AND PROTECTORS
SHORT CAPS
Part NumbersPlease use the following system for part numbers:
VSC [ID in decimals] X [Length in decimals] . For instance, a cap with ID of .062" and length of 3/8" would bepart number VSC 062X.375.
Stock SizesMost sizes stocked in 1/2", 1" and 1-1/2" lengths. Short Caps
are also available in almost any length in .062" increments witha minimum length of .187". For sizes not shown here, pleasesee Standard Short Cap and L-Cap sections.
LONG CAPS
Long Caps come in diameters ranging from 3/16" through 3-1/2". Most sizes areavailable in inside lengths up to 5-1/4", in1/16" increments and many are available to8" lengths. Excellent as pipe protectors,grips, caps for boiler tubes, connectors andcable end seals. Tough and durable, LongCaps are also used in many masking applications.
.062, .080 X 3/8, 1/2
.093 X 3/8, 1/2, 3/4
.112 X 3/8, 1/2, 3/4, 1
.125, .137, .142, X 1/2, 3/4, 1, 1-1/2
.156, .172, .187,
.207, .234, .250,
.281, .313, .343,
.375, .406, .437,
.468, .500, .531.
.562, .625, .687,
.750, .812, .843,
.875, .937, 1.000
1.062 X 11.187, 1.375, X 1-1/21.625, 1.750,2.000, 2.250, 2.750
Flexible vinyl Short Caps fit snuglywithout cracking or splitting. They haveexcellent insulation qualities and resistweather, moisture and chemicals.Suitable for almost any applicationincluding colour coding, thread protec-tors, insulators, seals, cable ends,electronic wiring, tools, decorations,masks, etc.
Hundreds of stock sizes. Others canbe produced to your specs wherequantities warrant.
Also available in high temperature resistant material. Hi-temp series hasbeen used at up to 440oF for extendedperiods without breakdown.
*Use an undersized diameter for a tight fit. For example, if your outside diameter is 1/2",use a .437 cap.
Inside Diameters* X Inside Lengths Inside Diameters* X Inside Lengths
Stock colours: Black or red.
In-Stock ProgrammeThe following sizes can be ordered from stock in black or red. Non-stock colours: white, blue, green, orange, yellow and gray.
25Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
VINYL-DIPPED CAPS AND PROTECTORS CONTINUED
NOTE: We suggest a slightlyundersized diameter for a tight fitdue to the softness and flexibility ofthese caps. For example, if the ODis .500, use a .437 Short Cap.
Inside Dia.A
Max. InsideLength B
Nominal WallThickness C
.062
.080
.093
.112
.125
.137
.142
.151
.156
.172
.187
.207
.219
.234
.240
.250
.281
.313
.331
.343
.375
.406
.420
.437
.468
.500
.531
.562
.625
.687
.730
.750
.750
.750
.7501.0001.500
1.5001.5001.5001.5001.500
1.5001.5001.5001.5001.500
1.5002.5001.5001.5002.500
1.5002.5001.5001.5002.500
1.5002.5001.5001.5001.5001.5001.500
.028
.028
.028
.030
.033
.033
.033
.038
.038
.038
.038
.038
.038
.038
.038
.042
.042
.042
.042
.042
.042
.055
.055
.055
.055
.055
.060
.060
.060
.060
.060
.060
VSC 062X.750VSC 080X.750VSC 093X.750VSC 112X1.000VSC 125X1.500
VSC 137X1.500VSC 142X1.500VSC 151X1.500VSC 156X1.500VSC 172X1.500
VSC 187X1.500VSC 207X1.500VSC 219X1.500VSC 234X1.500VSC 240X1.500
VSC 250X1.500VSC 281X2.500VSC 313X1.500VSC 331X1.500VSC 343X2.500
VSC 375X1.500VSC 406X2.500VSC 420X1.500VSC 437X1.500VSC 468X2.500
VSC 500X1.500VSC 531X2.500VSC 562X1.500VSC 625X1.500VSC 687X1.500VSC 730X1.500VSC 750X1.500
Part No.Inside Dia.
AMax. InsideLength B
Nominal WallThickness C
.812
.843
.875
.937
.950
1.0001.0621.1251.1871.250
1.3751.5001.6251.6871.750
1.8752.0002.1252.2502.375
2.5002.6252.7503.0003.125
3.2503.5003.6254.0004.750
1.5001.5001.5001.5001.500
1.5001.5001.5001.5001.500
1.5001.5001.5001.5001.500
2.0001.5001.7501.5001.500
1.5001.7501.5001.5001.750
1.5001.5001.7501.7502.000
.060
.060
.060
.060
.060
.060
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
VSC 812X1.500VSC 843X1.500VSC 875X1.500VSC 937X1.500VSC 950X1.500
VSC 1000X1.500VSC 1062X1.500VSC 1125X1.500VSC 1187X1.500VSC 1250X1.500
VSC 1375X1.500VSC 1500X1.500VSC 1625X1.500VSC 1687X1.500VSC 1750X1.500
VSC 1875X2.000VSC 2000X1.500VSC 2125X1.750VSC 2250X1.500VSC 2375X1.500
VSC 2500X1.500VSC 2625X1.750VSC 2750X1.500VSC 3000X1.500VSC 3125X1.750
VSC 3250X1.500VSC 3500X1.500VSC 3625X1.750VSC 4000X1.750VSC 4750X2.000
Part No.
Standard colours: Black, red.Also available in white, blue, green, orange, yellow, gray.
STANDARD SHORT CAPS
26Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
TAPERED CAPS AND PLUGSTapered and flexible for easy installation and removal, these
provide a snug fit as either a cap or plug. Protect threads andkeep dirt and moisture out of pipes, valves, tubes, etc.
When using as a cap, “I” dimension should be at least .020"
per inch less than diameter to be capped. When using as aplug, “L” dimension should be at least .020” per inch larger thanopening. Larger diameters may require more interference.
NIA 234-ANIA 235-CNIA 235-TNIA 235-VNIA 236-X
NIA 236-LNIA 237-YNIA 229-ZNIA 238-DNIA 1193
NIA 239-ENIA 181NIA 240NIA 189-CNIA 189
NIA 189-2NIA 241NIA 241-SNIA 188NIA 242
NIA 242-2NIA 243NIA 191NIA 203NIA 710
1/8
1/4
3/8
1/8
1/4
3/8
1/2
5/163/8
29/643/8
15/32
15/321/29/169/1611/16
19/325/8
21/3211/1611/16
23/323/43/4
25/3227/32
27/327/87/8
15/1655/64
13/3213/3211/3211/323/8
13/3213/32
3/813/3229/32
13/3213/3213/325/1615/32
15/3215/3211/321/2
17/32
17/321/2
17/3219/323/16
.052
.110
.146
.150
.175
.205
.235
.267
.298
.375
.328
.358
.384
.415
.408
.436
.469
.490
.487
.518
.549
.578
.614
.627
.688
.117
.177
.211
.210
.239
.273
.303
.333
.364
.375
.395
.422
.448
.485
.484
.504
.544
.550
.569
.606
.634
.665
.691
.723
.743
.116
.174
.210
.209
.239
.267
.299
.331
.362
.437
.392
.422
.448
.477
.472
.500
.533
.552
.551
.580
.610
.642
.678
.691
.750
.181
.241
.275
.269
.303
.335
.367
.397
.428
.437
.459
.486
.512
.547
.548
.568
.608
.612
.633
.668
.695
.729
.755
.787
.805
25,00030,00010,00015,00045,000
20,00025,00015,00020,000
7,500
20,00020,000
7,0007,500
12,000
10,00010,00015,00010,000
7,000
7,5007,5007,5005,0007,500
Part No. Cap Plug G H I J K L Std. Pkg .
N.P.T. Sizes
Minimums available on request.Orange Low Density Polyethylene. Mil Spec (MIL-C-5501/7)
Continued
27Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
NIA 245NIA 246NIA 204NIA 247NIA 192-2-C
NIA 192-1NIA 192-2NIA 277NIA 248NIA 709
NIA 249-1NIA 249-2NIA 249NIA 249-WNIA 153
NIA 193NIA 250-SNIA 250-S WNIA 250NIA 1153
NIA 251NIA 205NIA 252NIA 253-SNIA 253
NIA 727NIA 253-2NIA 254-SNIA 254NIA 194
NIA 195-FNIA 195-SNIA 255NIA 1972NIA 196
NIA 206NIA 911NIA 256NIA 806NIA 257
NIA 258NIA 258-SNIA 259NIA 260NIA 261
1/2
3/4
1
1-1/41-1/4
1-1/2
3/4
3/43/4
1
1-1/4
1-1/21-1/2
11
1-1/161-1/81-1/8
1-1/81-1/8
1-5/321-5/321-5/16
1-1/41-1/4
1-9/321-7/161-5/16
1-13/321-7/161-43/641-7/161-3/8
1-1/21-1/21-1/21-5/81-5/8
1-3/41-49/64
1-3/41-3/4
1-25/32
1-7/81-7/8
1-15/162-1/32
2
2-5/322-3/82-1/8
2-13/642-1/4
2-1/42-19/322-5/162-7/162-19/32
19/3219/3221/32
5/821/32
3/421/32
1/223/32
7/8
1/21-1/32
3/43/4
25/32
25/3221/3221/32
3/49/16
3/427/32
3/417/32
3/4
51/6415/16
7/83/43/4
25/325/83/43/4
25/32
143/64
13/41
13/83/4
1-1/321
.663
.688
.739
.755
.790
.805
.805
.878
.855
.940
.918
.890
.903
.918
.933
1.0291.1161.1131.1151.115
1.1621.1751.2311.2861.248
1.3401.2821.3841.3871.455
1.4981.5141.5691.6641.688
1.7431.7851.7831.8851.839
1.9172.0361.9532.0002.093
.761
.785
.848
.869
.894
.909
.909
.971
.980
.960
.9851.0301.0281.0471.080
1.1551.2231.2221.2221.190
1.2901.3001.2951.4011.401
1.4201.4501.5371.5371.538
1.6201.6281.6861.7941.818
1.8741.8951.9362.0002.014
2.0692.0762.0832.1742.265
.727
.752
.803
.819
.854
.869
.869
.942
.9151.020
.980
.950
.967
.975
.997
1.0931.1801.1751.1791.276
1.2261.2331.2921.3501.312
1.4351.3441.4471.4511.519
1.5601.5741.6331.7201.752
1.8071.8651.8471.9501.903
1.9812.1002.0172.0702.157
5,0005,0003,5003,0002,500
2,5002,5003,5002,5001,500
3,0001,5002,5002,0004,000
1,5002,5001,0001,5002,000
1,5001,5001,5002,0001,500
1,0001,0001,0001,0003,500
3,5005,0001,0003,5003,500
1,0002,500
5002,5001,000
5001,000
5001,800
500
.825
.849
.912
.933
.958
.973
.9731.0351.0401.040
1.0491.0901.0921.1041.144
1.2191.2801.2841.2861.312
1.3541.3581.3561.4651.465
1.5001.5071.6001.6011.602
1.6821.6881.7501.8501.882
1.9381.9752.0002.0652.078
2.1332.1402.1472.2442.329
Part No. Cap Plug G H I J K L Std. Pkg.N.P.T. Sizes
Minimums available on request.Orange Low Density Polyethylene. Mil Spec (MIL-C-5501/7).
Continued
TAPERED CAPS & PLUGS CONTINUED
28Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
TAPERED CAPS & PLUGS CONTINUED
NIA 1230NIA 262NIA 207NIA 708NIA 263
NIA 264NIA 265NIA 267NIA 266NIA 199NIA 2156
1,500500500
2,000500
500500500500500500
2.4002.4082.4642.4642.604
2.6452.6502.6902.7502.7902.790
2.2802.1292.3002.3002.396
2.4822.3112.5612.4572.6412.641
2.3362.3442.4002.3832.540
2.5812.5862.6262.6862.7282.728
2.2162.0652.2362.2202.332
2.4182.2472.4972.3932.5792.579
3/41-1/32
13/4
1-5/32
21/321
3/41
25/321/2
2-51/642-17/32
2-5/82-21/322-13/16
2-25/322-25/32
2-7/82-7/8
2-31/322-31/32
2-1/2
2
Part No. Cap Plug G H I J K L Std. Pkg.N.P.T. Sizes
Minimums available on request.
NIA 862NIA 268NIA 208NIA 2046NIA 228NIA 269
NIA 270NIA 200NIA 209NIA 338NIA 341
NIA 339NIA 303NIA 340NIA 405NIA 406
NIA 342NIA 343NIA 407NIA 344NIA 345
NIA 346NIA 351NIA 352NIA 365NIA 366
NIA 367NIA 368NIA 369NIA 370NIA 390
2.8702.9822.9903.1033.1593.244
3.3673.4523.5623.6023.732
3.8023.9204.0744.1404.459
4.6224.8525.1005.4945.624
5.8746.1846.5646.7747.124
7.6567.8468.1468.736
10.125
2.7902.9182.9263.0413.0793.174
3.2973.3823.4923.5423.658
3.7223.8403.9944.0604.379
4.5424.7825.0205.3855.544
5.7946.0946.4946.6347.044
7.5807.7628.0528.6029.985
2.6262.7862.6562.9152.9162.910
3.0183.2503.2003.4063.478
3.5963.7103.8483.9404.134
4.2884.5684.9005.2175.386
5.6065.9186.3286.5286.968
7.2547.5747.8748.5349.810
23/323/41
3/415/32
1
13/4
1-1/83/41
3/43/43/43/4
15/16
17/8
11/167/81
11
7/81-1/2
1
111
1-1/21
3-1/163-1/43-1/8
3-11/323-13/323-3/8
3-1/23-5/8
3-11/163-7/8
4
44-1/84-3/8
4-17/324-15/16
55-1/45-7/165-7/86-1/8
6-1/46-5/8
6-15/167-3/167-5/8
7-15/168-1/88-3/89-1/810-1/2
2-1/2
3
3-1/2
4
5
6
Minimums available on request.
Part No. Cap Plug G H I J K L Std. Pkg .N.P.T. Sizes
500250500
1,200500250
250500250250700
250250700600400
400400450250250
200200200100200
300160160100
60
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32" per inch.
Heat distortion temperatures are as follows: Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
Orange Low Density Polyethylene. Mil Spec (MIL-C-5501/7).
Orange Low Density Polyethylene
M.040.030.032.033.045.035
.035
.035
.035
.045
.040
.040
.040
.040
.040
.060
.045
.060
.060
.060
.040
.065
.045
.065
.065
.065
.065
.070
.070
.070
.070
2.7062.8502.7202.9752.9962.980
3.0883.3203.2703.4663.552
3.6763.7903.9284.0204.214
4.3684.6384.9805.3265.466
5.6966.0086.3986.6687.048
7.3387.6587.9688.6689.950
3
3-1/2
4
5
6
Extra Large Tapered Caps & Plugs
29Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
VINYL-DIPPED CAPS AND PROTECTORS
RECTANGULAR VINYL CLOSURES
R-Caps (Rectangular Caps) offer the largestvariety of these normally hard to find caps in allpopular sizes. Flexible and easy to work with, R-Caps are used on flat wire or bar stock as dec-orators, lever covers, identifiers. or handle grips.Choose the size, length and bright colour youneed.
FLANGE COVERS
E-Z TAB CAPS
PLUS-PLUGS
Tough, resilient, vinyl ASA flange covers protect critical flange faces and prevent interiordamage and contamination.
These covers fit most American StandardAssociation, Navy and Military sizes and workwith most tubing, including Marman, flared andbeaded. Tough and flexible, FC-series coverscan also be used on joints and flanges. Fit most tubing sizes up to 6-1/2". Both types areavailable in bright yellow.
Tough, flexible vinyl caps with convenientextra-long pull tab makes for easy removal andapplication. Go on snugly and stay put for asuperior seal. Can be used as a paint mask,shipping cap or thread protector.
Used as a cap or plug to keep out moisture orcontamination, patented Plus-Plugs fit most popular threaded and NPT sizes. Flexible non-shredding material assures Plus-Plugs will notpop out during manufacturing or shipping.Patented 360° pull tab assures quick and easyremoval. Most popular sizes shipped from stock.
30Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
CAP GLIDES
Round Cap Glides–Standard
CGC .312CGC .437CGC .500CGC .625CGC .750
CGC .875CGC .937CGC .968CGC 1.000CGC 1.125
CGC 1.250CGC 1.500CGC 1.625CGC 1.750CGC 2.000
5/167/161/25/83/4
7/815/1631/32
11-1/8
1-1/41-1/21-5/81-3/4
2
.413
.610
.643
.661
.646
.653
.578
.655
.655
.669
.578
.625
.578
.570
.563
Part No. Tube OD O/A Height
Round Cap Glides–Heavy Duty
CGC .625HCGC .750HCGC .875HCGC 1.000H
5/83/47/81
1.1121.2401.3681.483
Part No. Tube OD O/A Height
Square Cap Glides
CGS .500CGS .625CGS .750CGS 1.000
1/25/83/41
Part No. Tube OD
Vinyl Cane Tips–Heavy Duty
CANE .625CANE .750
5/83/4
Part No. Tube OD
Standard colour: Black or white.Other sizes and colours available.
Standard colour: Gray.
Standard colour: Black or white.Other sizes and colours available.
Standard colour: Black or white.Other sizes and colours available.
Still looking?
Check page 164 for our silicone and
neoprene products.
31Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
TUBE CAPSShallow, medium and long Tube
Caps fit almost every size of tubingdiameter with a snug friction fit.
Closures are primarily used to capfittings, threaded studs, machined partsand tubes used in packaging drill bitsand other tools.
NIA 210-ANIA 211-BNIA 211-LNIA 212-CNIA 212-S
NIA 213-DNIA 213-RNIA 214-JNIA 214-ENIA 274-G
NIA 215-FNIA 216-HNIA 217NIA 218NIA 219
NIA 219-SNIA 220NIA 981*NIA 220-HNIA 221NIA 221-S
NIA 222NIA 222-HNIA 835NIA 223NIA 201-T†
NIA 201-SNIA 201NIA 748NIA 1202NIA 960
NIA 138NIA 138-2
3/321/81/85/3211/64
3/1613/647/321/49/32
5/163/87/161/29/16
9/165/85/85/8
11/1611/16
3/43/4
13/1613/167/8
7/87/8
29/3229/3263/64
11
5/85/83/4
19/325/8
5/85/83/47/83/4
7/87/87/87/87/8
5/87/87/8
15/167/83/4
7/815/1611/167/85/8
5/87/83/47/81
3/41
25,00030,00025,00025,00010,000
15,00015,00010,000
9,00010,000
7,50010,000
7,5007,0005,000
7,5005,0005,0005,0003,5005,000
3,5002,5003,5002,5002,500
3,5002,5002,5002,5001,500
2,5001,500
Tube Caps
Part No.To Fit
OD LStd.Pkg.
NIA 448NIA 224NIA 289NIA 1783NIA 760
NIA 225NIA 290NIA 291NIA 291-2NIA 1008††
NIA 1008-1NIA 1699NIA 226NIA 327NIA 230
NIA 1365NIA 227NIA 372NIA 374NIA 232
NIA 387NIA 373NIA 1528NIA 1563NIA 1521
NIA 2215NIA 1540NIA 377NIA 1400NIA 1363NIA 324-3
1-1/161-1/81-1/41-5/161-3/8
1-3/81-1/21-5/8
1-23/321-3/4
1-3/41-7/8
22-1/82-1/4
2-1/42-1/2
2-19/322-5/82-3/4
33-1/83-1/43-7/163-1/2
3-33/644
4-1/84-13/164-55/64
8
17/811
5/8
1111
7/8
7/811
7/87/8
17/8111
11-3/8
111
21-1/81-1/241/64
12-1/4
2,0001,5001,5001,0001,000
1,0001,0001,000
500500
500500
1,000500500
300500
1,0001,000
250
450500800700600
30050040050035044
Tube Caps (cont’d.)
Part No.To Fit
OD LStd.Pkg.
NIA 213-SNIA 214-SNIA 1805NIA 216-TNIA 773
NIA 1031NIA 218-SNIA 838NIA 222-SNIA 1784
NIA 2003*NIA 1364NIA 289-SNIA 985NIA 1025
3/161/45/163/87/16
7/161/2
23/323/41
11
1-1/41-3/82-1/8
15/321/23/8
15/327/32
1/21/2
15/323/81/2
1/25/81/2
11/321/2
Shallow Tube Caps
30,00015,00018,00020,00015,000
15,0005,0007,5007,5003,500
3,5002,0002,0002,5001,000
Part No.To Fit
OD LStd.Pkg.
NIA 214-LNIA 216-LNIA 1030NIA 217-LNIA 1834NIA 220-U*
NIA 222-LNIA 201-MNIA 138-LNIA 289-MNIA 289-L
NIA 428NIA 428-2NIA 290-LNIA 291-LNIA 291-3NIA 226-L
15/643/8
27/647/165/85/8
3/47/81
1-1/41-1/4
1-3/81-3/81-1/21-5/8
1-27/322
1-1/81-1/81-1/41-1/22-1/21-1/2
2-15/321-3/41-3/41-1/21-3/4
1-1/21-19/32
1-3/41-1/41-7/321-1/2
15,0007,5005,0005,0001,0002,000
4,0001,0001,000
500500
500500500500500250
Long Tube Caps
Part No.To Fit
OD LStd.Pkg.
All parts this page: Minimums on request.Orange Low Density Polyethylene. Mil Spec (MIL-C-5501/9).
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32” per inch.
Heat distortion temperatures are as follows:Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
Long Tube Caps
* 3 internal rings.† .067 wall thickness.†† .085 wall thickness.
*3 internal tear-drop shaped beads.
*3 internal tear-drop shaped beads.
32Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
FLANGE COVERSThese LDPE flange covers seal out dirt and
contamination. Legs insert quickly and easilyinto bolt-hole pattern on flange. Friction fitholds cover tightly. Thick covering protectsmachined flange face from scratches.
Part No. NPT Size Std. Pkg.
NIA FC-150-0500NIA FC-150-0750NIA FC-150-1NIA FC-150-1500
NIA FC-150-2NIA FC-150-250NIA FC-150-3NIA FC-150-4
NIA FC-150-6NIA FC-150-8NIA FC-150-10NIA FC-150-12
1/23/41
1-1/2
22-1/2
34
681012
————
200—
100100
90———
125 lb. & 150 lb.
Part No. NPT Size Std. Pkg .
NIA FC-300-2NIA FC-300-3
23
150100
300, 400 & 600 lb.
Part No. NPT Size Std. Pkg.
NIA FC-300-4NIA FC-300-6
46
80100
300 lb. only
33Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
SNAP-IN PLUGS
NIA 659*NIA 659-1NIA 411NIA 430NIA 430-S
NIA 437NIA 412NIA 438NIA 413NIA 465
NIA 457NIA 414NIA 415NIA 416NIA 417
NIA 419NIA 472NIA 421NIA 424NIA 425*NIA 425-S*
3/83/81/25/85/8
11/163/47/81
1-3/32
1-3/161-1/41-1/21-3/4
2
2-1/22-5/8
33-3/4
44
3/43/47/8
1-1/1613/16
1-1/161
1-5/321-7/161-5/16
1-9/161-5/81-7/82-1/82-7/16
33-1/83-3/8
44-1/24-1/2
.410
.410
.540
.675
.675
.710
.790
.9101.0701.150
1.2401.2901.5401.7902.080
2.5802.6753.0603.7804.1004.100
.375
.375
.500
.615
.625
.680
.750
.8751.0101.090
1.2001.2501.5001.7502.020
2.5202.6453.0003.7504.0204.020
.310
.305
.400
.500
.545
.556
.625
.750
.8751.000
1.0501.1251.4001.6201.875
2.3752.5202.8503.6503.9003.900
.090
.090
.110
.090
.140
.094
.100
.100
.110
.125
.100
.110
.110
.105
.100
.100
.100
.110
.125
.150
.090
.060
.125
.090
.100
.080
.094
.090
.090
.094
.080
.100
.090
.090
.094
.094
.094
.094
.090
.075
.080
.340
5,0005,000
15,00010,00015,000
8,00010,000
7,0005,0005,000
3,5002,5002,0001,5001,500
1,0001,000
500500250400
FitsHoleSize A B C D E F
Std.Pkg.Part No.
Type 1 (Flush - fits 14-26 gauge material)
FitsHoleSize A B C D E F
Std.Pkg.Part No.
Type 2 (Recessed)
NIA 411-2NIA 412-2NIA 438-2NIA 413-2NIA 465-2NIA 414-2
NIA 415-2NIA 418-2NIA 416-2NIA 417-2NIA 419-2NIA 421-2
1/23/47/81
1-3/321-1/4
1-1/21-5/81-3/4
22-1/2
3
7/81-5/321-1/41-3/81-7/161-5/8
1-7/82
2-1/82-3/8
33-1/2
.538
.800
.9151.0501.1251.308
1.5501.6751.8002.0502.5703.060
.500
.750
.8751.0001.0901.250
1.5001.6251.7502.0002.5003.000
.430
.660
.795
.9301.0001.170
1.4201.5401.6701.9102.4002.910
.125
.170
.155
.160
.160
.140
.150
.160
.160
.180
.160
.190
.285
.360
.350
.350
.350
.350
.370
.350
.350
.360
.380
.410
15,0008,0005,0005,0004,0002,500
2,0001,5001,5001,0001,000
500
Type 1 : Flush front. Type 2 : Recessed front.
Snap-In Plugs are tough, flexible “finishing” plugs used extensively in allsheet metal work to seal access holes.Insertion is a snap. Thanks to an inter-nal bead, they hold on tight when the handling gets tough.
Snap-In Plugs are used by auto rustproofers, on refrigeration units,water heaters, steel doors, paint cans,lawn mowers–even piggy banks!
These can be hot stamped with yourlogo to provide a unique and attractivesolution for product identification. Callus for a quote on hot stamping.
Minimums available on request. Black Low Density Polyethylene
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32” per inch.
Heat distortion temperatures are as follows:Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
Flush Front
34Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
HOLE PLUGS
Close unneeded chassis holes. Moulded of blacknylon, these feature a convex, matte finish head thattapers to a thin edge. Gives your product an uninter-rupted, completed surface you can even paint over.No tools required. Just a quick push locks these firmly into chassis up to 1/4" thick.
Heyco has hole plugs for all occasions and in virtually every size you'll ever need. Plug unwantedholes, provide ventilation, allow viewing access, sealagainst liquids–these are just some of the things youcan do with our hole plugs.
For further information about hole plugs and otherHeyco products, ask for the most current Heyco catalogue.
DP187DP250DP312DP375DP437
DP500DP562DP625DP687DP750
DP812DP875DP1000DP1093DP1187
DP1250DP1375DP1500DP1750DP2000
DP2.093DP2.25DP2.5DP3.0DP3.375DP3.5DP4.0
.187
.250
.312
.375
.437
.500
.562
.625
.687
.750
.812
.8751.0001.093*1.187
1.2501.3751.5001.7502.000
2.093**2.2502.5003.0003.3753.5004.000
1/161/161/161/161/16
1/161/161/161/161/16
1/161/161/161/161/16
1/161/161/161/165/64
7/647/647/647/647/647/647/64
1/45/163/8
15/3217/32
37/6421/3223/3225/3259/64
57/641-1/64
1-13/641-7/321-5/16
1-3/81-1/2
1-43/641-29/322-9/64
2-1/42-27/642-23/323-11/643-21/323-21/324-5/32
15/645/165/1613/3213/32
13/3213/3213/3213/3213/32
13/3229/6429/6429/6429/64
29/6429/6429/6429/6415/32
3/43/43/43/43/43/43/4
.062
.062
.062
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.125
.250
.250
.250
.250
.250
.250
.250
1,0001,0001,0001,0001,000
1,0001,0001,0001,0001,000
1,0001,000
500500500
500500500300300
200200100100100100
50
Part No.Mounting
Hole Diameter
AHead
Thickness
BHead
Diameter
COverallHeight
MaximumChassis
Thickness
MinimumOrderQty.
Standard colour: Black.Other colours available at premium charge if quantities are sufficient.
* can be used up to 1.125 diameter** can be used up to 2.125 diameter
DOME PLUGS
35Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
HOLE PLUGS CONTINUED
SHORTY PLUGS
Use when space inside the panel is aproblem. Shorty plugs have a limited(1/8”) protrusion inside the panel. Theyhave a matte finish head tapering to athin edge for a smooth finished look.Quickly and easily installed.
Part No.Mounting
Hole Diameter
AHead
Thickness
BHead
Diameter
COverallHeight
MaximumChassis
Thickness
SP218SP281SP312SP343SP375
SP406SP437SP468SP500SP531
SP593SP625SP750SP781SP875
.218
.281
.312
.343
.375
.406
.437
.468
.500
.531
.593
.625
.750
.781
.875
1/161/161/161/161/16
1/161/161/161/161/16
1/161/161/161/161/16
9/3211/323/8
13/3215/32
15/3217/3217/3237/6419/32
11/1623/3227/3257/6431/32
1/41/41/41/41/4
1/41/41/41/41/4
1/41/41/41/41/4
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
Minimum order 1000.Standard colour: Black.Other colours available at premium charge if quantities are sufficient.
THICKNESS
A
C
MAXIMUM CHASSIS
36Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
HOLE PLUGS CONTINUED
PRY OUT PLUGS INSULATION PLUGS
ALSO AVAILABLE:
Just like a dome plug, but with holesthat permit air ventilation and heat dissipation. It leaves you with an attractive cover for unsightly or rough-edged chassis holes. Twenty sizes foruse in 1/2" to 4" diameter holes. Quickand easy installation with only fingertippressure.
VENT PLUGS
PAPER TUBE PLUGSThe 1” to 6” polyethylene paper tube
plugs come with convenient fingerpulltabs (one or two, depending on size),and are 1/2" deep. Standard colour isnatural white. Other colours available(minimum order 10,000).
The 8" to 12" diameters only come inblack high density polyethylene. Theyhave a wide flange for easy removalfrom tubes, and are 1-1/4" deep.
TP 1000TP 1250TP 1375TP 1500
TP 1750TP 2000TP 2250TP 2500
11-1/41-3/81-1/2
1-3/42
2-1/42-1/2
Part No. Fits Tube ID Part No. Fits Tube ID
TP 2750TP 3000TP 3500TP 4000
TP 5000TP 6000TP 8000TP 10000TP 12000
2-3/43
3-1/24
5681012
37Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
HOLE PLUGS CONTINUED
Got a strain relief hole where it shouldn'tbe? Don't start again; just fill it with a double"D" plug. These work for other chorded or"DD" holes as well (holes punched or mouldedwith two opposing flats). The convex, mattefinish head tapers to a thin edge, giving yourchassis a completed look. All sizes have ahead thickness of 1/16", and fit a maximumchassis thickness of .125.
.437
.500
.562
.625
.750
.875
.390
.445
.530
.550
.625
.770
17/3237/6421/3223/3259/641-1/64
13/3213/3213/3213/3213/3229/64
DD437-390DD500-445DD562-530DD625-550DD750-625DD875-770
Part No.Mounting
Hole Diameter
DTo PreventRotation
BHead
Diameter
COverallHeight
Minimum order 1000.
DOUBLE “D” PLUGS
38Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
UNIVERSAL PLUG GLIDESFLAT HEAD — 14-23 gauge
UC 1/2UC 5/8UC 3/4UC 7/8UC 1UC 1X*
1/25/83/47/811
*10-14 gauge.
SQUARE
UT 3/4UT 7/8UT 1UT 1X*UT 1-1/4
3/47/811
1-1/4*10-14 gauge.
BALL HEAD
UB 3/4UB 7/8UB 31/32UB 1
3/47/8
31/321
UP 1 X 2UP 1-1/2 X 3UP 2 X 3-1/2
1 X 21-1/2 X 32 X 3-1/2
Part No. Tube OD
RECTANGULAR
UC 1-1/8UC 1-1/4UC 1-1/2UC 1-3/4UC 2
1-1/81-1/41-1/21-3/4
2
UB 1-1/4UB 1-1/2UB 1-3/4
1-1/41-1/21-3/4
UT 1-1/2UT 2UT 2X*UT 2-1/2
1-1/222
2-1/2
Part No. Tube OD Part No. Tube OD
Part No. Tube OD Part No. Tube OD
Part No. Tube OD Part No. Tube OD
39Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
PLUG GLIDES
Plug glides are made of polyethylene.Also available in ABS by special request.
As with most parts we offer, we can alsohave glides designed to your customspecifications.
PGC .625PGC .750PGC .875PGC 1.000PGC 1.125PGC 1.250PGC 1.375
5/83/47/81
1-1/81-1/41-3/8
16-1816-1816-1816-1816-1816-18
16
Part No. Size Gauge
Round Plug Glides
Square Plug Glides
PGC 1.500PGC 1.750PGC 1.875PGC 2.000PGC 2.250PGC 2.500
1-1/21-3/41-7/8
22-1/42-1/2
16-1816-18
1816-18
1616
Part No. Size Gauge
PGA .750PGA .875
3/47/8
16-1816-18
Part No. Size Gauge
Angled Square Plug Glides
PGS .625PGS .750PGS .875PGS 1.000
PGS 1.250PGS 1.500PGS 2.000
5/83/47/81
1-1/41-1/2
2
1816-1816-1816-18
16-1816-1816-18
Part No. Size Gauge
Rectangular Plug Glides
PGR .500X1PGR .500X1.5PGR .750X1.5PGR 1.000X2
1/2 X 11/2 X 1-1/23/4 X 1-1/2
1 X 2
16-1816-1816-1816-18
Part No. Size Gauge
Ask about our Ball Glides and Oval Glides.
Standard Colour: Black. Also available: White.Other sizes and gauges available for all styles.Other styles also available.
40Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
THREADED PIPE PLUGS
NIA TP-1F*NIA TP-3FNIA TP-5FNIA TP-7FNIA TP-9F
1/8-271/4-183/8-181/2-143/4-14
7/167/167/169/165/8
3/161/41/41/41/4
9/3211/3213/3213/3217/32
3/323/323/323/321/8
9/1611/1613/16
11-1/4
7,5004,0002,5001,5002,000
Part No.N.P.TSize A B C D E
Std.Pkg.
NIA TH-3NIA TH-5NIA TH-7NIA TH-9NIA TH-11
1/4-183/8-181/2-143/4-14
1-11–1/2
1/45/163/89/165/8
5/163/83/81/2
17/32
1/29/169/165/83/4
3,5004,0002,5001,500
800
Part No.N.P.T.Size A B C
Std.Pkg.
TH Series Hexagonal Socket
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32” per inch.
Heat distortion temperatures are as follows:Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
*Across Flats-Hexagonal Head Style.
Minimums available on request.Mil Spec (MIL-C-5501/5R)
NIA TP-1NIA TP-3NIA TP-5NIA TP-7
NIA TP-9NIA TP-11NIA TP-13NIA TP-15
Part No .
TP Series Square Head
TP Series Flanged
Black–oil and heat (250°F) resistant High Density Polyethylene.
1/41/41/41/4
1/41/43/83/8
5/163/87/161/2
9/165/87/87/8
1/161/161/161/16
3/323/321/81/8
5,0005,0003,0001,500
2,0001,500
500500
1/8-271/4-183/8-181/2-14
3/4-141–11-1/2
1-1/4–11-1/21-1/2–11-1/2
N.P.TSize A B C D
Std.Pkg.
9/323/87/169/16
5/813/16
11-1/4
TP Series Square HeadHollow threaded plug prevents
damage to tapped holes and provideslow-cost protection (less than metal)during low pressure testing, shipping orin-plant handling. Durable plug is easily tightened with fingers or wrench.
TP Series Flanged Square HeadHollow threaded plug locks into
position for an extra-tight seal due toflanged sealing surface and cannot beforced through opening. Plug will with-stand testing at a higher pressure than standard threaded plug and offers low-cost protection against damage of tapped holes.
TH Series Hexagonal SocketA solid threaded plug offering
exceptional strength as a temporary orpermanent closure. Hex socket receivesstandard Allen wrench sizes for easytightening.
41Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
PIPE THREAD PROTECTORS
Both open end and closed end protectors are made to completelycover the threads of conduit pipe.
Smooth sided caps are designed towork well with automatic vibrating feeders; they use an internal bead to hold on tight when the handling getsrough.
Major producers of iron, steel andaluminum pipe and tubing use theseunique protectors for safer, damage-free shipments.
NIA OE-311NIA OE-312NIA OE-313NIA OE-314NIA OE-315
NIA OE-316NIA OE-317NIA OE-318NIA OE-319NIA OE-320
NIA OE-321NIA OE-322
1/23/41
1-1/41-1/2
22-1/2
33-1/2
4
56
.7911.0001.2541.5971.836
2.3092.7773.3983.8954.392
5.4486.504
.8401.0501.3151.6601.900
2.3752.8753.5004.0004.500
5.5636.625
.78
.78
.971.001.00
1.031.561.631.661.72
1.811.94
BlackRedBlueRed
Black
BlueBlackBlueBlackBlue
BlueBlue
5,0003,5004,0002,5002,000
1,200700400300224
11778
N.P.T.Size
SmallDiameter
LargeDiameter Length Colour
Std.Pkg.Part No.
Minimums available on request.
Minimums available on request.Please call for sizes larger than 12”.
Open End Pipe Thread Protectors
NIA CE-309NIA CE-310NIA CE-311NIA CE-312NIA CE-313
NIA CE-314NIA CE-315NIA CE-316NIA CE-317NIA CE-318
NIA CE-319NIA CE-320NIA CE-321NIA CE-322NIA CE-324
NIA CE-325NIA CE-326NIA CE 327
1/43/81/23/41
1-1/41-1/2
22-1/2
3
3-1/24568
101214
.503
.638
.7911.0001.254
1.5971.8362.3092.7773.398
3.8954.3925.4486.5048.491
10.60312.59013.835
.540
.675
.8401.0501.315
1.6601.9002.3752.8753.500
4.0004.5005.5636.6258.625
10.75012.75014.000
.59
.59
.78
.78
.97
1.001.001.031.561.63
1.661.721.811.942.13
2.342.532.66
OrangeOrangeBlackRedBlue
RedBlackBlueBlackBlue
BlackBlueBlueBlueBlue
BlueBlueBlack
7,0004,0005,0004,0004,500
2,5002,0001,200
700400
3002241177880
403020
N.P.T.Size
SmallDiameter
LargeDiameter Length Colour
Std.Pkg.Part No.
Closed End Pipe Thread Protectors
Colour Coded Low Density Polyethylene
Colour Coded Low Density Polyethylene
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32” per inch.
Heat distortion temperatures are as follows:Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
42Cords Canada Ltd., 62 Densley Avenue, Toronto, Ont. M6M 5E1
Toronto Calling Area: (416) 242-6811 Outside Toronto Area: 1-800-363-5080Fax: (416) 242-6819
STANDARD THREADED CAPSRibbed, threaded cap provides
durable protection for male threadson standard threaded studs and fittings.
Because of its excellent seal, theTC Series is a popular mask forpainting and plating.
NIA TC-1NIA TC-2NIA TC-3NIA TC-40NIA TC-4
NIA TC-42NIA TC-5NIA TC-6NIA TC-60NIA TC-62
NIA TC-63NIA TC-7NIA TC-8-SNIA TC-8NIA TC-8-R*
NIA TC-82NIA TC-9†
NIA TC-10NIA TC-111NIA TC-100
NIA TC-12NIA TC-120NIA TC-13NIA TC-14NIA TC-15
NIA TC-16NIA TC-17†
NIA TC-18NIA TC-19NIA TC-20NIA TC-21
3/8-247/16-207/16-241/2-201/2-20
1/2-209/16-185/8-185/8-205/8-18
5/8-185/8-243/4-163/4-163/4-16
3/4-183/4-207/8-147/8-187/8-20
1-141-20
1-1/16–121-1/16–141-1/8–18
1-3/16–121-1/4–18
1-5/16–121-3/8–181-5/8–121-7/8–12
3/161/41/45/165/16
5/163/83/8
3/8
3/8
1/21/21/2
5/85/85/8
3/43/4
7/8
11
1-1/41-1/2
7/161/21/29/169/16
9/165/8
11/1611/1611/16
11/1611/1613/1613/1613/16
13/1613/1615/1615/1615/16
1-1/161-1/161-5/321-5/321-7/32
1-9/321-3/8
1-7/161-1/2
1-11/161-15/16
7/1615/325/165/161/2
7/81/2
15/325/8
19/32
3/43/81/29/165/8
11/161/2
23/3225/3223/32
25/3225/3213/1613/1615/32
15/1615/327/8
15/3229/32
1
66666
66666
66666
66666
88888
888888
15,00015,00010,000
5,00010,000
5,0007,5007,5005,0005,000
5,00010,000
5,0005,0004,500
5,0005,0005,0005,0004,000
2,0002,0002,0001,5002,500
1,0002,0001,0001,500
500700
Tolerances on all decimal dimensions are ± .010 per inch (example: 2.500 ± .010 per inch = .025).Tolerances for fractional dimensions are ± 1/32" per inch.
Heat distortion temperatures are as follows: Low Density Polyethylene: 100-121°F (66 P.S.I.)
Medium Density Polyethylene: 120-165°F (66 P.S.I.)High Density Polyethylene: 140-180°F (66 P.S.I.)
Part No.
UnifiedThread
Size
TubingSizeOD
OutsideDia.
InsideLength
No.of
RibsStd.Pkg.
Orange Low Density Polyethylene. * Red High Density Polyethylene.† Red Low Density Polyethylene.
Minimums available on request.Mil Spec MIL-C-5501/11 & NAS 814.
TC Series