Post on 05-Apr-2018
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 1/7
Canoeing Department: A Tandem Paddler
by E.T. Keyser
from The Amateur Sportsman and Sportsman's Magazine / early
1900s
Editor's Note:
A long while back I copied the Canoeing column from some early-1900sissues of this magazine without writing on the copies specifically what thedates were. Judging from the dates elsewhere in parts of the column notworth reproducing this dates from late 1901 or early 1902.
The article includes an exceedingly clever way of adding a mast to anotherwise difficult canoe, and for old-time canoe gear geeks we havedrawings of fittings.
Following this simple scheme anyone can add a small downwind sail to acanoe.
View of Sheets and Halyards.
PART I.
THE RIG.
The "Frolic" was built way down in the Pine Tree State by Morris, of
Veazie, and is an open tandem paddler of Indian model and canvas and
cedar construction, thirty-two inches wide at gunwales and seventeen feet
FirstName LastName Search
Search billions of records on Ancestry.com
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 2/7
long, and her owner's only regret in regard to her is that he did not know
enough to have her built one foot longer, as she would have been just as
easy to handle and contained even more storage room.
She has decks about ten inches long at bow and stern, and is fitted with two
cane bottom seats and three thwarts, any one of which may be removed at
will without injury. The bow thwart, indeed, is held in place with thumb
nut to facilitate its removal when desired to accommodate large bits of
duffle. The cane bottom seats are more comfortable than those made of
slats, and don't hold rain and spray on their surface as do those cushioned
with hair and covered with pantasote.
She is fitted with a removable floor of slats 10-1/2 inches wide, and running
from under the after seat to well up in the bow, and she has an outside keel
of oak to take up wear when beaching and hauling up on the float. The rear
seat is 22 inches from the stern, and the forward one 46 inches from the
bow, this arrangement causes her to trim down by the stern when two are
paddling from them.
The thwarts are placed sufficiently distant from each other to allow of
sitting on the floor without putting one's limbs beneath them. The floor is
almost flat for four feet each way from the center, and she tumbles home so
much that she is really three inches wider at water line than at gunwales.
She has considerable sheer, her depth rising from 11 inches amidship to 19
inches at bow and stern.
Her size and the arrangement of the seats allow the crew to paddle either
from them or from cushions on the floor, although in a boat of such great
beam best results are obtained from the former position; in fact were it not
for the tumble home of her sides, it would be impossible to handle the
paddles comfortably from the floor. On 4 inches draught she will easily
carry 650 pounds and paddle much more easily than a craft of the same
dimensions with more dead rise; there is, of course, a corresponding
disadvantage, and this is that she has very little hold on the water and will
slide badly in a beam wind.
Lee boards are a nuisance, and as without them she could not be sailed,
except with the wind directly astern, she is rigged with one of Rushton's
square sails of 25 square feet area; this does not sound very large for a
17-foot canoe, but when it is considered that a sail of this form measures3-1/2 feet in width at top, 5-1/2 at foot, has 5-1/2 ft hoist, and the lower
yard is 19 inches above her floor and that every inch draws in sailing ahead
of the wind, it will be understood that it is all that would be comfortable to
handle in a fresh breeze.
Her spars, three in number, are of clear-grained pine, and were gotten out at
a turning mill at a cost of two dollars for material and labor. The writer got
out just one set of spars, early in his canoeing experience, and lets the mill
do that part of the work now. Such work is conducive to profanity, and
what profits it a man that he save $1.50, but lose most of the cuticle from
his hands and a large slice of his salvation? The mast was turned 1-3/4
inches in diameter at butt, and cylindrical for 19 inches, from thence
tapering to 1-1/4 inches at head.
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 3/7
The lower yard was 6 feet in length, 1-1/4 inches at center, tapering to 1
inch at ends. The upper yard was of the same center diameter, also tapering
to 1 inch at ends, but only 4 feet long; there was thus left 3 inches clear of
spar at each end projecting beyond the sail. Three inches from masthead a
mortise, 2 inches in length by 3/8-inch in width, was cut, and in this was set
a galvanized iron sheave 1/4-inch thick and 1 inch in diameter. This sheave
was knocked out of a galvanized iron block made to take a 1/4-inch rope.
The axis hole of the sheave was enlarged with a rat-tail file to take an1/8-inch brass rod for an axle, and the sheave set with its top edge 3/8-inch
distant from the top of the mortise.
Spruce could have been used in place of pine in the spars, and the mast
been 1-1/2 inches diameter at base, but, although 1-1/2-inch mast plates
may be had, no mast fittings of smaller diameter than 1-3/4 inches are to be
procured, so the lighter wood and greater size had to be used. Right here I
want to make a humble suggestion to two of the best-known canoe builders
of the country, Messrs. Rushton and Morris; if the former would cast his
foot gear rings a trifle smaller and then bore them up true to gauge, and the
latter would fit his Indian model canoes with decks ten inches longer andwithout the sharp bevel on the under side, we amateur riggers would have
an easier time of it.
The collar to take the spar clamp was so much smaller than its nominal size
that the mast had to be worked down to allow it to revolve, although the
collar for the foot-hoisting gear fitted all right, while the very short deck
with its great curve prevented a hole being bored in it for a mast plate, and it
was cut away at so much of an angle that a block could not be fastened
underneath it to receive a screw mast-ring. A deck ten inches longer would
not occupy any valuable space, but would strike a place where the shear was gradual enough to allow boring for stepping, provided the bow end was
simply rounded instead of being cut in a V, and, if flat underneath, would
allow securing to it a block to take one of Phelps' mast screw rings that can
be removed when not in use.
This stepping of the mast was a problem that took considerable time to
solve. It was finally mastered In the following way:
Into the under side of the deck, as close as possible to the bow, a
screw eye was set. Attached to this by a rope was a wooden
deadeye, and through the deadeye a 1/4-inch rope was rove.
One end of this rope was made into a permanent loop, the butt
of the mast was passed through this, the foot of the mast, placed
in the step and the free end of the rope hauled taut; this pulled
the mast firmly against the deck, where the V-shaped notch kept
it from side play, and the free end of the rope was belayed to a
Butler cleat on the port gunwale 2 feet from the bow, the strain
on the mast being all from aft and pressing it against the deck
where it has the greatest possible length of bracing between step
and support; the arrangement worked all right.
In setting the screw eye under the deck it was necessary that it be
far enough forward to allow a couple of inches between the
whipped and of loop and the deadeye, so that all slack could be
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 4/7
taken up. A leather collar was nailed to mast to prevent grinding
and marring of edge of deck, the collar being 2 inches wide, so
that the fastening tacks would be above and below points where
it touched the deck's edge.
Mast Stepping.
The sail is lashed with seizing cord, which passes around the spars and
through each grommet on the sail in half hitches.
To prevent the sail drawing toward the center of the spar, and becoming
slack, a small brass screw eye is screwed 2-1/2 inches from the end of each
yard, and through each of these the outside half hitches on each end of the
yard is run.
Rigging details.
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 5/7
The foot gear consisted of three of Rushton's mast collars, holding in place
his mast foot gear fitted with block and ring, and his spar fastener No.16,
which allows the lower yard to rise and fall with the pressure of the wind,
and also to revolve on the mast. A pin coupling allows its removal from the
mast when stowing the sail.
Rushton's Spar Gear #16.
Pin holds the collar to the mast. Collar can revolve.
Above: Footgear. Block revolves without twisting mast. Reefing lines
or downhauls run through the ring.
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 6/7
Above: Mast Collar, clamped below and above Spar Gear and
Footgear to keep each in position.
A halyard of 1/4-inch rope passes through the block on the foot gear, from
the sheave in the mast head, and was attached to a deadeye fastened in the
center of a piece of 1/8-inch rope, each end of which was securely lashed to
the upper spar about a foot from its ends. This latter rope was so adjustedthat the deadeye at the center was six inches above the spar.
A 3-inch mast ring, which passed over the mast itself, held the spar in
position and the large size of the ring prevented its jamming on the mast
when the sail was raised or lowered. A brass screw eye was inserted at each
end of the lower yard. To these were attached 1/8-inch sheet ropes, which
were belayed to clutch cleats placed on the inside of either gunwale just in
front of the after thwart, where they would be In easy reach.
The use of clutch cleats allowed a quick and easy adjustment of the angle of
the sail, as it was only necessary to pull on one sheet rope, at the same time
releasing the clutch of the other cleat. With a sail 5-1/2 feet wide at its
lower extremity placed in a part of the boat where there was scarcely more
than eight inches of beam, some arrangement was necessary to keep the sail
from hanging in the water when down.
Lazyjacks could have been arranged from the mast head of the lower yard,
but this would have complicated the removing of the sail from the mast.
Instead of this four 1/4-inch brass rings were sewed on each side of the sail
within a foot of its outer edge and also down the center. Through these ran
three pieces of seizing cord lashed to the upper yard and passing through
three deadeyes lashed to the lower one. They were joined at the center and
passed through the ring on the foot gear. On loosing the halyard, a cord
attached to these downhauls was pulled, not only facilitating the lowering
the sail, but bunching it so that it presented a small and compact bundle
when furled. In stowing the sail, the halyard, which fastened to the deadeye,connected with the' top yard by a bow knot, was simply released, the mast
ring pulled over the top of the mast and the pin in the foot gear removed.
The sail could then either be rolled up on the yards the same as a shade, or
bunched, by pulling on the reefing gear, and the mast itself was not too long
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...
7 1/23/2010 12:51 PM
8/2/2019 Canoe Sailing Resources_ CA.
http://slidepdf.com/reader/full/canoe-sailing-resources-ca 7/7
to be easily carried in a boat when not in use The sail appears to contain
much more than its actual area, and decorated as it is, with a huge red
Hippocampus, the totem of the Knickerbocker Canoe Club, the canoe from
dead ahead presents very much the appearance of an old Norse war galley.
Looking at the Bow.
Census Records | Vital Records | Family Trees & Communities | Immigration Records | Military RecordsDirectories & Member Lists | Family & Local Histories | Newspapers & Periodicals | Court, Land & Probate | Finding Aids
oe Sailing Resources: Canoe Square Sail http://freepages.genealogy.rootsweb.ancestry.com/~fassitt/canoe_mirror...