Cable Guide for Mitsubishi HMI Range

Issued by: Mitsubishi Electric Europe B.V. - UK BranchDocument issue: Ver C, June 2000Produced by : - HMI Product MarketingTravellers Lane, Hatfield, Herts, AL10 8XB, UKAuthor: Åsa Nilsson

Databank - Technical Bulletin

Title: Cable guide for Mitsubishi HMI range Page 1 of 27Keywords: Cable guide

Human Machine Interface (HMI)Operator TerminalE Series HMI’sMAC Series HMI’sFX-DU Series HMI’sGOT Series HMI’s

Cable guide for Mitsubishi HMI range

This guide has been created to aid the identification and correct matching of communicationcables, HMIs and PLCs.

Contents

Programming FX 25/30/40/50 DU ............................................................................................. 3Programming F900GOT Series HMIs ....................................................................................... 4Programming A870GOT............................................................................................................ 5Programming MAC 10/12 .......................................................................................................... 6Programming MAC 40+ ............................................................................................................. 7Programming E Series HMIs, MAC 10CM/50/50CM/90 and CM 10 ........................................ 8FX-10DU to PLC........................................................................................................................ 9FX-20DU to PLC...................................................................................................................... 10FX-25DU to PLC...................................................................................................................... 11FX-30/40/50DU and F900GOT Series HMIs to PLC ............................................................... 12MAC 10/12 to PLC................................................................................................................... 14E Series HMIs, MAC 10CM/40+ and CM 10 to PLC................................................................ 15MAC 50/50CM/90 to PLC ........................................................................................................ 17A870GOT to PLC..................................................................................................................... 19E-Series HMIs to GE Fanuc .................................................................................................... 21E-Series HMIs to Omron.......................................................................................................... 22E-Series HMIs to SIMATIC S5................................................................................................. 23E-Series HMIs to SIMATIC S7................................................................................................. 24E-Series HMIs to Allen Bradley DF1........................................................................................ 25E-Series HMIs to Allen Bradley DH485 ................................................................................... 26E-Series HMIs to FREQROL FR-A/FR-E ................................................................................ 27Part numbers ........................................................................................................................... 28

Programming FX 25/30/40/50 DU

FX50DU

FX40DU

FX30DU

FX25DU

232CAB15-UK

25-pin D-sub female 9-pin D-sub female

232CAB15-UKTransfer cable between PC and FX-25/30/40/50 DU. Length 1.5m

Programming F900GOT Series HMIs

232CAB15-UK +ADAPTER

F930/940GOT

9-pin D-sub female 25-pin D-sub male

232CAB15-UKTransfer cable between PC and FX-25/30/40/50 DU. Length 1.5m

ADAPTER25 to 9 pin adapter.

Programming A870GOT

A870GOT

232CAB15-UK

232CAB15-UKTransfer cable between PC andA870GOT. Length 1.5m

Programming MAC 10/12

MAC 10/12

PERIPHERALPSU

SC-06NMAC10/12 CAB orFX-20P-CAB

25-pin D-sub female 25-pin D-sub femaleMiniDIN 8-pin female

MiniDIN 8-pin male MiniDIN 8-pin male

MiniDIN 8-pin male 25-pin D-sub female

SC-06NProgramming interface required at theprogramming of MAC 10/12. Length 3m.

MAC10/12CABCable between MAC 10/12 and SC-06Nwhen programming of MAC 10/12. Length3m.

FX-20P-CABCable between MAC 10/12 and SC-06Nwhen programming of MAC 10/12. Length3m.

OtherVoltage feed, +5VDC, of the MAC 10/12 is done internally by the SC-06N.

Programming MAC 40+

MAC 40+

PERIPHERALPSU

SC-06NMAC 40+ CAB orFX-20P-CAB

25-pin D-sub female 25-pin D-sub femaleMiniDIN 8-pin female

25-pin D-sub male 25-pin D-sub male

220V connection 5VDCSC-06NProgramming interface required at theprogramming of MAC 40+. Length 3m.

MAC 40+ CABCable between MAC 40+ and SC-06Nwhen programming of MAC 40+. Length3m.

FX-20P-CABCable between MAC 10/12 and SC-06Nwhen programming of MAC 40+. Length3m.

PERIPHERAL PSUPower supply unit.

OtherVoltage feed, +5VDC, of the MAC 40+ is done internally by the SC-06N

Programming E Series HMIs,MAC 10CM/50/50CM/90 and CM 10

MAC-PROG/9-CAB

CM10/MAC10 CM

MAC 50/50CM/90

E50*/100/200/300/

600/700/710/900/910

* Use the 9-25 pin adapter, supplied with the E50, to connect the MAC-PROG/9-CAB.

MAC-PROG/9-CABProgramming cable for MAC 50/50CM/90and E100/200/300/600/700/710/900/910

Other Voltage feed, +5VDC, of the CM10 and MAC10 CM is done by connecting a PLC (FXor A range) to the RS422 port, se page 14.

FX-10DU to PLC

FX-10DU

FX-20P-CAB MITSUBISHI

FX-20P-CAB FX-20P-CADP

FX-20P-CAB0 MITSUBISHI

FX0/FX0S/

FX0N/FX2N

MiniDIN 8-pin male 25-pin D-sub male

25-pin D-sub female MiniDIN 8-pin male

FX-20P-CABCable between FX-10DU and1) FX PLC2) FX0/FX0S/FX0N/FX2N PLCs (together

with adapter cable FX-20P-CADP)

FX-20P-CADPAdapter cable used with FX-20P-CAB toconnect FX-10DU to FX0/FX0S/FX0N/FX2N PLCs

FX-20P-CAB0Cable between FX-10DU and FX0/FX0S/FX0N/FX2N PLCs

FX-20DU to PLC

FX-20DU

FX-20DU-CAB/EN MITSUBISHI

MITSUBISHI

FX0/FX0S/FX0N/FX2N

FX-20DU-CAB/EN FX-20P-CADP

Internal fitting 25-pin D-sub male

FX-20DU-CAB/ENCable between FX-20DU and1) FX PLC2) FX0/FX0S/FX0N/FX2N PLCs (together

with adapter cable FX-20P-CADP)

FX-20P-CADPAdapter cable used with FX-20DU-CAB/EN to connect FX-20DU toFX0/FX0S/FX0N/FX2N PLCs

FX-25DU to PLC

FX-25DU

MITSUBISHI

FX0/FX0S/FX0N/FX2N

FX-40DU-CAB/ENCable between FX-25DU and1) FX PLCs2) FX0/FX0S/FX0N/FX2N (together withadapter cable FX-20P-CADP)

FX-20P-CADPAdapter cable used with FX-40DU-CAB/EN to connect FX-25DU toFX0/FX0S/FX0N/FX2N PLCs

FX-30/40/50DU and F900GOT Series HMIs to PLC

FX-40DU

MITSUBISHI

FX0/FX0S/FX0N/FX2N

FX-30DU

FX-50DU

AnS, A

FX-40DU-CAB/EN

F930/940GOT

FX-50DU-CAB0/EN

FX-40DU-CAB/ENCable between FX-30/40/50DU, F940GOTand1) FX, AnS, A PLCs2) FX0/FX0S/FX0N/FX2N (together with

adapter cable FX-20P-CADP)

FX-20P-CADPAdapter cable used with FX-40DU-CAB/EN to connect FX-30/40/50DU,F940GOT to FX0/FX0S/FX0N/FX2N PLCs

Continued over the page………..

FX-30/40/50DU and F940GOT to PLC ….continued…….

FX-50DU-CAB0/EN

Cable between F940GOT andFX0/FX0S/FX0N/FX2N.

MAC 10/12 to PLC

MAC 10/12

MAC-10/12CAB

MITSUBISHI

FX0/FX0S/

FX0N/FX2N

FX-20P-CADP MAC-40+CAB

FX-20P-CAB

MAC10/12CABCable between MAC 10/12 and FX0/FX0S/FX0N/FX2N PLCs

MAC 40+ CABCable between MAC 10/12 and FX PLC(together with adapter cable FX-20P-CADP)

FX-20P-CABCable between MAC 10/12 and FX PLC

FX-20P-CADPAdapter cable used withMAC 40+CAB to connect MAC 10/12 toFX PLC

E Series HMIs, MAC 10CM/40+ and CM 10 to PLC

MAC 40+CAB MITSUBISHI

AnS, A, Q

MAC 40+CAB

E50/100/200/300/600/700/710/900/910

MAC 40+

MITSUBISHI

FX0/FX0S/FX0N/FX2N

MAC 40+CAB FX-20P-CADP

FX-20P-CAB

CM10/MAC10 CM

E Series HMIs, MAC 10CM/40+ and CM 10 to PLC….continued…….

25-pin D-sub male MiniDIN 8-pin male

MAC 40+CABCable between MAC 40+, E Series and1) FX, AnS, A, Q2) FX0/FX0S/FX0N/FX2N (together with

FX-20P-CABCable between MAC 40+, E Series andFX0/FX0S/FX0N/FX2N

FX-20P-CADPAdapter cable used with MAC 40+CAB toconnect MAC 40+, E Series toFX0/FX0S/FX0N/FX2N PLCs

MAC 50/50CM/90 to PLC

MAC-CAB MITSUBISHI

MITSUBISHI

FX0/FX0S/FX0N/FX2N

AnS, A

MAC-CAB

MAC-CAB FX-20P-CADP

MAC-FX0-CAB

MAC 90

MAC 50/50CM

MAC 50/50CM/90 to PLC…..continued…..

15-pin D-sub male MiniDin 8-pin male

MAC-FX0-CABCable between MAC 50/50CM/90 andFX0/FX0S/FX0N/FX2N

MAC-CABCable between MAC 50/50CM/90 and1) FX, AnS, A2) FX0/FX0S/FX0N/FX2N (together with

FX-20P-CADPAdapter cable used with MAC-CAB toconnect MAC 50/50CM/90 toFX0/FX0S/FX0N/FX2N PLCs

A870GOT to PLC

MITSUBISHI

A, AnS, Q

A870GOT

A1SCxxNB

ACxxR4

Programming port

Bus connection AnS

Bus connection A

A870GOT to PLC…….continued…….

9-pin socket 25-pin D-sub male

15-pin male A870GOT bus connector(AnS)

45-pos male A870GOT bus connector (A)

ACxxR4Cable between A870GOT to FX/Ans/ACPU port.3m - AC30R410m - AC100R430m - AC300R4

A1SCxxNBCable between A870GOT and AnS busconnection.0.45m - A1SC05NB3m - A1SC30NB

ACxxBCable between A870GOT and A busconnection.0.6m - AC06B1.2m - AC12B3m - AC30B

E-Series HMIs to GE Fanuc

CAB4-HMICable between E Series and GE FanucPLC system via the SNPX protocol.

E100/200/300/600

700/710/900/910

GE Fanuc PLCwith SNPX protocol

CAB4-HMI

E-Series HMIs to Omron

9-pin D-sub male 9-pin D-sub female

CAB3-HMICable between E Series and Omron PLCsystem via the Hostlink protocol.

E100/200/300/600

700/710/900/910

Omron PLC withHostlink protocol

CAB3-HMI

E-Series HMIs to SIMATIC S5

CAB5-HMICable between E Series and1) Siemens S5 3964R2) Siemens S7 MPI or 3964R3) Allen Bradley DF1

CAB6-HMICable between E-series and1) Siemens S5 3964R2) Siemens S7 MPI

CAB7-HMICable between E-series and Siemens S5PG1 port

E100/200/300/600

700/710/900/910

Siemens S5PG1/AS511

CAB7-HMI

CAB1-HMI 6ES5 734-1BD20

Siemens S53964R/RK512

CAB6-HMI

Null modem CAB5-HMI

E-Series HMIs to SIMATIC S7

25-pin D-sub male RS485 connection

CAB6-HMICable between E-series and3) Siemens S5 3964R4) Siemens S7 MPI

CAB8-HMIRS485 adapter for E-series.

E100/200/300/600700/710/900/910

Siemens S73964R/RK512

CAB5-HMI

Siemens S7MPI

CAB6-HMI 6ES7 972 0CA10-0XA0

CAB5-HMI 6ES7 972 0CA10-0XA0

Siemens S7PPI

CAB8-HMI See manual

See manual 6ES7 901-3BF00

E-Series HMIs to Allen Bradley DF1

9-pin D-sub female MiniDin 8-pin male

CAB2-HMICable between E-series and Allen BradleyMicrologix.

E100/200/300/600

700/710/900/910

Allen Bradley SLC5001747-KE module

Allen-BradleyMicrologix

CAB2-HMI

CAB5-HMI

E-Series HMIs to Allen Bradley DH485

9-pin D-sub female MiniDin 8-pin male

CAB10-HMICable between E-series and Allen BradleySLC 500 (DH485).

E300/600/700/710900/910

Allen Bradley SLC500CAB10-HMI

Point-to point connection

CAB10-HMI

1747-AIC 1747-AIC

Multidrop connection

CAB10-HMI

1747-AIC 1747-AIC

E-Series HMIs to FREQROL FR-A/FR-E

25-pin D-sub male RJ45 contact

CAB9-HMICable between E-series and FREQROLFR-A/FR-E.

Note: For multidrop configuration and cables please refer to the FR-A/E driver manual.

E100/200/300/600

700/710/900/910

FR-A/FR-E

CAB9-HMI

Part numbers

Part number SAP number232CAB15-UK 83838 (part of FX-DU-WIN-SW-KIT, 76048)ADAPTER Part of FX-DU-WIN-SW-KIT, 76048SC-06N 35162MAC10/12 CAB 76959FX-20P-CAB 30815PERIPHERAL PSU 83268MAC 40+ CAB 76945MAC-PROG/9-CAB 76957FX-20P-CAB0 55917FX-20P-CADP 31870FX-20DU-CAB/EN 63161FX-40DU-CAB/EN 62503FX-50DU-CAB0/EN 70451MAC-CAB 76920AC30R4 3930AC100R4 on requestAC300R4 23850A1SC05NB 24983A1SC30NB 47464AC06B 4094AC12B 4091AC30B 4087CAB1-HMI 124261CAB2-HMI 124262CAB3-HMI 124263CAB4-HMI 124264CAB5-HMI 124265CAB6-HMI 124266CAB7-HMI 124267CAB8-HMI 124268CAB9-HMI 128599CAB10-HMI 129442

Cable Guide for Mitsubishi HMI Range

Documents

Transcript of Cable Guide for Mitsubishi HMI Range

HMI Broschüre 2008 UK · 2018-05-16 · Global partner. Local friend. MITSUBISHI ELECTRIC FACTORY AUTOMATION MITSUBISHI ELECTRIC FACTORY AUTOMATION System and Process Visualisation

Delta PLC/HMI Cable Selection Guide - · PDF fileDelta PLC/HMI Cable Selection Guide Industrial Automation Headquarters Delta Electronics, Inc. Taoyuan Technology

RED PROFIBUS PRACTICAS DE LABORATORIObiblioteca.unitecnologica.edu.co/notas/tesis/0062316.pdf · PLC Siemens CPU 314C 2DP 3.2.3. Panel HMI OP177B 3.2.4. Cable PROFIBUS 3.2.5. Cable

Delta PLC/HMI Cable Selection Guide - megaindustrial.shop · Delta PLC/HMI Cable Selection Guide helps users rapidly get the information about the cables suitable to be applied among

Mitsubishi Electric HMI migration guide• Beijer HMI can connect to a Siemens S7 via a CAB36 cable whereas GOTs require an external MPI adapter. • Multimedia/documents • E1000s

INDUSTRIAL ENGINEER PLC & HMI TRAINING - Scantime 2006br.pdf · INDUSTRIAL ENGINEER PLC & HMI TRAINING ... OMRON & MITSUBISHI PLC TRAINING ... PLC Training is done at your own pace;

HMI Hardware...Five HMI models HMI 4.3”, HMI 7” (Low Cost), HMI 7” (High Performance), HMI 10” & HMI 15” are available. 2.1.1 Technical Specifications Model HMI 4.3” HMI

Mitsubishi Electric HMI migration guide

SIMATIC HMI HMI device

Mitsubishi Electric – GOT1020 presentation, February 2007 /// HMI /// GT1020 /// HMI /// GT1020 /// HMI /// GT1020 /// HMI /// GT1020 /// HMI /// GT1020.

Mitsubishi E1000 Series HMI

Drives Solutions brochure v10 BPX - Farnell• Mitsubishi HMI Solutions from BPX • Mitsubishi Servo Solutions from BPX • Mitsubishi Software Solutions from BPX ... 158463 FR-S540E-0.4K-EC

CC-Link Slave Interface - ER-Soft Cable Wiring Manual, publication CC0208-06 Mitsubishi Cc-Link Specification (Profile), publication BTP-05028-B Mitsubishi Revision Date Author(s)

Datenmanagement für Ihre automatisierte Produktion...SCADA / HMI Feldgeräte / Antriebe / Roboter 3S CODESYS Beckhoﬀ Bosch Rexroth B&R GE Mitsubishi ... Schneider Electric Siemens

About Hytech AutomationSiemens S7 1500 or Mitsubishi Q Series. HMI provided with the kit is again an advance level HMI such as Siemens KTP 900 or Mitsubishi GOT Series. • PH Advance

HMI Broschüre 2008 UK - AI Automationaiautomation.com.au/wp-content/uploads/2013/04/207075.pdf · MITSUBISHI ELECTRIC FACTORY AUTOMATION MITSUBISHI ELECTRIC FACTORY AUTOMATION System

MITSUBISHI ELECTRIC¡tor_terminálok_(HMI)/2.3._E1000/2.3.1...Mitsubishi Electric, MA00815 Installation manual for the E1000 series operator terminals Foreword The E1000 operator terminal

AGL HMI Framework - wiki.automotivelinux.org · HMI-Apps is used after requesting the HMI resource required for HMI-Manager HMI-Apps will do the appropriate processing when the HMI

expert-automation.com MITSUBISHI Graphic... · 2019-09-22 · Tailored solutions to meet your HMI and visualization needs Mitsubishi Graphic Operation Terminal GOT1000 Series Mitsubishi

Mitsubishi Electric - …...For repair, contact your local Mitsubishi Electric representative. • Turn off the power to the PLC before connecting or disconnecting any extension cable.