Post on 08-Nov-2014
QY8-1370-000
REVISION 0
COPYRIGHT 2000 CANON INC. CANON BJC-6200 0400 AB 0.20-0 PRINTED IN JAPAN (IMPRIME AU JAPON)
Apr. 2000
042000 AB 0.20-0
ApplicationThis manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair
of products. This manual covers all localities where the products are sold. For this reason, there may be information in this
manual that does not apply to your locality.
CorrectionsThis manual could include technical inaccuracies or typographical errors due to improvements or changes in the products.
When changes occur in applicable products or in the content of this manual, Canon will release technical information as the
need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new
editions of this manual
The following paragraph does not apply to any countries where such provisions are inconsistent with locallaw.
TrademarksThe product names and company names described in this manual are the registered trademarks of the individual companies.
CopyrightThis manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or
translated into another language, in whole or in part, without the written consent of Canon Inc., except in the case of internal
business use.
Copyright 2000 by Canon Inc.CANON INC.BJ Printer Technical Support Dept. 1116-1, Shimonoge 3-chome, Takatsu-ku, Kawasaki, Kanagawa 213-8512, Japan
This manual has been produced on an Apple Power Macintosh 7300/180 personal computer and OKI MICROLINE 803 PSIIV
laser beam printer; artworks of printing films were printed on Agfa SelectSet Avantra 25. All page layouts, logos, and parts-list
data were saved with Canon Optical Disc Subsystem mo-5001S™ and Optical Disc Cartridge mo-502M™, and Interface Kit
mo-IF2™ for Macintosh. All graphics were produced with MACROMEDIA FREEHAND™ 7.0J. All documents and all page
layouts were created with QuarkXpress™ 3.3 Japanese version.
I
I. ABOUT THIS MANUAL
This manual consists of three parts containing information for servicing the product.
Part 1: Product SpecificationsProduct overview and specifications.
Part 2: TroubleshootingA guide to troubleshooting the product and identifying the parts and units needing replacement.Troubleshooting is described according to problem descriptions as well as error indications by the statusindicator.
Part 3: AppendixBlock diagrams, information on the hardware technologies, and pin configurations.
Disassembly and reassembly procedures are not fully covered in this manual. Refer to theseparate Parts Catalog instead.
Pro
du
ctS
pecificatio
ns
TroubleshootingA
pp
end
ix
II. TABLE OF CONTENTS
Page Part 1: PRODUCT SPECIFICATIONS1 - 1 1. PRODUCT OUTLINE1 - 1 1.1 Product Outline1 - 2 2. SPECIFICATIONS1 - 2 2.1 Printer Specifications1 - 2 2.1.1 Printer specifications1 - 2 2.1.2 Printer service life1 - 3 2.2 Paper Specifications1 - 3 2.2.1 Paper sizes and weights1 - 3 2.2.2 Paper types and handling1 - 4 2.2.3 Printable area1 - 4 2.3 BJ Cartridge Specifications1 - 5 2.4 Optional Scanner Cartridge Specifications1 - 5 2.4.1 Scannable area1 - 6 2.5 Printer and Scanner Drivers1 - 7 3. PACKING CONFIGURATION1 - 8 4. PARTS CODE LIST
Part 2: TROUBLESHOOTING2 - 1 1. PRINTER OPERATION2 - 1 1.1 Status Indicator2 - 1 1.1.1 Status display via the indicator2 - 2 2. SERVICING2 - 2 2.1 Before Troubleshooting2 - 3 2.2 Detectable Problems from System Start to Exit2 - 6 2.3 Troubleshooting Problems2 - 7 2.4 Troubleshooting With Error Indications2 -10 3. DISASSEMBLY AND REASSEMBLY2 -10 3.1 Cautions for Disassembly and Reassembly2 -10 3.1.1 Ink stains (Ink path/ink mist)2 -10 3.1.2 Static electricity damage2 -10 3.1.3 Spur tips deformation2 -10 3.1.4 Feed gear damage2 -10 3.1.5 Tap screw removal and installation2 -11 3.2 Exploded View2 -13 3.3 Disassembly and Reassembly2 -13 3.3.1 Carriage lock release2 -13 3.3.2 Removing and installing tap screws2 -14 3.3.3 Removing the upper cover unit2 -14 3.3.4 Removing the printer unit2 -15 3.3.5 Removing the pressure roller unit2 -15 3.3.6 Spur positions on the spur base unit2 -16 3.3.7 Removing the ASF unit2 -16 3.3.8 Removing the head gap adjustment section2 -17 3.4 Adjustments and Settings After Disassembly and Reassembly2 -17 3.4.1 Adjustments2 -18 3.4.2 Applying grease2 -19 3.4.3 Print head position adjustment2 -20 3.4.4 Setting the EEPROM2 -20 3.4.5 Adjusting the carriage belt tension2 -21 3.4.6 Adjusting the head gap
II
Page2 -23 4. OPERATION CHECK AFTER DISASSEMBLY AND REASSEMBLY2 -23 4.1 Check Procedure2 -24 5. TRANSPORTING THE PRINTER2 -24 5.1 Preparation for Transport2 -25 6. PARTS REPLACEMENT, PERIODIC INSPECTIONS, & TOOLS2 -25 6.1 Parts Replacement2 -25 6.2 Periodic Inspections2 -25 6.3 Tool List2 -26 6.4 Operation with the Printer's Operation Panel2 -26 6.4.1 Cleaning2 -26 6.4.2 Printing the nozzle check pattern2 -27 6.4.3 Roller cleaning2 -28 7. SERVICE-RELATED FEATURES2 -28 7.1 Service Mode Operations2 -29 7.2 Service/Factory Test Printout2 -30 7.3 Printing the EEPROM Information2 -31 7.4 Resetting the EEPROM2 -31 7.5 Setting the Model with the EEPROM2 -31 7.6 Ink Availability Check2 -31 7.7 Auto Print Head Position Adjustment2 -31 7.8 Power Off/Carriage Lock
Part 3: APPENDIX3 - 1 1. TECHNICAL REFERENCE3 - 1 1.1 Print Mode List3 - 2 1.2 Purge Unit's Capping and Cleaning Functions3 - 2 1.3 Cautions About the Inks3 - 3 1.4 Operation with a Computer3 - 3 1.4.1 Setting functions with the printer driver3 - 4 1.5 Detection Functions by Sensors3 - 5 1.6 Electronic Circuit Description3 - 5 1.6.1 Circuit block diagram3 - 5 1.6.2 Power source line block diagram3 - 6 2. CONNECTOR LOCATIONS AND PIN CONFIGURATIONS3 -10 2.1 Carriage Board3 -11 2.2 BJ Cartridge3 -12 2.3 Scanner Cartridge (Optional)3 -13 2.4 AC Adapter3 -13 2.5 DC Power Cable3 -14 2.6 Carriage Motor3 -14 2.7 Paper Feed Motor3 -14 2.8 ASF Motor3 -15 2.9 Ink Sensor3 -15 2.10 Printing Position Sensor3 -15 2.11 Purge Sensor Connector3 -17 2.12 Circuit Diagrams
III
III. ILLUSTRATION INDEX
Page Part 1: PRODUCT SPECIFICATIONS1 - 1 Figure 1 - 1 Printer Appearance1 - 4 Figure 1 - 2 Printable Area1 - 5 Figure 1 - 3 Scannable Area1 - 7 Figure 1 - 4 Packing Configuration
Part 2: TROUBLESHOOTING2 - 1 Figure 2 - 1 Operation Panel2 -11 Figure 2 - 2 Exploded View2 -13 Figure 2 - 3 Carriage Lock Release2 -14 Figure 2 - 4 Upper Cover Unit Removal and Installation2 -14 Figure 2 - 5 Removing the Printer Unit2 -15 Figure 2 - 6 Removing the Pressure Roller Unit2 -15 Figure 2 - 7 Spur Positions on the Spur Base Unit (Bottom View)2 -16 Figure 2 - 8 Removing the ASF Unit2 -16 Figure 2 - 9 Carriage Shaft Position Adjustment Bearing2 -18 Figure 2 -10 Applying Grease2 -19 Figure 2 -11 Print Position Adjustment Pattern2 -20 Figure 2 -12 Carriage Belt Tension Adjustment2 -21 Figure 2 -13 Head Gap Adjustment 12 -22 Figure 2 -14 Head Gap Adjustment 22 -27 Figure 2 -15 Nozzle Check Pattern Printout (Color Sample)2 -29 Figure 2 -16 Service/Factory Test Printout (Sample)2 -30 Figure 2 -17 EEPROM Information Printout (Sample)
Part 3: APPENDIX3 - 3 Figure 3 - 1 Printer Driver Utilities (Sample)3 - 4 Figure 3 - 2 Sensor Locations3 - 5 Figure 3 - 3 Block Diagram3 - 5 Figure 3 - 4 Power Source Line Block Diagram3 - 6 Figure 3 - 5 Control Board3 - 6 Figure 3 - 6 Printer Diagram3 -10 Figure 3 - 7 Carriage Board3 -11 Figure 3 - 8 BJ Cartridge3 -12 Figure 3 - 9 Scanner Cartridge3 -13 Figure 3 -10 AC Adapter3 -13 Figure 3 -11 DC Power Cable3 -14 Figure 3 -12 Carriage Motor3 -14 Figure 3 -13 Paper Feed Motor3 -14 Figure 3 -14 ASF Motor3 -15 Figure 3 -15 Ink Sensor3 -15 Figure 3 -16 Print Position Sensor3 -15 Figure 3 -17 Purge Sensor
IV
IV. TABLE INDEX
Page Part 1: PRODUCT SPECIFICATIONS1 - 8 Table 1 - 1 PARTS CODE LIST
Part 2: TROUBLESHOOTING2 - 7 Table 2 - 1 ERROR INDICATIONS
Part 3: APPENDIX3 - 1 Table 3 - 1 PRINT MODE LIST3 - 2 Table 3 - 2 INK CONSUMPTION DURING CLEANING (GENERAL GUIDE)
V
Part 1PRODUCTSPECIFICATIONS
Page1 - 1 1. PRODUCT OUTLINE1 - 1 1.1 Product Outline1 - 2 2. SPECIFICATIONS1 - 2 2.1 Printer Specifications1 - 3 2.2 Paper Specifications1 - 4 2.3 BJ Cartridge Specifications1 - 5 2.4 Optional Scanner Cartridge Specifications1 - 6 2.5 Printer and Scanner Drivers1 - 7 3. PACKING CONFIGURATION1 - 8 4. PARTS CODE LIST
1. PRODUCT OUTLINE
1.1 Product Outline"Standard Color Printer for Personal Use"
1) Dual cartridge system for high-speed monochrome printing and high-speed color printing.2) Printer cartridge incorporates ink drop modulation technology for high-quality 1440 × 720 dpi printing.3) Separate ink cartridges and tanks for all colors to reduce running costs.4) USB interface enables connection to Windows 98/2000, iMac, and Power Macintosh G3/G4 computers.5) Optional drop-in scanner cartridge.6) Photo cartridge enables six-color, density-matched photo-quality printing.7) Black cartridge contains pigment-colored ink for truer black text printing.8) Highly precision ink-low detection with an optical system and dot count.9) Stabilized image printing with the easy to use automatic print position adjustment.
1-1
BJC-6200 Part 1: Product Specifications
Pro
du
ctS
pecificatio
ns
Operation Panel
Front Cover
Paper Output TrayPaper ThicknessLever
Auto Sheet Feeder
Cartridge Container
BJ Cartridges
Color
Paper SupportPaper Guide
USB Interface PortParallel Interface Port
Black(Optional)
Photo(Optional)
Scanner Cartridge(Optional)
Figure 1-1 Printer Appearance
2. SPECIFICATIONS
2.1 Printer Specifications2.1.1 Printer specifications
2.1.2 Printer service lifeThe printer's service life extends until any of the following conditions is attained:(1) A total of 20,000 sheets are printed with 1,500 character standard in black ink.(2) A total of 6,000 sheets are printed at 7.5% duty per color.(3) Five years of operation elapses.
Part 1: Product Specifications BJC-6200
1-2
TypePaper Feed SystemResolutionThroughput (Referenceonly)
Printing Direction
Max. Printing WidthInterfaceASF Capacity
Sensors
Operating NoiseAmbient Conditions
Power Source
External DimensionsRequired Space
WeightStandard Conformance
Desktop serial printerAutomatic feed only (No manual feed)1440 × 720 dpi (Max. resolution)
* Catalog specification. HS mode (180 × 180 dpi): BidirectionalHQ mode (360 × 360 dpi, 720 × 720 dpi): Unidirectional/BidirectionalFine mode (360 × 360 dpi, 720 × 720 dpi, 1440 × 1440 dpi): Bidirectional203 mmUSB, IEEE 1284-standard, 8-bit parallel (Compatible/Nibble/ECP)Plain paper: Max. 10 mm (Approx. 100 sheets with 64 g/m2)BJ Printer paper: Max. 10 mm (Approx. 80 sheets of high-quality paper)• Front cover-open sensor • Printing position sensor• BJ cartridge sensor • Paper sensor• BJ cartridge ID sensor • Waste-ink capacity sensor• No-ink sensor • Paper width sensor: None• Internal temperature sensorApprox. 45 dB (A) Sound pressure level conforms to ISO 9296.During operation: Temperature 5°C-35°C (41°F-95°F)
Humidity 10%-90% RH (No condensation)During non-operation: Temperature 0°C-35°C (32°F-95°F)
Humidity 5%-95% RH (No condensation)Power voltage/frequency Power consumption During standby100-120 VAC 50/60 Hz Approx. 30 W 3.5 W220-240 VAC 50/60 Hz Approx. 30 W 3.5 WApprox. 455 mm (W) × 312 mm (D) × 173 mm (H)(With retracted paper support and no output tray.)Approx. 455 mm (W) × 562 mm (D) × 248 mm (H)(With output tray and retracted paper support.)Approx. 4.1 kgRadio-wave interference: FCC, IC, CE Mark, Taiwan EMC, C-Tick, VCCIElectrical safety: UL, C-UL, CB Report, GS, CE Mark, FIMKO, SEMCO, IEC, AS, CCIB,
SISIR, Korean Electric Commerce, NEMKOEnvironmental: Energy Star, Blue Angel
BC-30 + BC-31 Cartridge
Black Text (PC Magazine)
New monochrome pattern (J)
New color pattern (J)
BC-32 Photo + BC-31 Cartridge
Full Address Printing
High-speed
9.6 ppm
10 ppm *
7 ppm *
-
High-quality
1.7 ppm
2.0 ppm
1.2 ppm
0.14 ppm *
Standard
7.7 ppm
8.3 ppm *
3.7 ppm *
-
2.2 Paper Specifications2.2.1 Paper sizes and weights
(1) Paper sizesA4, B5, A5, A5 landscape, letter, legal, envelope (C4 and C6), postcard
(2) Weight64 g - 105 g/m2 for auto feeding
2.2.2 Paper types and handling
* Paper dedicated to BJ printers.
If the Paper Thickness Lever is not properly set, problems with paper feeding or printingmay occur.
1-3
BJC-6200 Part 1: Product Specifications
Pro
du
ctS
pecificatio
ns
TypePlain paper
Plain paper forColor BJHigh-qualitypaperPhoto glossypaperGlossy filmTransparencyfilmBack print filmBannerT-shirt transferPhoto glossycardPostcardEnvelope
SizeA4/B5/LTR/LGL/A5 (Portrait/Landscape)A4/LTR
A4/LTR
A4/LTR
A4/LTRA4/LTR
A4/LTR
A4/LTRA4/LTR
120 mm × 216 mm
100 mm × 148 mm241 mm × 105 mm220 mm × 110 mm
-
LC-301*
HR-101*
GP-301*
HG-201*CF-102*
BF-102*
BP-101*TR-201*
FM-101*
COM #10DL-size
ASF CapacityApprox. 10 mm or less(Approx. 100 sheets of 64 gweight)Approx. 10 mm or less
Approx. 10 mm or less
Less than 10 sheets
1 sheetLess than 30 sheets
Less than 10 sheets
1 sheet1 sheet
1 sheet
Less than 40 sheetsLess than 10 sheetsLess than 10 sheets
Paper Thickness Lever PositionUp
Up
Up
Up
UpUp
Up
DownDown
Up
UpDownDown
2.2.3 Printable area
2.3 BJ Cartridge Specifications
* Based on the printable area of A4 paper.
Part 1: Product Specifications BJC-6200
1-4
: Recommended printing area
: Printable area
3.0mm
5.0mm
3.4mm: A4/A5/B56.4mm: LTR/ LGL
3.4mm: A4/A5/B56.3mm: LTR/ LGL
(1) 23mm(2) 26mm
32mm
A4/A5/B5/Letter (LTR)/Legal (LGL)/
3.0mm
5.0mm
6.4mm
Envelope
(1) For monochrome printing.
(2) For color or photo-quality printing.
(COM#10: 31.4mm)(DL size: 10.4mm)
Banner Paper
3.4mm
3.4mm
32mmMax. 6 sheets printable. After printing, the seventh sheet is cut off.
1 2 3 4 5 6
3mm
Figure 1-2 Printable Area
ConstructionHead
Ink colorsTank
WeightService LifePrintableSheets
Black BJ CartridgeBC-30Detachable ink tank160 nozzles (Vertical array)Bk (160 nozzles × 1)Pigment blackBCI-3BK
60 g (w/o ink tank)Approx. 5000 sheetsApprox. 500 sheets/tank(1,500 black characters/page)
Color BJ Cartridge BC-31Detachable ink tank144 nozzles (Vertical array)C, M, Y (48 nozzles × 3)Dye C, M, YBCI-3C, BCI-3M, BCI-3Y
60 g (w/o ink tank)Approx. 3000 sheetsApprox. 280* sheets/tank(7.5% printing per color)
Photo BJ CartridgeBC-32 PhotoDetachable ink tank144 nozzles (Vertical array)Bk, C, M (48 nozzles × 3)Dye PBk, PC, PMBCI-3BK Photo, BCI-3PC Photo, BCI-3PM Photo60 g (w/o ink tank)Approx. 3000 sheetsApprox. 280* sheets/tank(7.5% printing per color)
2.4 Optional Scanner Cartridge Specifications
* Measurement Conditions• Computer: Dell XPS T550 (Pentium III 550 MHz, 256MB RAM)• Interface: Parallel interface, ECP mode• Scanning paper size: A4• The scanning time spans from the start of the carriage scanning operation to the output of the document.
2.4.1 Scannable areaWhen scanning a document, be sure to use the scanning holder to prevent paper jamming. Align the documentwith the scanning baseline when placing it in the scanning holder.
The document sizes and scanning area are listed below.
** The actual scannable area may vary slightly depending on the monitor's display resolution and thescanner's scanning resolution.
** If the B5 Scanning Holder (provided with Scanner Cartridge IS-32) is used to scan a large-sizedocument, the optional A4/LTR Scanning Holder (SH-101) will be required.
1-5
BJC-6200 Part 1: Product Specifications
Pro
du
ctS
pecificatio
ns
DesignationTypeResolution (dpi)Imaging SensorLight SourceScanning System/DirectionDocument FeedingInterfaceExternal DimensionsWeightOther Specifications
Scanning Time (reference)*
IS-32Cartridge replacement type color scanner90 × 90, 180 × 180, 200 × 180, 300 × 360, 360 × 360, 720 × 720256-pixel, linear (single line) CCDRGB (Red, Green, Blue)RGB-switching progressive scanningDocument inserted in scanning holder and fed via the ASFECP/NibbleApprox. 41 mm (W) × 90 mm (D) × 77 mm (H)Approx. 100 gPrinter setting for scanning: Paper thickness lever must be up.Paper sizes for scanning: A4/LTR size or smaller (with BJ F620)Paper thickness for scanning: 0.25 mm or lessApprox. 3 min. 14 sec. (DTP color mode: A4, 180 dpi)Approx. 6 min. 15 sec. (Photo mode: A4, 360 dpi)
6mm
Scanning holder
Scanning baseline
3.4mm
32mm
21mm
Scanning area Recommended scanning area
Document
Figure 1-3 Scannable Area
DocumentPostcardA5B5A4**Letter**
Size (W × H) mm100.0 × 148.0148.0 × 210.0182.0 × 257.0210.0 × 297.0
215.9 × 279.4 (8.5 × 11.0 in.)
Scannable Area* (W × H) mm93.2 × 138.0
141.2 × 200.0175.2 × 247.0203.2 × 287.0208.2 × 269.4
2.5 Printer and Scanner DriversThe drivers and interface ports that can be used with the printer are listed below.
●●: Compatible. ▲▲: Conditionally compatible. ✕: Incompatible.* For USB, compatibility is assured only with personal computers with Windows 98/2000 preinstalled.** Compatible with iMac and Power Macintosh G3. iMac running on Mac OS 8.1 requires iMac updater
1.0.*** Common driver for Windows 95/98/NT 4.0/2000. Operates in Nibble or ECP mode.
1) Window DriversWin 95/98 BJ raster printer driver (IEEE 1284, 8-bit parallel and USB supported)Win NT 4.0 BJ raster printer driverWin 2000 BJ raster printer driverWindows 95/98/NT 4.0/2000 scanner driver IS Scan
2) Macintosh DriversMac BJ printer driver (USB)Mac scanner driver IS Scan (USB)
Part 1: Product Specifications BJC-6200
1-6
Windows 95/98Windows NT4.0Windows 2000Macintosh
Printer Driver Scanner DriverParallel I/F
●●
●●
●●
---
USB I/F▲▲*✕
●●*●●**
Parallel I/F●●***●●***●●***---
USB I/F▲▲*✕
●●*●●**
3. PACKING CONFIGURATION
After opening the package, make sure all the items below have been included.
1-7
BJC-6200 Part 1: Product Specifications
Pro
du
ctS
pecificatio
ns
Quick Start Guide
Ink Tanks
User ManualsCartridge Container
BJ Cartridges
Printer
Power Cord
Output Tray
Packing Materials
Tape
Packing Materials
Packing Materials Tape
Tape
Tape
Figure 1-4 Packing Configuration
4. PARTS CODE LIST
A list of printer parts, consumables, and optional equipment are listed below.
* Items included with BJC-6200: BC-30, BC-31, BCI-3BK, BCI-3C, BCI-3M, BCI-3Y, SB-30.
Part 1: Product Specifications BJC-6200
1-8
Table 1-1 PARTS CODE LIST
ItemPrinter
BJ cartridge
Ink cartridge
Cartridge storage boxScanner cartridgeA4/LTR scanning holder
-
BlackColorPhotoBlackCyanMagentaYellowPhoto blackPhoto cyanPhoto magenta--Scanning holderStandard white sheet
DesignationBJC-6200
BC-30BC-31BC-32 PhotoBCI-1BKBCI-3CBCI-3MBCI-3YBCI-3PBK PhotoBCI-3PC PhotoBCI-3PM PhotoSB-30IS-32SH-101
Product CodeQ30-3310Q30-3312F45-1471F45-1481F45-1501F47-2171F47-2181F47-2191F47-2201F47-2231F47-2211F47-2221Q70-4040Q70-4070Q70-3640
Part 2TROUBLESHOOTING
Page2 - 1 1. PRINTER OPERATION2 - 1 1.1 Status Indicator2 - 2 2. SERVICING2 - 2 2.1 Before Troubleshooting2 - 3 2.2 Detectable Problems from System Start to Exit2 - 6 2.3 Troubleshooting Problems2 - 7 2.4 Troubleshooting With Error Indications2 -10 3. DISASSEMBLY AND REASSEMBLY2 -10 3.1 Cautions for Disassembly and Reassembly2 -11 3.2 Exploded View2 -13 3.3 Disassembly and Reassembly2 -17 3.4 Adjustments and Settings After Disassembly and Reassembly2 -23 4. OPERATION CHECK AFTER DISASSEMBLY AND REASSEMBLY2 -23 4.1 Check Procedure2 -24 5. TRANSPORTING THE PRINTER2 -24 5.1 Preparation for Transport2 -25 6. PARTS REPLACEMENT, PERIODIC INSPECTIONS, & TOOLS2 -25 6.1 Parts Replacement2 -25 6.2 Periodic Inspections2 -25 6.3 Tool List2 -26 6.4 Operation with the Printer's Operation Panel2 -28 7. SERVICE-RELATED FEATURES2 -28 7.1 Service Mode Operations2 -29 7.2 Service/Factory Test Printout2 -30 7.3 Printing the EEPROM Information2 -31 7.4 Resetting the EEPROM2 -31 7.5 Setting the Model with the EEPROM2 -31 7.6 Ink Availability Check2 -31 7.7 Auto Print Head Position Adjustment2 -31 7.8 Power Off/Carriage Lock
1. PRINTER OPERATION
The printer's operation status is indicated by the status indicator, and the printer can be controlled from thecomputer or with the printer itself.
1.1 Status IndicatorThe printer's operation status is indicated by the indicator. When an error occurs, the nature of the error canbe known by the number of times the indicator blinks in orange and/or green.
1.1.1 Status display via the indicatorThe operation status indicated by the indicator is as follows.
2-1
BJC-6200 Part 2: Troubleshooting
Troubleshooting
POWER button
Indicator
RESUME button
Figure 2-1 Operation Panel
IndicatorGreen lightGreen blinking
OFF
Operation StatusPower ONPower ON operation in progress, power OFF operation in progress, resetoperation in progress, cleaning in progress, test printing, front cover open,printing in progress.Power OFF
2. SERVICING
2.1 Before TroubleshootingBefore troubleshooting the printer, check the following and see if any of the applicable problems can befixed.
Part 2: Troubleshooting BJC-6200
2-2
ProblemThe printer does not
operate at all
Paper feeding does not
work
No printing
Stripes appear in the
printing
Probable CauseThe power outlet is not supplying the
required voltage.
The power cord is not properly
connected to the printer or power outlet.
The power switch is not ON.
The recommended paper is not being
used.
There is foreign matter in the paper feed
section (sheet feeder, pinch roller, LF
roller, platen, spurs).
The paper thickness lever is not set
properly.
The print head needs cleaning.
The ink cartridge is empty.
The BJ cartridge has not been used for a
prolonged period.
The recommended paper is not being
used.
The print head is installed in the wrong
position.
The orange tape is still affixed to the
print head.
The print head position adjustment has
not been done.
SolutionConnect the AC cord to a power outlet
that supplies the required voltage.
Check that the power cord is connected
properly.
Turn on the power switch.
Use the recommended paper.
Remove the foreign matter.
Set the lever to the proper setting.
Conduct cleaning.
Replace the ink cartridge.
Conduct cleaning. If the problem still
persists, replace the BJ cartridge.
Use the recommended paper.
Install the print head properly.
Remove the orange tape.
Execute the print head position
adjustment. See page 2-19.
2.2 Detectable Problems from System Start to Exit
2-3
BJC-6200 Part 2: Troubleshooting
Troubleshooting
• No error indication(see page 2-9)
AC power connection AC power supplied
With the POWER button
To nextpage
MPU & printercontroller initialization
ROM check
DRAM check
Ink sensor check/wasteink-full check/internaltemperature sensor
(TH501) check
Ink sensor error
EEPROM read
Power ON
Indicator blinks
Part 2: Troubleshooting BJC-6200
2-4
• Indicator repeats: Blinks once in orange,repeatedly.(See page 2-8)
• Indicator repeats: Blinks 3 times in orange,followed by a long blink in green, repeatedly.(See page 2-7)
Yes
Yes
Yes
Yes
No paper
Paper exists
• Indicator repeats: Blinks 3 times inorange/green, then one long blink in green.(See page 2-8)
• Indicator repeats: Blinks 7 times inorange/green, followed by a long blink ingreen, repeatedly.
• Indicator repeats: Blinks 5 times inorange/green, followed by a long blink ingreen, repeatedly.(See page 2-8)
• Indicator repeats: Blinks 6 times inorange/green, followed by a long blink ingreen, repeatedly.(See page 2-8)
• Indicator repeats: Blinks 2 times inorange, repeatedly.(See page 2-8)
• Indicator repeats: Blinks 8 times inorange/green, followed by a long blink ingreen, repeatedly.(See page 2-9)
• Indicator repeats: Blinks 4 times inorange/green, followed by a long blink ingreen, repeatedly.(See page 2-8)
• Is there paper inside the printer?
* Any ROM/RAM errors are indicated as
described above only during initialization.
Frompreceding
page
Error check
No
Diode sensor check
Abnormal headtemperature error
Diode sensor error
Internal temperaturesensor error
Waste ink-full error
RAM error*
ROM error*
EEPROM error
No
Home position check
Carriage lock release
Paper check
Home position error
NoNormal?
Paper discharge
Paper check
Paper jam error
To nextpage
Normal?
Normal?
NoNormal?
2-5
BJC-6200 Part 2: Troubleshooting
Troubleshooting
• Indicator repeats: Blinks 7 times inorange, followed by a long blink ingreen, repeatedly.(See page 2-7)
• Indicator repeats: Blinks 7 times inorange, followed by a long blink ingreen, repeatedly.(See page 2-7)
• Indicator repeats: Blinks 5 times inorange, followed by a long blink ingreen, repeatedly.(See page 2-7)
• Cartridge installation• Cartridge not recognized• Not installed properly
The sensor will determine if thefront cover is open or closed.
• Indicator repeats: Blinks 10 times inorange/green, followed by a long blink ingreen, repeatedly.(See page 2-9)
Frompreceding
page
ASF sensor check
No
BJ cartridge check
ASF sensor error
Cleaning
Cover open check
Carriage moves to cartridgereplacement position
OpenOpen/Closed?
I/F busy canceled
Ink sensor check
Normal?
Ink sensor error
I/F busy canceled
Cartridge installationerror
No-cartridge error
Yes
Yes
Normal (ON)?
NoNormal?
Closed
Cartridge error
END
2.3 Troubleshooting Problems
Part 2: Troubleshooting BJC-6200
2-6
ProblemPower does not come on
No printing
White stripes or smearing
appear
Soiled paper
Spur tracks appear
Broken vertical lines
Error does not occur at
ink-out
Abnormal noise
Probable Cause / Check ItemsAC adapter, control board, DC cable.
BJ cartridge, purge unit, ink tank, or
orange cap/tape still affixed to print
head.
BJ cartridge, faulty BJ cartridge
contacts, cartridge ribbon cable, purge
unit, control board, ink tank.
Ink mist, etc., at the platen's paper guide
plate is soiling the paper.
Check for any ink adhering to the paper
transport parts. (The paper is already
soiled when it reaches the platen.)
Deformed spur tips.
Paper thickness lever not properly set.
The nozzle check pattern's printout is
misaligned.
Guide shaft not greased properly.
Faulty carriage motor.
Ink sensor, control board
LF motor 2-step gear, purge unit, sheet
feeder unit, orange cap still attached to
the print head.
SolutionReplace faulty part.
Replace faulty part.
Replace faulty part.
Use a soft cloth dampened with water to
clean.
Disassemble the paper transport parts
and use a soft cloth dampened with
water to clean. Pass several sheets
through.
Replace the spur unit.
Set it to the proper position.
Readjust the printing position.
Apply proper amount of grease on the
stipulated parts.
Replace carriage motor.
Replace faulty part.
Replace faulty part.
2.4 Troubleshooting With Error Indications1) Error indication when a user-recoverable error occurs
The indicator indicates an error by blinking in orange for a certain number of times.After it blinks in orange to indicate the error, it blinks once, long, in green. This indication is repeated.
2) Error indication when an error un-recoverable by the user occursThe indicator indicates an error by blinking alternately in orange and green for a certain number oftimes.After it blinks in orange and green to indicate the error, it blinks once, long, in green. This indication isrepeated.
* The error code is displayed by the computer. With the iMac and Power Macintosh G3, a "D" or "M"is appended to the beginning of the error code.
** The waste-ink warning can be canceled by pressing the RESUME button.*** Error information for internal errors is not displayed nor indicated.
You can check it by printing the EEPROM information. See 7.3 Printing the EEPROMInformation on page 2-30.
**** If a ROM or RAM error occurs, the error indication might not be correct.
Table 2-1 ERROR INDICATIONS
Indicator Error Description Probable Cause and Suspected PartsBlinking Code*
User-Recoverable Errors--- Paper feed error Cause: Paper feed does not work even when the
paper feed operation is attempted.Suspect: Paper feed section, sheet feeder unit,paper-end sensor, control board
--- Paper jam error Cause: The paper is not ejected, even when thepaper ejection operation is attempted for 23inches.Suspect: Paper feed section, paper-end sensor,control board
--- Out of ink error Cause: No ink in the respective ink tank (inkcompartment and sponge).Suspect: Ink tank
--- Cartridge installation error Cause: The wrong cartridge (BJ cartridge orscanner cartridge) is installed in the carriage forprinting or scanning.Suspect: BJ cartridge, scanner cartridge
--- No-cartridge error Cause: No cartridge has been installed.Suspect:
--- Cartridge error Cause: The cartridge installed is defective.Suspect: BJ cartridge
1 User-recoverable errors are indicated by the specified number of blinks in orange, followed by a longblink in green, repeated.
2-7
BJC-6200 Part 2: Troubleshooting
Troubleshooting
2 times inorange 1
3 times inorange 1
4 times inorange 1
5 times inorange 1
6 times inorange 1
7 times inorange 1
--- Waste-ink warning** Cause: The total waste-ink count recorded in theEEPROM exceeds 95% of the stipulated amountindicating waste-ink full.Suspect: Waste-ink absorber, control board
--- Auto Print Position Adjustment Cause: Auto head position adjustment problemoccurred.Suspect: BJ cartridge, ink tank, printing positionsensor, control board carriage ribbon cable
1 User-recoverable errors are indicated by the specified number of blinks in orange, followed by a longblink in green, repeated.
Non User-Recoverable Errors--- ROM error**** Cause: ROM check failed during initialization.
Suspect: ROM, control board--- RAM error**** Cause: RAM check failed during initialization.
Suspect: DRAM, MPU & print controller,control board
6800 EEPROM error Cause: EEPROM cannot be written to properly.Suspect: EEPROM, MPU & print controller,control board
5100 Home position error Cause: The carriage's home position cannot bedetected because the home position sensor isfaulty (disconnected, etc.).Suspect: Home position sensor, purge unit,carriage motor, paper feed motor, control board,carriage ribbon cable, carriage board, DC cable
5400 Internal temperature sensor error Cause: The temperature sensor (TH501) on thecontrol board is faulty (disconnected, etc.).Suspect: Thermistor, control board
5B00 Waste ink-full error Cause: The waste-ink absorber reached 100% ofthe waste-ink capacity.Suspect: Waste-ink absorber, control boardSolution: Reset the EEPROM, replace waste-inkabsorber, replace control board
5200 Cause: The print head's temperature isabnormally high.Suspect: BJ cartridge, control board, no ink inink tank
Non User-Recoverable Errors are indicated by the specified number of blinks in orange and green,followed by a long blink in green, repeated.
Abnormal print headtemperature error
Part 2: Troubleshooting BJC-6200
2-8
8 times inorange
9 times inorange
1 time in orange/green2 times in orange/green
3 times in orange/green
4 times in orange/green
5 times in orange/green
6 times in orange/green
7 times in orange/green
5200 Cause: Faulty temperature sensor in the BJcartridge.Suspect: BJ cartridge, control board
5600 No cartridge error Cause: The cartridge cannot be detected otherthan at the cartridge replacement position.Suspect: Cartridge, control board, carriageboard, carriage ribbon cable.Improper contact between cartridge and carriage.
5700 ASF sensor error Cause: During the pick-up operation, the pick-uproller does not rotate, or, the pick-up rollersensor cannot detect the pick-up roller flag.Suspect: Sheet feeder unit, purge unit, controlboard
5210 Scanner cartridge error Cause: Faulty data in the scanner cartridge.Suspect: Scanner cartridge, control board
5000 Recovery system error Cause: While AP motor or LF motor runs, thePG sensor does not turn ON or OFF. Suspect: Purge unit, AP motor, LF motor,control board
Internal Error--- Ink sensor Cause: The check by the ink sensor during
initialization indicates that ink is available whenthere is none. The ink sensor does not check theink until the AC power is turned off. In this case,the ink compartment is always recognized tohave ink.Suspect: Control board, ink sensor, ink tank,EEPROM
Print head temperature sensor(diode sensor) error
2-9
BJC-6200 Part 2: Troubleshooting
Troubleshooting
8 times in orange/green
9 times in orange/green
10 times in orange/green
11 times in orange/green12 times in orange/green
No error indication
error***
3. DISASSEMBLY AND REASSEMBLY
3.1 Cautions for Disassembly and Reassembly3.1.1 Ink stains (Ink path/ink mist)
During servicing, be careful not to touch the ink path and get ink stains on the printer, work table, andyour hands and clothing.The ink path includes the BJ cartridge's ink tank supply inlet, the BJ cartridge's ink filter, the ink nozzlesand maintenance jet receptacle, head cap, wiper, and waste-ink absorber.Also, a printer that has seen long-term use or heavy-duty use may have ink mist soiling the platen, insidethe front cover, and purge section.Such soiled parts can soil the paper or your hands and clothing during servicing. To prevent this, use asoft cloth dampened with water to clean the parts thoroughly.
3.1.2 Static electricity damageThe rubbing of clothing can build up static electricity within the human body. Static electricity candestroy electrical components or alter the electrical characteristics of components.Never touch the ink sensor's contacts or the contacts on the BJ cartridge on the carriage.
3.1.3 Spur tips deformationBe careful not to deform the spur tips.The spur tips contact the paper after the printing. Since the spur tips' contact area is small, any inkadhering to the spur will be a minuscule amount that can be wiped off by the spur cleaner. It thereforewill not soil the paper. However, if the spur's tips are bent of out of shape, the contact area with the paperwill be larger, resulting in a larger amount of ink adhering to the spur, which might not be completelycleaned. The spurs will then soil the paper with dotted lines.
3.1.4 Feed gear damageWhen disassembling or reassembling the printer, do not touch the paper feed gears (feed roller gear andfeed drive gear). Note that even a slight scratch on the paper feed gear will cause irregular paper feedingduring high-quality printing.
3.1.5 Tap screw removal and installationThe printer uses tap screws to fasten the printer unit and base. The removed tap screws will have residuefrom the mold in which the internal thread was made. Since the residue may crush the screw threads,clean off the residue from the tap screws before re-installing them, or use new tap screws.
Part 2: Troubleshooting BJC-6200
2-10
3.2
Exp
lode
d V
iew
Fig
ure
2-2
Exp
lode
d V
iew
BJC-6200 Part 2: Troubleshooting
2-11
Troubleshooting
3.3 Disassembly and ReassemblyCautions for disassembling and reassembling the printer are stated below.As for the disassembly procedure, refer to the Parts Catalog. The illustrations in the Parts Catalog arenumbered according to the order of disassembly.
3.3.1 Carriage lock releaseNormally, when a cartridge is installed on the carriage and the power is turned off, the printer moves thecarriage to the capping position to lock it.And when the power is turned on, the carriage lock is normally released. However, if the printer does notoperate properly, you can release the carriage lock manually as shown in the illustration below. Removethe cartridge, and while holding down the purge unit's lever, move the carriage to the left. This releasesthe carriage lock.
3.3.2 Removing and installing tap screwsThe printer uses tap screws to fasten the printer unit and base. The removed tap screws will have residuefrom the mold in which the internal thread was made. Since the residue may crush the screw threads,clean off the residue from the tap screws before re-installing or use new tap screws.
2-13
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Figure 2-3 Carriage Lock Release
3.3.3 Removing the upper cover unitTo remove the upper cover unit, see the figure below.1) Unhook the upper cover unit's four hooks on the sides and back.2) Unhook the two hooks on the front.To reinstall, follow this procedure in reverse.
3.3.4 Removing the printer unitRemove the printer unit as shown in the figure below.1) First remove the two screws securing the printer unit and bottom case.2) Release the bottom case's two hooks at the back of the printer unit. (Arrows 1 and 2)3) Hold the two handles on the sides of the printer unit and lift up at an angle as shown by arrow 3.
Part 2: Troubleshooting BJC-6200
2-14
Figure 2-4 Upper Cover Unit Removal and Installation
1
2
3
3
Screw
Figure 2-5 Removing the Printer Unit
3.3.5 Removing the pressure roller unitTo remove the pressure roller unit, release the three hooks in turn as shown by the arrows in the figure.Then pull it out from rear of the printer unit.When releasing the hooks, start with the one on the left (when facing the front of the pressure roller unit).This will make removal easier.
3.3.6 Spur positions on the spur base unitThe figure below shows the position of the spurs on the spur base. The side (bottom) where the spurs areinstalled is shown. If you removed any of the spurs by mistake, use this diagram to install then at thecorrect position.
2-15
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Figure 2-6 Removing the Pressure Roller Unit
Spur positions
Spur positions
Figure 2-7 Spur Positions on the Spur Base Unit (Bottom View)
3.3.7 Removing the ASF unit
3.3.8 Removing the head gap adjustment sectionSecured to the printer frame, the head gap adjustment plate is for adjusting the gap between the BJcartridge's nozzles and platen so that the optimum printing quality is obtained.If the set screw securing the head gap adjustment plate to the printer frame is loosened, the head gap willchange and head gap adjustment will be necessary.The set screw is painted in red to distinguish it from the other screws and to prevent accidental loosening.If you have loosened it by mistake, do the head gap adjustment as described in 3.4.6 Adjusting thehead gap on page 2-21.
Part 2: Troubleshooting BJC-6200
2-16
Set screw
Set screwASF unit
Figure 2-8 Removing the ASF Unit
L
Head gapadjustmentplate
Head gapadjustmentplate
Figure 2-9 Carriage Shaft Position Adjustment Bearing
3.4 Adjustments and Settings After Disassembly and Reassembly3.4.1 Adjustments
(1) User Level
(2) Serviceman Level
When applying grease, be careful not to get any grease on the wiper and cap.
2-17
BJC-6200 Part 2: Troubleshooting
Troubleshooting
TimingAfter BJ cartridgeinstallation/removal
AdjustmentBJ cartridge printing positionadjustment
Time Required2 min.
Tools Required2 sheets of B5 or largerpaper
TimingAfter idler pulleyinstallation/removalAfter control boardreplacement or waste-inkabsorber replacementAfterreplacement/disassemblyof carriage unit partsAfter loosening the headgap set screwsParts to be greased
AdjustmentBelt tension
EEPROM setting
BJ cartridge printing positionadjustment
Head gap
See page 2-18
Time Required1 min.
1 min.
2 min.
5 min.
---
Tools RequiredTension spring (QY9-0043)None
2 sheets of B5 or largerpaper
Gap gauge (QY9-0038)Grease PG-641 (CK-0562), Floil 946P, brush
3.4.2 Applying greaseApply the correct grease to the places shown below.Use a flat brush to spread a thin coat of grease.To disassemble and reassemble the printer, refer to the Parts Catalog.
When applying grease, be careful not to get any grease on the wiper and cap.
Part 2: Troubleshooting BJC-6200
2-18
Carriage shaft friction surface(No dripping)Floil 946P
Rear of carriage rail(Apply on entire surface)Approx. 48 mg (Molykote PG-641)
Feed roller friction surfaces(Three places on back of platen)Approx. 14 mg x 3 places (Molykote PG-641)
Cam friction surfaceApprox. 27 mg (Molykote PG-641)
Pick-up roller friction surfaceApprox. 7 mg (Molykote PG-641)
Figure 2-10 Applying Grease
3.4.3 Print head position adjustmentSince the printer has two BJ cartridges installed, the ejected ink's placement can be thrown off due to thedifferences in the BJ cartridges and the installation conditions. Less than optimum printing quality willresult. To eliminate this misalignment, perform the auto print head position adjustment with the printerdriver's utility after installing the BJ cartridges. The print head position can also be adjusted in ServiceMode with the printer alone, without using a computer. The procedure is described in 7.1 Service ModeOperations on page 2-28.Place one B5 or larger sheet of plain paper in the auto sheet feeder, then start the test printing of the printhead position adjustment pattern with the printer driver's utility sheet.
Printing the nozzle check pattern requires B5 or larger paper. If the paper's width isnarrower than the nozzle check pattern, the platen will be printed on and the ink will soilthe platen.
2-19
BJC-6200 Part 2: Troubleshooting
Troubleshooting
LED Calibration
360 dpi vertical position adjustment
360 dpi bi-directional rough adjustment
360 dpi bi-directional fine adjustment
180 dpi bi-directional rough adjustment
180 dpi bi-directional fine adjustment
360 dpi horizontal position forwarddirection rough adjustment
360 dpi horizontal position forwarddirection fine adjustment
360 dpi horizontal position returndirection rough adjustment
360 dpi horizontal position returndirection fine adjustment
180 dpi horizontal position forwarddirection rough adjustment
180 dpi horizontal position forwarddirection fine adjustment
180 dpi horizontal position returndirection rough adjustment
180 dpi horizontal position returndirection fine adjustment
720 dpi horizontal position forwarddirection rough adjustment
720 dpi horizontal position forwarddirection fine adjustment
1440 dpi horizontal position forwarddirection rough adjustment
1440 dpi horizontal position forwarddirection fine adjustment
Printing position check pattern
Figure 2-11 Print Position Adjustment Pattern
3.4.4 Setting the EEPROMAfter replacing the control board or waste-ink absorber, reset the EEPROM, set the model settings, anddo a test printout to confirm the settings.The EEPROM (IC502) on the control board stores various printer data such as the waste-ink amount andother printer specific settings.The procedure is described in 7.1 Service Mode Operations on page 2-28.
(1) After control board replacementIf the waste-ink absorption amount is over 7 percent at the time you replace the control board, alsoreplace the waste-ink absorber. Then reset the EEPROM and restore the printer settings.To check the waste-ink absorption amount, you can either check the service/factory text printout fromthe old control board or visually check the waste-ink absorber's waste-ink absorption amount.Also, the new control board (EEPROM) data is undefined.The EEPROM must be reset. Otherwise, the waste-ink full error will not occur, even when the waste-ink absorber's capacity has been exceeded, thereby leaking ink.
(2) After waste-ink absorber replacementClear the EEPROM's waste-ink counter.
Once the data in the EEPROM is reset, a test printout cannot be used to confirm the olddata. Be sure to print the data before resetting the EEPROM.The various settings (except the model setting), sheet count, and waste-ink amount will bereset.The various settings and waste-ink amount stored in the old EEPROM cannot be written tothe new (replacement) EEPROM.
The waste-ink full error is expected to occur only when the printer prints more than thenumber of sheets specified for its service life. However, how soon this error occurs variesdepending on how many times the printer has been turned on/off, the number of times theBJ cartridge has been replaced (front cover open/closing), and the operating environment.
3.4.5 Adjusting the carriage belt tensionIf the carriage belt tension has been loosened to remove the carriage, etc., adjust the carriage belt tension.When securing the pulley assembly, use the tension spring (QY9-0043) and tighten the screws. Aftertightening the screws, remove the tension spring.
Part 2: Troubleshooting BJC-6200
2-20
ScrewsTension spring
Idler pulley
Figure 2-12 Carriage Belt Tension Adjustment
3.4.6 Adjusting the head gapIf the set screws securing the head gap adjustment plate to the printer frame are loosened or removed, thehead gap adjustment will be necessary.
Preparation1) Remove the upper cover unit and bottom case. (Or, reassemble the printer so that the upper cover
unit and bottom case are to be attached next.)2) Remove the paper thickness lever spring and the left and right shaft clips, then attach the bottom
case.3) Loosen the red set screws on both sides of the printer chassis by a half rotation from the fully
tightened position.4) Set the paper thickness lever to the down position (for thick paper).
Before doing the adjustment, make sure the gap gauge is not deformed and that no foreignmatter is adhering to it or to the platen.
2-21
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Red setscrew
Red setscrew
Head gapadjustment plate
(right side)Head gapadjustment
plate (left side)
Shaft clip
Black BJ cartridge Paper thickness lever
Carriage belt
Paper thickness lever spring
Normal paper positionThick paper position
Figure 2-13 Head Gap Adjustment 1
Adjustment Procedure1) Set the gap gauge (QY9-0038) to position A1.2) Move the carriage belt by hand so that the carriage goes to position A2. Align the bottom case's rib
with the carriage's right end.3) Install a black BJ cartridge without ink tank in the carriage.4) Move the paper thickness lever up and down two or three times, then, while holding the lever in the
normal paper (up) position, tighten the red set screw on the right end.5) Remove the black BJ cartridge.6) Place the gap gauge at position B1.7) Set the paper thickness lever to the thick paper (down) position.8) Move the carriage belt by hand so that the carriage goes to position B2. Align the ink sensor's edge
with the carriage's left end.9) Install a black BJ cartridge without ink tank in the carriage.10) Move the paper thickness lever up and down two or three times, then while holding the lever in the
normal paper (up) position, tighten the red set screw on the left end.11) Remove the black BJ cartridge.12) Loosen the red set screw on the right end by a half turn. Then repeat steps 1) to 5) to complete the
adjustment.
Remove the bottom case and attach the paper thickness lever spring and the left and right shaft clips.
Part 2: Troubleshooting BJC-6200
2-22
Position A1 Position A2
Position B1 Position B2
QY9-0054
QY9-0054QY9-0038
QY9-0038
Align the bottom case's ribwith the carriage's right end.
Align the ink sensor cover'sedge with the carriage's left end.
Figure 2-14 Head Gap Adjustment 2
4. OPERATION CHECK AFTER DISASSEMBLY AND REASSEMBLY
4.1 Check ProcedureAfter disassembly and reassembly, follow the procedure below to check the printer's operation.
1) After service/factory test printout with the printer aloneCheck that the printer can print properly. The procedure is described in 7.1 Service Mode Operationson page 2-28.
After replacing the control board or the ink absorber, the following check procedure is also necessary inaddition to 1) above.
2-23
BJC-6200 Part 2: Troubleshooting
Troubleshooting
After control board replacement
After waste ink absorberreplacement
The service/factory test printout must show the correct ROM version andmodel designation. It must also show the printed sheet count and that thetotal waste-ink amount has been cleared. The printer driver must be able toprint the nozzle check pattern.The service/factory test printout must show that the total waste-ink amounthas been cleared.
5. TRANSPORTING THE PRINTER
Before moving or transporting the printer, put one BJ cartridge (with the ink tank installed) in the cartridgecontainer. This is to prevent the ink from leaking and the BJ cartridge's ink nozzles from drying up.Before returning the repaired printer back to the customer, move the carriage to the cartridge replacementposition and tape it at that position.
5.1 Preparation for TransportWhen transporting the printer, follow the procedure below.1) With the printer turned on, open the front cover and move the carriage to the cartridge replacement
position.2) Remove one cartridge from the carriage and put it in the cartridge container.3) Turn off the printer by pressing the POWER button.4) Then, from Service Mode, conduct the power off/carriage lock procedure.
For details, refer to 7.1 Service Mode Operations on page 2-28.5) Disconnect the interface cable (s).6) Disconnect the AC plug from the power outlet.7) Close the front cover.8) Pack the printer in its original packaging. If you do not have the original packaging, use sufficient
cushioning material when packing the printer.
Part 2: Troubleshooting BJC-6200
2-24
6. PARTS REPLACEMENT, PERIODIC INSPECTIONS, & TOOLS
6.1 Parts Replacement
6.2 Periodic Inspections
6.3 Tool List
2-25
BJC-6200 Part 2: Troubleshooting
Troubleshooting
LevelUserServiceman
Periodically Replaced PartsNoneNone
LevelUserServiceman
Periodic InspectionsNoneNone
LevelUser
Serviceman
ConsumablesBlack BJ cartridge: BC-30Color BJ cartridge: BC-31Photo BJ cartridge: BC-32Black BJ cartridge ink tank (Black: BCI-3BK)Color BJ cartridge ink tank(Black: BCI-3BK, Cyan: BCI-3C, Magenta: BCI-3M, Yellow: BCI-3Y)Photo BJ cartridge ink tank(Black: BCI-3BK Photo, Cyan: BCI-3C Photo, Magenta: BCI-3M Photo)None
Ordinary ToolsPhillips screwdriverBlade screwdriverNeedle-nosed pliersTweezersFlat brushMulti-meter
RemarksFor the removal and installation of screws.For the removal of plastic parts.For the removal and installation of springs.For the disconnection and connection of flexible cables, etc.For applying grease.For troubleshooting.
Special Tools (Part No.)Gap gauge 2.3 mm
(QY9-0054-000)Tension spring
(QY9-0043-000)Grease Molykote PG-641
(CK-0562-000)Grease FLOIL 946P
(QY9-0045-000)
RemarksFor Head gap adjustment (see Figure 2-14 on page 2-22). Use 1.For carriage belt tension adjustment (see Figure 2-12 on page 2-20).
To be applied on the specified parts (see Figure 2-10 on page 2-18).
To be applied on the specified parts (see Figure 2-10 on page 2-18).
6.4 Operation with the Printer's Operation PanelThe printer can be operated in the offline operation mode, with the power turned on and withoutconnection to a computer.With the printer turned on, you can start various printer operations by holding down the RESUME buttonand releasing after the green indicator blinks the stipulated number of times.
6.4.1 CleaningWith the printer turned on, hold down the RESUME button and release after the green indicator blinksonce. The cleaning will then start. Cleaning can also be performed from the printer driver's utility, whileconnected to a computer.
6.4.2 Printing the nozzle check patternWith the printer turned on, hold down the RESUME button and release after the green indicator blinkstwice. The printer will then start printing the nozzle check pattern. If any printing defects appear in thetest printout, clean the BJ cartridges. If printing defects persist even after cleaning the BJ cartridges fivetimes or more, replace the BJ cartridges.
Printing the nozzle check pattern requires B5 or larger paper. If the paper's width isnarrower than the nozzle check pattern, the platen will be printed on and the ink will soilthe platen.
To stop the printing of the test pattern midway, press the POWER button. The printing will stop and the sheet will be discharged. Then the printer will turn off.
Part 2: Troubleshooting BJC-6200
2-26
OperationCleaningNozzle check pattern printoutRoller cleaning---
Indicator Blinking1 time2 times3 times4 times
Remarks---Stops after 1 sheet is printed.Passes one cleaning sheet through.No operation executed.
6.4.3 Roller cleaningWith the printer turned on, hold down the RESUME button and release after the green indicator blinksthree times. The roller cleaning will then start. The cleaning sheet placed in the auto sheet feeder will besent through, and the paper fibers, etc., will be cleaned from the pick-up rollers and paper feed rollers.
2-27
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Black BJ cartridge
Large-dot printing by the 1st nozzle
Large-dot printing by the 160th nozzle
Large-dot printing by the 1st nozzle
Large-dot printing by the 48th nozzle
Black
48 nozzles
48 nozzles
48 nozzles
Yellow
Cyan
Magenta160 nozzles
Large-dot printing
Small-dot printing
Color BJ cartridge
Small-dot printing by the 1st nozzle
Small-dot printing by the 48th nozzle
(X1)
(X2)
(X3)
(X4)
(X5)
(X6)
(B1)
(B2)
360 dpi vertical position
360 dpi bi-directional
180 dpi bi-directional
360 dpi horizontal position forward direction
360 dpi horizontal position return direction
180 dpi horizontal position forward direction
180 dpi horizontal position return direction
720 dpi horizontal position forward direction
720 dpi horizontal position return direction
Small-dot printing by the 1st nozzle
Small-dot printing by the 160th nozzle
(Y)
Figure 2-15 Nozzle Check Pattern Printout (Color Sample)
7. SERVICE-RELATED FEATURES
The printer has a Service Mode for accessing service settings and executing test printouts. The operationscan be selected via the operation panel buttons.
7.1 Service Mode Operations1) With the printer turned off, hold down the RESUME button and press and hold the POWER button
(the green indicator lights).2) While holding down POWER button, release the RESUME button and then press the RESUME button
twice in succession. Then release both the RESUME button and POWER button.(Each time the RESUME button is pressed, the indicator's color toggles between orange and green.)
3) During the printer initialization, the green indicator blinks. When the green indicator stops blinking andlights on, press the RESUME button the stipulated number of times to execute the desired operationlisted below.(Each time the RESUME button is pressed, the indicator's color toggles between orange and green.)
4) After making the selection, press the POWER button. The green indicator lights and the function willbe executed.(After the function is executed, the printer will power off.)
* After selecting model setting, press the RESUME button the number of times indicated below to setthe product type.(During the initialization, the green indicator blinks. Each time the RESUME button is pressed, theindicator's color toggles between orange and green.)
After selecting the model, press the POWER button to finalize the setting.(After the printer executes the function, it will turn off.)
Before entering the service mode, install the BJ cartridges. The service mode cannot beexecuted without the cartridges installed.After setting the model, confirm the setting with the service/factory test printout.
Part 2: Troubleshooting BJC-6200
2-28
Press0 times1 time2 times
3 times4 times5 times6 times
7 times or more
IndicatorLights in greenLights in orangeLights in green
Lights in orangeLights in greenLights in orangeLights in greenLights in orange
FunctionService/factory test printoutEEPROM information printoutEEPROM initialization (All the information will be reset to the
default, except for the model setting.)
Clears the waste-ink counterModel setting*: The setting procedure is described below.Ink availability check and printAuto print head position adjustmentPower off/Carriage lock
Press0 times1 time
2 times or more
IndicatorLights in greenLights in orange
---
FunctionBJ F620 (Japan)BJC-6200 (All other countries)Saved as a reserved area where the setting will not be rewritten.
7.2 Service/Factory Test PrintoutThe header of the service/factory test printout shows the control ROM version, model setting, total printedsheet count, total waste-ink absorption amount, and other information.
* USB serial No.If multiple BJS-6200 printers are connected via USB, each printer will have a unique USB serial No. (inaccordance with USB standards) so that the computer can distinguish between them.The unique USB serial No. is written in the EEPROM when the control board is manufactured. The USBserial No. written in the EEPROM is not cleared even when the EEPROM is reset. Also, the USB serialNo. cannot be modified.
2-29
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Installed cartridges
Model designation Total printed sheet count with black/colorBJ cartridge
ROM version
Total printed sheet count with photo/color BJ cartridge
Total waste-ink amount (Waste-ink absorber's absorption capacity: %)Serial No.* for USB
ROM Ver Vx.xx BJC-6200 Use Head <BC-30,BC-31> HeadTemp0=031.0 HeadTemp1=032.5 EnvironmentTemp=031.0 Bk=00000 C1=00257 Ph=00000 Sc=00000 ScC1=00000Factory Area=01 00 00 00 00 01 1B 89 LostInkCount =03.9% Destination =01 USBSerialNo=(109BNF)
Total passed sheet countwith scanner cartridge
Unused
Unused
Figure 2-16 Service/Factory Test Printout (Sample)
7.3 Printing the EEPROM InformationThe EEPROM stores information such as the various settings; the total printed sheet count of the black,color, and photo BJ cartridges and scanner cartridge; the total waste-ink absorption amount; and the errorhistory of the last three non user-recoverable errors. The information stored in the EEPROM is printed inthe hexadecimal dump format in the EEPROM information printout. The EEPROM information serves as ageneral guide to how much the printer has been used.
Part 2: Troubleshooting BJC-6200
2-30
The error history records the last three (starting with the most recent one) non user-recoverable
errors that have occurred. It does not include ROM/RAM errors. The error codes are
shown in ASCII format.
Error Error Code ASCII Code
Carriage error 5100 35 31 30 30
Abnormal head temperature 5200 35 32 30 30
Scanner cartridge error 5210 35 32 31 30
Abnormal internal temperature error 5400 35 34 30 30
No head error (in operation) 5600 35 36 30 30
ASF sensor error 5700 35 37 30 30
Ink sensor error 5910 35 39 31 30
Waste-ink full error 5B00 35 42 30 30
Pump sensor error 5C00 35 43 30 30
EEPROM Read/Write error 6800 36 38 30 30
- EEPROM Information <Hex.> -Address +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F00000000 05 20 00 0A 00 00 B8 83 00 0C 9F 40 09 35 1C 2800000010 00 00 00 00 2A 6A 51 A1 38 54 AA A0 1E 16 DA 3C00000020 35 6C B7 AB 33 BC E9 71 32 DD 02 0C 00 00 00 0000000030 14 00 0A 07 04 02 02 02 00 00 00 00 0A 80 00 0000000040 04 90 00 08 00 00 00 44 00 00 00 44 00 00 00 4400000050 00 00 00 00 00 00 04 44 00 00 00 00 00 00 02 B900000060 00 00 00 1D 00 58 00 1B 00 01 00 2F 00 06 00 0000000070 00 00 00 00 00 00 00 08 00 00 00 08 00 00 00 0800000080 00 00 00 72 00 00 00 2E 00 00 00 30 83 00 00 0000000090 3C 00 00 10 10 0C 0C 08 0C 10 0C 0C 0C 10 0C 0C000000A0 0C 04 00 08 00 0C 0C 00 FD 07 00 00 04 04 00 00000000B0 00 00 00 00 04 04 00 00 00 00 00 00 00 00 00 00000000C0 00 00 00 00 15 0B BB 19 35 1A D5 C6 13 0A 46 61000000D0 04 19 57 AB 98 1A 72 13 00 45 93 6B 46 34 63 E3000000E0 35 36 30 30 35 36 30 30 35 36 30 30 FF FF FF F0000000F0 00 00 00 D6 67 7C 73 FF 01 FF FF FF FF FF FF FF
Error history 1 Error history 2 Error history 3
Figure 2-17 EEPROM Information Printout (Sample)
7.4 Resetting the EEPROMThe EEPROM stores information such as the various settings; the total printed sheet count of the black,color, and photo BJ cartridges and scanner cartridge; the total waste-ink absorption amount; and the errorhistory of the last three non user-recoverable errors. The printer uses the total waste-ink absorption amountrecorded by the EEPROM as the basis for determining whether the waste ink is full. Therefore, afterreplacing the waste-ink absorber, be sure to reset the EEPROM's total waste-ink absorption amount.Also, after replacing the control board, be sure to reset the new control board's EEPROM and to alsoreplace the waste-ink absorber.
7.5 Setting the Model with the EEPROMThe control board used in the BJC-6200 is also used in other printers. After replacing the control board, thedefault information for the respective printer must be set.After setting the model, confirm it with the service/factory test printout.
7.6 Ink Availability CheckWhen this function is selected, the printer scans the carriage to check for ink in the ink tank's inkcompartments. The result is printed out.Whether the ink sensor is working properly can be confirmed by:(1) Installing an empty ink tank in the BJ cartridge.(2) Using this Service Mode function and print out the results.(3) Checking that the "ExistInk" value is 0 (indicating an empty ink tank).
7.7 Auto Print Head Position AdjustmentThe print head position can be adjusted with the printer alone, without connection to a computer. Theadjustment is the same as when the user executes the auto printing position adjustment via the computer.For details on the head printing position adjustment, see 3.4.3 Print head position adjustment on page2-19.
7.8 Power Off/Carriage LockWhen this function is selected, the printer moves the carriage (whether BJ cartridges are installed or not) tothe home position and locks the carriage. Then the power turns off.
2-31
BJC-6200 Part 2: Troubleshooting
Troubleshooting
Part 2: Troubleshooting BJC-6200
2-32
This page intentionally left blank
Part 3
APPENDIX
Page3 - 1 1. TECHNICAL REFERENCE3 - 1 1.1 Print Mode List3 - 2 1.2 Purge Unit's Capping and Cleaning Functions3 - 2 1.3 Cautions About the Inks3 - 3 1.4 Operation with a Computer3 - 4 1.5 Detection Functions by Sensors3 - 5 1.6 Electronic Circuit Description3 - 6 2. CONNECTOR LOCATIONS AND PIN CONFIGURATIONS3 -10 2.1 Carriage Board3 -11 2.2 BJ Cartridge3 -12 2.3 Scanner Cartridge (Optional)3 -13 2.4 AC Adapter3 -13 2.5 DC Power Cable3 -14 2.6 Carriage Motor3 -14 2.7 Paper Feed Motor3 -14 2.8 ASF Motor3 -15 2.9 Ink Sensor3 -15 2.10 Printing Position Sensor3 -15 2.11 Purge Sensor Connector3 -17 2.12 Circuit Diagrams
1. TECHNICAL REFERENCE
1.1 Print Mode ListThe print mode list for the black, color, and photo BJ cartridges is shown below.By setting the printer driver's "Dithering," "Paper Type," and "Printing Quality" settings, the printer willoperate in the printing modes below.
Table 3-1 PRINT MODE LIST
3-1
BJC-6200 Part 3: Appendix
Ap
pen
dix
Black/Color Cartridge
Printing Quality
Dithering Paper Type High-speed Standard (Faster Speed) Standard (Higher Quality) High Quality Highest Quality
180 × 180 L/R 360 × 360 L/R 360 × 360 L/S/R 720 × 720 S/R 1440 × 720 S/R
Error Dispersion Plain paper --- 1 pass/bi-directional 2 passes/uni-directional 4 passes/uni-directional ---
High quality --- 2 passes/bi-directional 3 passes/uni-directional (4 passes) 4 passes/uni-directional 4 passes/uni-directional
Glossy --- --- 4 passes/uni-directional 6 passes/uni-directional (8 passes) 6 passes/uni-directional (8 passes)
Glossy film --- --- 4 passes/uni-directional 6 passes/uni-directional (8 passes) ---
Photo card --- --- 3 passes/uni-directional 4 passes/uni-directional 4 passes/uni-directional
T-shirt transfer --- --- 6 passes/uni-directional --- ---
Back print film --- --- 6 passes/uni-directional L/L --- ---
Transparency --- 2 passes/uni-directional 4 passes/uni-directional L/L --- ---
Envelope --- 1 passes/uni-directional 3 passes/uni-directional (4 passes) 4 passes/uni-directional ---
Pattern Plain paper 1 pass/bi-directional 1 pass/bi-directional --- --- ---
High quality --- 2 passes/bi-directional --- --- ---
Envelope --- 1 pass/uni-directional --- --- ---
Pattern (High speed) Plain paper 1 pass/bi-directional 1 pass/bi-directional --- --- ---
High quality --- 2 passes/bi-directional --- --- ---
Auto Plain paper 1 pass/bi-directional 1 pass/bi-directional --- --- ---
High quality --- 2 passes/bi-directional --- --- ---
Photo/Color Cartridge
Printing Quality
Dithering Paper Type High-speed Standard (Faster Speed) Standard (Higher Quality) High Quality Highest Quality
180 × 180 L/R 360 × 360 L/R 360 × 360 L/L/R 360 × 360 L/S/P 720 × 720 S/P
Error Dispersion Plain paper --- 1 pass/bi-directional --- 2 passes/uni-directional 4 passes/uni-directional
High quality --- 2 passes/bi-directional --- 3 passes/uni-directional 4 passes/uni-directional
Glossy --- --- --- 4 passes/uni-directional 6 passes/uni-directional
Glossy film --- --- --- 4 passes/uni-directional 6 passes/uni-directional
Photo card --- --- --- 3 passes/uni-directional 4 passes/uni-directional
T-shirt transfer --- --- 6 passes/uni-directional --- ---
Back print film --- --- 6 passes/uni-directional --- ---
Transparency --- 2 passes/uni-directional 4 passes/uni-directional --- ---
Envelope --- 1 pass/uni-directional --- 3 passes/uni-directional 4 passes/uni-directional
Pattern Plain paper 1 pass/bi-directional 1 pass/bi-directional --- --- ---
High quality --- 2 passes/bi-directional --- --- ---
Postcard --- 1 pass/uni-directional --- --- ---
Envelope --- 1 pass/uni-directional --- --- ---
Note 1: R and P indicate the ink used for printing. R is color inks (4 colors), and P is the photo inks (6 colors).
Note 2: L (large) and S (small) indicate the ink's dot size for multi-drop printing.
Note 3: The table also indicates the number of passes and the printing direction. If the number of passes differ in the gray scale mode, it is indicated in
parentheses.
1.2 Purge Unit's Capping and Cleaning FunctionsCapping is executed at the following times:• When the power is turned off with the POWER button.• When uncapped and print signals have not been received within the stipulated time during standby.
During paper feeding: After 20 min.Other times: After 30 sec.
• After the front cover has been left open for 10 minutes.
Cleaning is executed at the times listed in the table below.As ink suction is performed on both BJ cartridges simultaneously, ink suction for only one BJ cartridge isnot possible.
Table 3-2 INK CONSUMPTION DURING CLEANING (GENERAL GUIDE)
* In this case, cleaning is not immediately executed. Cleaning is executed the next time any of following isexecuted: Printing starts, soft power on, paper feeding, paper ejection. (Reason: When the preconditionsfor cleaning overlap, delaying the cleaning results in the cleaning being executed only once, reducing inkconsumption.)
1.3 Cautions About the InksAlthough the inks do not contain any substances harmful to humans, they do contain organic solvents.1) Black ink
Contains glycerin 56-81-5 and diethylene glycol 111-46-6.2) Yellow ink
Contains glycerin 56-81-5 and isopropyl alcohol 67-63-0.3) Cyan, magenta, photo cyan, photo magenta, photo black inks
Contain glycerin 56-81-5, isopropyl alcohol 67-63-0, ethylene glycol 107-21-1, and diethylene glycol111-46-6.
Do not consume the inks or get it into your eyes.Should ink get into your eyes, rinse with lots of water and consult a doctor.Should a large amount of ink be consumed by mistake, promptly see a doctor.Since the inks contain pigments, they will permanently stain clothing.
Part 3: Appendix BJC-6200
3-2
Ink Consumption (approx. mg)Printer StatusBlack Color Photo Color
Print head refreshing via the printer driver. 0.39 0.53 0.52 0.72Cleaning executed via the printer driver. 0.20 0.27 0.30 0.41Operation executed via printer's button. 0.20 0.27 0.30 0.4172 hours or more elapsed since the last cleaning. 0.20 0.27 0.30 0.41The printed dot count exceeds the stipulated dot count. 0.20 0.27 0.30 0.41Before a banner is printed (the dot count since the last 0.20 0.27 0.30 0.41cleaning exceeds the stipulated dot count, or the time since the last cleaning exceeds the stipulated time).Power is turned on (for the first time). 0.58 0.79 0.77 1.07Power is turned on (uncapped after AC connection). 0.39 0.53 0.52 0.72* Power is turned on (capped after AC connection). 0.20 0.27 0.30 0.41* At replacement of the BJ cartridge or ink tank. 0.39 0.53 0.52 0.72
1.4 Operation with a ComputerYou can set the printer's functions via the dedicated printer driver.
1.4.1 Setting functions with the printer driverYou can use the dedicated printer driver's utilities to set or execute the following:1) Cleaning2) Head refreshing3) Pick-up roller cleaning4) Nozzle check pattern printout5) Print head position adjustment6) Printer power off7) Automatic power setting8) Status monitor startup9) Special settings• Set the printer to ECP mode (Factory default: Disabled)• High-speed printing (Factory default: Enabled): Sets the printer's response time (ACKNLG) from 4 ms
to 0.9 ms.• Pause page (Factory default: Disabled)• Pause scan (Factory default: Disabled)• Execute automatic head position adjustment after BJ cartridge replacement (Factory default: Disabled)• Adjust head position manually (Factory default: Disabled)<<Special Menu for Users (User or Service Mode)>>The Special Menu for users can be accessed by holding down the Shift key and clicking the CustomSettings button.• Economy Cleaning (Factory default: Disabled)
The cleaning operations after the AC power is connected and the power turned on for the first time isdisabled. When the printer is being repaired or when it turns on in tandem with the computer turning on,the subsequent ink consumption can be reduced. However, this function is disabled if the power isturned on and over 72 hours elapse after the AC power supply is active.
• Prevent inter-sheet ink transfer (Factory default: Disabled)The ink transfer control prevents ink smearing caused by paper chafing during paper discharge whenthe black BJ cartridge is used for high-duty printing on plain paper. This ink transfer control can bedisabled. The discharged printed sheets can be removed individually to prevent lower throughput.
3-3
BJC-6200 Part 3: Appendix
Ap
pen
dix
Figure 3-1 Printer Driver Utilities (Sample)
1.5 Detection Functions by SensorsThe printer has the following sensors to detect the printer's operating status.
Part 3: Appendix BJC-6200
3-4
Purge sensor(Purge unit)
Printing position sensor(Carriage unit)
Paper-end sensor Home position sensor(Carriage unit)
Ink sensor
Pick-up roller sensorInternal temperaturesensor
Figure 3-2 Sensor Locations
1.6 Electronic Circuit Description1.6.1 Circuit block diagram
A block diagram of the printer's electronic circuit comprising the control board and carriage board isshown below.
1.6.2 Power source line block diagramThe printer uses an internal power voltage of 5 V/24 V/3.3 V. The power source line's block diagram isshown below.
3-5
BJC-6200 Part 3: Appendix
Ap
pen
dix
Control Board
Carriage board* Signal name when a
scanner cartridgeis used.
*DIA*DIK*RWR*REN*RDT
HSEL1A0,1HSEL1B0,1HSEL2A0,1HSEL2B0,1ODD,EVEN
BENB0,1HENB0-5SUBH0,1DIA0,1DIK0,1
DC/DC converter& reset IC
(IC501)
Driver IC(IC503)
Driver IC(IC401)
EEPROM (IC402) 2 Kbit
BJ cartridge
or
scanner cartridge
(optional)
Cartridge connector
BJ cartridge
RO
M_A
0-19
RO
M_D
0-15
8-Mbit
CE
A0-
19
D0-
15
48MHz(X101)
PM
PM
RAM_A0-9
RAM_D0-15
PB1-3
CS0X
RE
SE
TX
DRAM(IC103)
16-MbitMA0-9
MD0-15A0-9
D0-15
XT
1X
T2
PC2
PC1
Par
alle
lin
terf
ace
(CN
304)
Internal temperature sensor(TH401)
MP
U&
Prin
ter
Con
trol
ler
(IC
101)
Address bus ROM A0 - A19
Data bus ROM D0 - D15
Con
trol
RO
M(C
102)
Carriage motor
Paper feed motor
Paper-end sensor(PS401)
Pick-up roller sensor(PS402)
HVHHVDD
*VHLED*VDD
*DTCK*ST0*LNST*RST*SCHKR
PO0/INTP100
PO1/INTP101
CR_CLKCR_STB
CR_DATALF_CLKLF_STB
LF_DATAPD2
ANI1
POWER switch(SW401)
RESUME switch(SW402)
US
Bin
terf
ace
(CN
305)
Ink sensor(CN401 ← Ink sensor)
ST1/TST2ST2/SOT
ST3ST4/TST3ST5/TST4ST6/TST5
PC0
PO2/INTP102Front cover switch(SW403)
PA0PA1
Power indicatorError indicator
(LED401)
Home position sensor(PS1)
HDATA0,1HCLOCK0,1HRSTXHLATDIR
Printing position sensor(CN6 ← Printing position sensor)
P04/PWM1ANI3
ANI5
PM ASF motor
Purge sensor(CN402 ← Purge sensor) PC3
Figure 3-3 Block Diagram
Q203: Printing position sensor (CN202)Q401: Parallel interface (CN304)Q402: HP sensor (CN202)Q402: Pick-up roller sensor (PS402)Q402: Paper-end sensor (PS401)Q402: Purge sensor (CN402)Q403: Cartridge (CN203)Q404: Ink sensor (CN401)
Q301: USB interface (CN305)
DC
/DC
conv
erte
r&
rese
tIC
(IC
501)
Carriage motor (CN502)Paper feed motor (CN503)
Q204: Cartridge (CN201)
AC in
ASF motor (CN504)
Thermistor(TH401)
Motor driver(IC401)
Pow
er
sourc
ein
put
connecto
r(C
N501)
AC
adapte
r
OP amp(IC201)
EEPROM(IC402)
MP
U&
Prin
ter
Co
ntr
olle
r(I
C1
01
)
+24 VDC
+5 VDC
+3.3 VDC
+24 VDC
+24 VDC
+5 VDC
+3.3 VDC
+24 VDC
Motor driver(IC503)
Control ROM(IC102)
DRAM(IC103)
Figure 3-4 Power Source Line Block Diagram
2. CONNECTOR LOCATIONS AND PIN CONFIGURATIONS
Part 3: Appendix BJC-6200
3-6
CN504 CN502
1 4 1 4 CN
201
CN
202
CN
203
1
28
1
28
1
20
1
3
4
2
CN305
CN401
CN503
13
1 4
CN
304
1
18
19
36
1 15CN402 CN501
3
Figure 3-5 Control Board
CN503 CN502
CN304 CN305
Carriagemotor
Switchdetection
CN501
Paper-feedrollers
CN2CN1 CN3
CN202CN203CN201
BJ cartridgeor
scanner cartridge(optional)
Printpositionsensor
CN401
CN4
BJ cartridge
CN6
Paper-feedmotor
ASFunit
Paper-endsensorCN504CN402
AC
adap
ter
Inksensor
Homepositionsensor
Pick-up rollersensor
Motor control Mechanical control
Inte
rnal
tem
pera
ture
sens
or
+24V DC
Interface control
AC
+5V DC
Control SectionIndicator Control buttonFront cover switch
Indicatorcontrol
Carriage unit
Parallel USB
+3.3V DC
Purge unit
Paper feed/suction driveswitching section
ASF motor
ASF/wiper driveswitching section
Purgesensor
CN5
Figure 3-6 Printer Diagram
CN304 (Parallel Interface Connector)
CN305 (USB Interface Connector)
3-7
BJC-6200 Part 3: Appendix
Ap
pen
dix
Pin No.123456789101112131415161718192021222324252627282930313233343536
Compatible ModeSTROBEDATA1DATA2DATA3DATA4DATA5DATA6DATA7DATA8
ACKNLGBUSYP.E.
SELECTAUTO FEED XT
N.C.GNDGND+5.0V
STROBE-RET (GND)DATA1-RET (GND)DATA2-RET (GND)DATA3-RET (GND)DATA4-RET (GND)DATA5-RET (GND)DATA6-RET (GND)DATA7-RET (GND)DATA8-RET (GND)
ACKNLG-RET (GND)BUSY-RET (GND)P.E.-RET (GND)
INITERROR
GNDN.C
+5.0VSELECT IN
Nibble ModeHostClkData1Data2Data3Data4Data5Data6Data7Data8PrtClk
PrtBusyAckDataReq
XflagHostBusyUndefined
GndGndVcc
Signal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal Gnd
INITDataAvailUndefinedUndefinedUndefined1284Active
ECP ModeHostClkData1Data2Data3Data4Data5Data6Data7Data8
PeriphClkPeriphAck
AckReverseXflag
HostAckUndefined
GndGndVcc
Signal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndSignal GndReverseReqPeriphReqUndefinedUndefinedUndefined1284Active
Pin No.1234
SignalPWR
D-D+
GND
IN/OUTIN
...
FunctionCable power sourceDataDataCable GND
CN401 (Ink Sensor Connector)
CN402 (Pump Sensor Connector)
CN501 (DC Power Source Connector)
CN502 (Carriage Motor Connector)
CN503 (Paper-Feed Motor Connector)
CN504 (ASF Motor Connector)
CN201 (Carriage Ribbon Cable Connector) ↔↔ CN1: Carriage Board
Part 3: Appendix BJC-6200
3-8
Pin No.123
SignalINK_PWM
...INKS
IN/OUTOUT
...IN
FunctionPhoto LED drive signal in the ink sensorGNDVoltage varying according to the reflected light amount
Pin No.123
SignalVSEN
...SNS_DO_RUCK
IN/OUTOUT
...IN
FunctionPhoto LED drive signal in the ink sensorGNDPump sensor sense signal High (sense)/Low
Pin No.1234
Signal+24V
HGND+5-GND
+5V
IN/OUTIN......IN
Function+24VDCGNDGND+5VDC
Pin No.1234
SignalCRACRBCRACRB
IN/OUTOUTOUTOUTOUT
FunctionCarriage motor phase ACarriage motor phase BCarriage motor phase ACarriage motor phase B
Pin No.1234
SignalLFALFBLFALFB
IN/OUTOUTOUTOUTOUT
FunctionPaper-feed motor phase APaper-feed motor phase BPaper-feed motor phase APaper-feed motor phase B
Pin No.1234
SignalASFAASFBASFAASFB
IN/OUTOUTOUTOUTOUT
FunctionPurge (ASF) motor phase APurge (ASF) motor phase BPurge (ASF) motor phase APurge (ASF) motor phase B
Pin No.1~10
11, 12, 1314, 15, 16
17~2627, 28
SignalHVH
SUBH0SUBH1HVH
HVDD
IN/OUTOUTOUTOUTOUTOUT
FunctionHead driving voltage VHSubheater's driving voltage (left side of carriage)Subheater's driving voltage (right side of carriage)Head driving voltage VHLogic driving voltage in the head
CN2 Pin No.19~28
16, 17, 1813, 14, 15
3~121, 2
CN202 (Carriage Ribbon Cable Connector) ↔↔ CN2: Carriage Board
* Details on BENB0 and BENB1
CN203 (Carriage Ribbon Cable Connector) ↔↔ CN3: Carriage Board
3-9
BJC-6200 Part 3: Appendix
Ap
pen
dix
Pin No.1234567891011121314151617181920
21, 22232425262728
SignalDIR
HENB3HENB2HENB1HENB0BENB1*BENB0*EVENODDHALT
HRSTX...
HSEL2B0HSEL2A0HSEL1B0HSEL1A0
...HCLOCK0
...HDATA0
...DIA0DIK0HPA
SNS_HPREGAREGC
IN/OUTOUTOUTOUTOUTOUTOUTOUTOUTOUTOUTOUT
...OUTOUTOUTOUT
...IN/OUT
...IN/OUT
...ININ
OUTIN
OUTIN
FunctionSerial data I/O direction control signalFront heater driving signal for nozzles 113-160 in the headRear heater driving signal for nozzles 113-160 in the headFront heater driving signal for nozzles 1-112 in the headRear heater driving signal for nozzles 1-112 in the headHeater enable decoder's output signal-generation signalHeater enable decoder's output signal-generation signalHeater selection signal for even-numbered nozzles in the head blockHeater selection signal for odd-numbered nozzles in the head blockTiming signal for latching serial dataReset signalGNDFront heater selection for the head block's lower nozzles (9-16, 25-32, ..., 153-160)Rear heater selection for the head block's lower nozzles (9-16, 25-32, ..., 153-160)Front heater selection for the head block's upper nozzles (1-8, 17-24, ..., 145-152)Rear heater selection for the head block's upper nozzles (1-8, 17-24, ..., 145-152)GNDClock signal for transferring the serial data GNDSerial data (left carriage) transferred according to the clock signalGNDHead temperature sensor's (diode) anode in the headHead temperature sensor's (diode) cathodeHome position sensor signal pull-up voltageHome position sense signalDrive voltage to the print position sensor's LEDVoltage varying according to the reflected light amount
CN2 Pin No.282726252423222120191817161514131211109
7, 8654321
BENB0LowHighLowHigh
BENB1LowLowHighHigh
Applicable Nozzles1, 2, 9, 10,..., 153, 154 (1+8n, 2+8n : n=0~19)3, 4, 11, 12,..., 155, 156 (3+8n, 4+8n : n=0~19)5, 6, 13, 14,..., 157, 158 (5+8n, 6+8n : n=0~19)7, 8, 15, 16,..., 159, 160 (7+8n, 8+8n : n=0~19)
Pin No.1234567891011
12, 13, 14151617
18, 19, 20
SignalHSEL2B1HSEL2A1HSEL1B1HSEL1A1
...HCLOCK1
...HDATA1
...HENB5HENB4
...DIA1DIK1
...HVDD
IN/OUTOUTOUTOUTOUT
...IN/OUT
...IN/OUT
...OUTOUT
...ININ...IN
FunctionFront heater selection for the head block's lower nozzles (9-16, 25-32, ..., 153-160)Rear heater selection for the head block's lower nozzles (9-16, 25-32, ..., 153-160)Front heater selection for the head block's upper nozzles (1-8, 17-24, ..., 145-152)Rear heater selection for the head block's upper nozzles (1-8, 17-24, ..., 145-152)GNDClock signal for transferring serial dataGNDSerial data (right carriage) transferred according to the clock signalGNDFront heater driving signal for nozzles 1-160 in the headRear heater driving signal for nozzles 1-160 in the headGNDHead temperature sensor's (diode) anodeHead temperature sensor's (diode) cathodeGNDLogic drive voltage in the head
CN3 Pin No.2019181716151413121110
7, 8, 9654
1, 2, 3
2.1 Carriage Board
CN1 (Carriage Ribbon Cable Connector)See page 3-8 (CN201 Carriage Ribbon Cable Connector).
CN2 (Carriage Ribbon Cable Connector)See page 3-9 (CN202 Carriage Ribbon Cable Connector).
CN3 (Carriage Ribbon Cable Connector)See page 3-9 (CN203 Carriage Ribbon Cable Connector).
CN4/CN5 (Left/Right Cartridge)
CN6 (Print Position Sensor Connector)
Part 3: Appendix BJC-6200
3-10
1 18CN31 27
1 27
CN1
CN2 14
CN
6
1
3
2
4
31
33
34
32
1
3
2
4
31
33
34
32
CN4 CN5
Figure 3-7 Carriage Board
Pin No.1234
SignalREGASNSGREGCLGND
IN/OUTOUT
...OUT
...
FunctionDrive voltage to the print position sensor's LEDGNDVoltage varying according to the reflected light amountGND
Pin No.1~32
33, 34
Signal
...
IN/OUT
...
FunctionSee page 3-11 (BJ Cartridge).
N.C.
2.2 BJ Cartridge
* Details on BENB0 and BENB1
3-11
BJC-6200 Part 3: Appendix
Ap
pen
dix
28 424 20 16 12 8
27 323 19 15 11 7
26 222 18 14 10 6
25 121 17 13 9 5
31
32
30
29
Figure 3-8 BJ Cartridge
BENB0LowHighLowHigh
BENB1LowLowHighHigh
Applicable Nozzles1, 2, 9, 10, ..., 153, 154 (1+8n, 2+8n : n=0~19)3, 4, 11, 12, ..., 155, 156 (3+8n, 4+8n : n=0~19)5, 6, 13, 14, ..., 157, 158 (5+8n, 6+8n : n=0~19)7, 8, 15, 16, ..., 159, 160 (7+8n, 8+8n : n=0~19)
Pin No.1, 2, 34, 6
5, 7, 8, 109
11
1213
14, 1615
17
18
1920212223242526272829303132
SignalHVH
SUBH0/1VHG
HDATA0/1
HSEL1B0/1
HVDDHCLK0/1
GNDHSEL1A0/1
HSEL2A0/1
HSEL2B0/1
HLATODDEVEN
BENB0*BENB1*HENB0/4HENB1/5HENB2/4HENB3/5
DIRHRSTX
DIA0(DIA1)DIK0(DIK1)
...
IN/OUTOUTOUT
...OUT
OUT
OUT
OUTOUT
OUT
OUT
OUTOUTOUTOUTOUTOUTOUTOUTOUTOUTOUTOUTOUT
...
FunctionHead heater driving voltage VH +24 VSubheater's driving voltageHead driving voltage VHGNDSerial data transferred according to the clock signal (H_CLK)Includes head identification information and rank resistanceRear heater selection signal for the head block's upper nozzles (1-8, 17-24, ..., 145-152)Head's logic driving voltage +5 VClock signal for transferring the serial data Head's logic driving voltage HVDD's GNDFront heater selection signal for the head block's upper nozzles(1-8, 17-24, ..., 145-152)Front heater selection signal for the head block's lower nozzles(9-16, 25-32, ..., 153-160)Rear heater selection signal for the head block's lower nozzles (9-16, 25-32, ..., 153-160)Timing signal for latching serial dataHeater selection signal for odd-numbered nozzles in the head blockHeater selection signal for even-numbered nozzles in the head blockHeater enable decoder's output signal-generation signalHeater enable decoder's output signal-generation signalRear heater drive signal for nozzles 1-112 in the headFront heater drive signal for nozzles 1-112 in the headRear heater drive signal for nozzles 113-160 in the headFront heater drive signal for nozzles 113-160 in the headSerial data I/O direction control signalReset signalHead temperature sensor's (diode) anodeHead temperature sensor's (diode) cathodeUnused
2.3 Scanner Cartridge (Optional)
Part 3: Appendix BJC-6200
3-12
28 424 20 16 12 8
27 323 19 15 11 7
26 222 18 14 10 6
25 121 17 13 9 5
31
32
30
29
Figure 3-9 Scanner Cartridge
Pin No.1, 2, 3
456
7, 8910111213141516171819
20, 21, 22232425
26, 27, 2829303132
SignalVHLED
N.C.GNDLED
N.C.GNDLED
DT0GNDLED
RWRVDD
DTCKVSSRENVSSRDT
SCHKRLNSTN.C.DT1DT2DT3N.C.RSTDIADIK...
IN/OUTIN............
IN/OUT...ININ
IN/OUT...IN...INININININININININ
OUTOUT
...
Function+24 V for LEDUnusedGNDUnusedGNDScanned image's serial dataGNDWrite clock for setting the internal resistor+5 VScanned image's serial data clockGNDEnable signal for setting the internal resistorGNDInternal resistor setting dataScanner cartridge detection and recognitionScan start signal (1-line scanning)UnusedFor factory useFor factory useFor factory useUnusedResetScanner cartridge detection and recognitionScanner cartridge detection and recognitionUnused
2.4 AC Adapter
2.5 DC Power
3-13
BJC-6200 Part 3: Appendix
Ap
pen
dix
1 7
2 8
3 5
6
Figure 3-10 AC Adapter
Pin No.12345678
Signal......
+24V...
+5V+5-GND
...HGND
IN/OUT............
OUT.........
FunctionN.C.N.C.+24V DCN.C.+5V DCGNDN.C.GND
3
4
1
5
5
1
Figure 3-11 DC Power Cable
Pin No.12345
Signal+24V
...HGND
+5V-GND+5V
IN/OUTOUT
...
...
...OUT
Function+24V DC
GNDGND+5V DC
2.6 DC Carriage Motor
2.7 Paper Feed Motor
2.8 ASF Motor
Part 3: Appendix BJC-6200
3-14
1
4
Figure 3-12 Carriage Motor
1
4
Figure 3-13 Paper Feed Motor
1
4
Figure 3-14 ASF Motor
Pin No.1234
SignalCRACRBCRACRB
IN/OUTININININ
FunctionCarriage motor phase ACarriage motor phase BCarriage motor phase ACarriage motor phase B
Pin No.1234
SignalLFALFBLFALFB
IN/OUTININININ
FunctionPaper-feed motor phase APaper-feed motor phase BPaper-feed motor phase APaper-feed motor phase B
Pin No.1234
SignalASFAASFBASFAASFB
IN/OUTININININ
FunctionASF motor phase AASF motor phase BASF motor phase AASF motor phase B
2.9 Ink Sensor
2.10 Printing Position Sensor
2.11 Purge Sensor Connector
3-15
BJC-6200 Part 3: Appendix
Ap
pen
dix
13 131 3
Figure 3-15 Ink Sensor
Pin No.123
SignalINK/PWM
...INKS
IN/OUTIN...
OUT
FunctionPhoto LED drive voltage in the ink sensorGNDVoltage varying according to the reflected light amount
1
4
Figure 3-16 Print Position Sensor
Pin No.1234
SignalREGASNSGREGCLGND
IN/OUTOUT
...OUT
...
FunctionDrive voltage to the print position sensor's LEDGNDVoltage varying according to the reflected light amountGND
131 313
Figure 3-17 Purge Sensor
Pin No.123
SignalVSEN
...SNS_DO_RUCK
IN/OUTIN...
OUT
FunctionPhoto LED drive voltage in the ink sensorGNDPump sensor sense signal High (sense)/Low
Part 3: Appendix BJC-6200
3-16
This page intentionally left blank
Ap
pen
dix
BJC-6200 Part 3: Appendix
3-17
8 7 6 5 4 3 2 1
F
E
D
C
B
A
CR BOARD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN1
LGND
HGND
HVH
SUBH1
SUBH0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN2
REGA
HCLOCK0
DIR
HSEL2A0
HRSTX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN3
HVDD
HDATA1
HCLOCK1
HSEL1B1
REGC
HPC
HPA
DIK0
DIA0
SNSG
HSEL2B0
HLAT
HSEL1A0
LGND
ODD
HSEL1B0
EVEN
BENB0
BENB1
HENB0
HENB1
HENB2
HENB3
HDATA0
DIK1
DIA1
SNSG
HENB4
HENB5
LGND
HSEL2A1
HSEL1A1
HSEL2B1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
CN5
C51µF,50V
HSEL1B1
DIR
HSEL1A1
HSEL2B1
HVH
SUBH1
LGND
HLAT
HCLOCK1
HSEL2A1
ODD
EVEN
BENB0
BENB1
HENB4
HENB5
HENB4
HENB5
HDATA1
HRSTX
DIA1
DIK1
HGND
HVDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
CN4
C41µF,50V
HSEL1B0
DIR
HSEL1A0
HSEL2B0
HVH
SUBH0
LGND
HLAT
HCLOCK0
HSEL2A0
ODD
EVEN
BENB0
BENB1
HENB0
HENB1
HENB2
HENB3
HDATA0
HRSTX
DIA0
DIK0
HGND
HVDD
1
2
3
4
CN6
REGA
LGND
REGC
SNSG
C30.1µF,50V
HVDD
LGND SNSG
HPC
HPA
PS1TLP832(CANO)
31
42
2.12 Circuit Diagrams
BJC-6200 Part 3: Appendix
8 7 6 5 4 3 2 1
F
E
D
C
B
A
LOGIC BOARD 01
21
10P,50V
C122
12
0,1A
R122
+3.3R
+3.3R
21
R121
0,1A
PD4
P03
JP3
ROM_A20
12
C120
1U,10V
check
1CP13
3.3V POWER for INSIDE-LOGIC of IC101
FB 21FB104
BK2125HS330
FB1 2
BK2125HS330
FB103
check
1CP133check
1CP134
check
1CP100
+5U
MOT_RESETX
+3.3R
+3.3U
OEX
I/O_8
I/O_7
I/O_6
I/O_5
VCC2
I/O_4
GND3
I/O_16
I/O_15
I/O_14
I/O_13
GND2
I/O_12
I/O_11
I/O_10
I/O_9
NC7
NC6
LCAS
UCAS
OE
A9
A8
I/O_3
A7
A6
A5
A4
GND1VCC3
A3
A2
A1
A0
I/O_2
NC5
NC4
RAS
WE
NC3
NC2
NC1
I/O_1
VCC11
2
11
15
16
17
18
19
20
3
21
22
23
24
25 26
27
28
29
30
4
31
32
33
34
35
36
40
41
42
43
44
45
46
47
48
49
50
5
6
7
8
9
10
MB81V18165B-60PFTN
IC103
1 2
68K,1/16W
R102
21C101
1U,10V
UCASX
LCASX
WEX
RASX0
21
C1041000P,50V
12
C1031U,10V
MD[15:0]
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
MA[9:0]
MA9
MA8
MA7
MA6
MA5
MA4MA3
MA2
MA1
MA0
21C105
1U,10V
12
1000P,50V
C106 2
1C107
1000P,50V
12
C108
1000P,50V
21
1000P,50V
C114
12
C115
1000P,50V
21C116
1000P,50V
12
C109
1U,10V 2
1C117
1U,10V
12
1U,10V
C113
FB
21
FB102BK2125HS330
+3.3V
+5U
+3.3U
+3.3U
+5U
+3.3U
+5U
+3.3U
GND
OUT1OUT23 1
2
CSACW4800MX40001
X101
USB_PW_C
SNS_PW_C
MOT_SET
CVDC_PW_C
VHC_PW_C
check
1CP188
SNS_HP
SNS_PE
SNS_ASF
MOT_ASF1
MOT_ASF0
MOT_ASF6
MOT_ASF2
MOT_ASF3
MOT_ASF4
MOT_ASF5
MOT_ASF[6:0]
MD0
MD1
MD2
MD3
MD4
MD5
MD6
MD7
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MA4
MA5
MA6
MA7
MA8
MA9MA0
MA2
MA3
MA1
EEPROM_D
EEPROM_CS
EEPROM_SK
IF_PW_C
IFD0
IFD1
IFD2
IFD3
IFD4
IFD5
IFD6
IFD7 IFD[7:0]
IFCONT0
IFCONT1
IFCONT2
IFCONT3
IFCONT4
IFCONT5
IFCONT6
IFCONT7
IFCONT8 IFCONT[8:0]
USB_DX
USB_D
ROMD3
ROMD4
ROMD10
ROMD12
ROMD2
ROMD5
ROMD9
ROMD13
ROMD1
ROMD6
ROMD8
ROMD14
ROMD0
ROMD7
ROMD15
ROMD11 ROMD[15:0]
check
1CP80
ROMA1
ROMA15
ROMA2
ROMA[19:0]
ROMA16
ROMA0
ROMA19
ROMA18
ROMA8
ROMA17
ROMA9
ROMA7
ROMA10
ROMA6
ROMA11
ROMA5
ROMA12
ROMA4
ROMA13
ROMA3
ROMA14
SNS_USB
DIODE1
INKS
REGI
THERMO
DIODE0
check
1CP140
LED_POW
LED_RES
POW_SW
RESUME_SW
check
1CP141DOOR
1
3
5
7
2
4
6
8
RA101
10K,0.063 W
+3.3V
RESETX
+5U
208 3.3VDD5
207 5VDD6
206 ST0
205 PC3
204 PC2
203 PC1
202 PC0
201 LF_STB
200 LF_CLK
199 LF_DATA
198 CR_DATA
197 CR_CLK
196 CR_STB
195 PD9
194 PD6
193 PD5
192 PD4
191 PD3
190 PD2
189 PD1
188 BZ
187 SUBH1
186 SUBH0
185 H_D0
184 H_CLK0
183 3.3VDD_INT5
182 GND_INT5
181 HSEL1A0
180 HSEL1B0
179 HSEL2A0
178 HSEL2B0
177 H_RST
176 H_LTH
175 ODD
174 EVEN
173 BENB0
172 BENB1
171 HENB0
170 HENB1
169 HENB2
168 HENB3
167 HENB4
166 HENB5
165 DIR
164 H_D1
163 H_CLK1
162 GND_INT4
161 XT2
160 XT1
159 3.3VDD_INT4
158 5VDD5
157 3.3VDD4
156
GND9
155
GND8
154
5VDD4
153
HSEL1A1
152
HSEL1B1
151
HSEL2A1
150
HSEL2B1
149
P00/INTP100
148
P04/PWM0
147
P05/PWM1
146
P01/INTP101
145
P02/INTP102
144
P03/INTP103
143
PA0
142
PA1
141
P17/RXD
140
P16/TXD
139
GND_INT3
138
3.3VDD_INT3
137
RESETX
136
AVSS_AVREFM
135
AVSS
134
ANI7
133
ANI6
132
ANI4
131
ANI5
130
ANI2
129
ANI3
128
ANI1
127
ANI0
126
AVDD
125
AVREF_AVREFP
124
ROM_A19
123
ROM_A18
122
ROM_A8
121
ROM_A17
120
ROM_A9
119
ROM_A7
118
ROM_A10
117
ROM_A6
116
ROM_A11
115
ROM_A5
114
ROM_A12
113
ROM_A4
112
ROM_A13
111
ROM_A3
110
ROM_A14
109
ROM_A2
108
ROM_A15
107
ROM_A1
106
GND7
105
GND6
1043.3VDD3
1035VDD3
102ROM_A16
101ROM_A0
100ROM_A20
99CS0X
98ROM_D15
97ROM_D7
96ROM_D0
95ROM_D14
94ROM_D8
93ROM_D6
92ROM_D1
91ROM_D13
90ROM_D9
89ROM_D5
88ROM_D2
87ROM_D12
86ROM_D10
85ROM_D4
84ROM_D3
83ROM_D11
82PD0
81NTEST2
80NTEST1/TST7
79GND_INT2
783.3VDD_INT2
77GND5
76USB_DX
75USB_D
74STB
73IF_D0
72IF_D1
71IF_D2
70IF_D3
69IF_D4
68IF_D5
67IF_D6
66IF_D7
65ACK
64BUSY
63PE
62SLCT
61FAULT
60AFXT/SCK
59INIT
585VDD2
57SELIN
56AMC
55PB0
545VDD1
533.3VDD2
52GND4
51GND3
50PB1
49PB2
48PB3
47RAM_A4
46RAM_A5
45RAM_A6
44RAM_A7
43RAM_A8
42RAM_A9
41OEX
40UCASX
39LCASX
38RAM_D8
37RAM_D9
36RAM_D10
35RAM_D11
34RAM_D12
33RAM_D13
32RAM_D14
31RAM_D15
30RAM_A3
29RAM_A2
28RAM_A1
273.3VDD_INT1
26GND_INT1
25RAM_A0
24RASX1
23RASX0
22WEX
21RAM_D7
20RAM_D6
19RAM_D5
18RAM_D4
17RAM_D3
16RAM_D2
15RAM_D1
14RAM_D0
13ST7/TST6
12ST6/TST5
11ST5/TST4
10ST4/TST3
9ST3
8TST1
7ST2/SOT
6ITEST/SIN
5SMC
4ST1/TST2
33.3VDD1
2GND2
1GND1
1 2 3 4 5 6 7 8 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
IC101
+5U
+5V+5U
+3.3V+3.3U
+3.3R
5V POWER for PORT of IC101
3.3V POWER for OUTSIDE-PORT of IC101
MOT_CR_LF5
MOT_CR_LF4
MOT_CR_LF3
MOT_CR_LF2
MOT_CR_LF1
MOT_CR_LF0
MOT_CR_LF[5:0]
check
1CP24
HEADCONT21
HEADCONT12
HEADCONT3
HEADCONT24
HEADCONT25
HEADCONT26
HEADCONT1
HEADCONT0
HEADCONT2
HEADCONT11
HEADCONT10
HEADCONT9
HEADCONT8
HEADCONT7
HEADCONT6
HEADCONT5
HEADCONT4
HEADCONT20
HEADCONT19
HEADCONT18
HEADCONT17
HEADCONT16
HEADCONT15
HEADCONT14
HEADCONT[26:0]
HEADCONT22
HEADCONT23
HEADCONT13
SNS_DO_RUCK
INK_PWM
+5U +3.3U
FB 21
FB106
BK1608HS121
CS0X
12
C102
1000P,50V/NOTMNT
21
0.1U,25V
C130
+3.3V
FB
12
FB101
VV1-2000000
+3.3R
ST7
BZ
RASX1
check
1CP144
JP2
P16
P17
NTEST1
check
1CP194
check
1CP192
PD6
REG_PW_C
1 2
0,1A
R101
FB1 2
BK2125HS330
FB105
A0
A1
A2
A3
A4
A5
N.C
A8
A6
A9
A10
A11
A12
A13
A14
A15
A16
_BYTE/VPP
GND2
D15/A1-1
D7
D14
D6
D13
D5
D12
D4
VDDD11
A7
D3
D10
D2
D9
D1
D8
D0
OE
GND1
CE
A17
A181
2
11
12
13
14
15
16
17
18
19
20
3
21 22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
4
41
42
5
6
7
8
9
10
DILB42P-8J
IC102
ROMD15
ROMD14
ROMD13
ROMD12
ROMD11
ROMD10
ROMD9
ROMD8
ROMD7
ROMD6
ROMD5
ROMD4ROMD3
ROMD2
ROMD1
ROMD0
ROMD[15:0]
ROMA0
ROMA16
ROMA15
ROMA14
ROMA13
ROMA12
ROMA11
ROMA10
ROMA9
ROMA8
ROMA19ROMA18
ROMA17
ROMA7
ROMA6
ROMA5
ROMA4
ROMA3
ROMA2
ROMA1
ROMA[19:0]
1 2
150,1/16W
R105
FB 21
BK1608HS121
FB107
12
C131
10P,50V/NOTMNT
21
C133
10P,50V/NOTMNT
21
3.3K,1/16W
R103
+3.3R
12
C121
1000P,50V
12
C124
1U,10V
12
R120
10,1/16W
+3.3R
21
R123
0,1A
21
C123
1U,10V
CS0X
C131:
C133:
<01-D1>
<01-F1>
<02-A8,F5>
<05-F6>
<04-C6><05-E2><04-B6>
<02-B8>
<05-D1>
<05-E1><02-D8><04-D8><04-B8><04-A8>
<05-C6>
<04
-D3>
<04
-D3>
<04
-D1>
<04
-F8>
<02
-C8>
<04
-F3>
<04
-F8>
<04
-F8>
<04
-E8>
<04
-E8>
<03
-D8>
<02
-F8>
<04
-E3>
<02
-C8>
<04
-E6>
<02
-E8>
<01-E6>
<01-D8>
<01-E6><03-D8>
<03-C8><03-C8>
<03-F5>
<03-E6>
<04-D6>
<01-E1>
3-18
Ap
pen
dix
BJC-6200 Part 3: Appendix
8 7 6 5 4 3 2 1
F
E
D
C
B
A
LOGIC BOARD 02
+5V
+5V +5V
+5V+5V
LOGIC_GNDLOGIC_GND
+5V
+5V
+5V
HVH
12
0.01U,50V
C203
SUBH1
SUBH0
21
R24310K,1/16W
4
2
1
3 6
8
7
5
Q205
TPC8201
12
R242100,1/16W
21
R240100,1/16W
12
R24110K,1/16W
HLAT
HDATA0
HCLOCK0
HSEL1A0
HSEL1B0
HSEL2A0
HSEL2B0
HRSTX
ODD
EVEN
BENB0
BENB1
HENB0
HENB1
HENB2
HENB3
HENB4
HENB5
HDATA1
HCLOCK1
HSEL1A1
HSEL1B1
HSEL2A1
HSEL2B1
21R23533,1/16W
4
21
3
5 6
7 8
FB205BK32164S601
87
65
3
1 2
4
BK32164S601FB209
3
21
FB201FK2125T256AL
1 2
3
FB202FK2125T256AL 1 2
3
FB207FK2125T256AL
3
21
FB208FK2125T256AL
87
65
3
1 2
4
BK32164S601FB204
HVDD
DIA0
J20P
20 CN203J20P
19 CN203J20P
18 CN203J20P
17 CN203J20P
16 CN203J20P
15 CN203J20P
14 CN203J20P
13 CN203J20P
12 CN203J20P
11 CN203J20P
10 CN203J20P
9 CN203J20P
8 CN203J20P
7 CN203J20P
6 CN203J20P
5 CN203J20P
4 CN203J20P
3 CN203J20P
2 CN203
J28P
28 CN202J28P
27 CN202J28P
26 CN202J28P
25 CN202J28P
24 CN202J28P
23 CN202J28P
22 CN202J28P
21 CN202J28P
20 CN202J28P
19 CN202J28P
18 CN202J28P
17 CN202J28P
16 CN202J28P
15 CN202J28P
14 CN202J28P
13 CN202J28P
12 CN202J28P
11 CN202J28P
10 CN202J28P
9 CN202J28P
8 CN202
J28P
6 CN202J28P
5 CN202J28P
4 CN202J28P
3 CN202J28P
2 CN202
J28P
28 CN201J28P
27 CN201J28P
26 CN201J28P
25 CN201J28P
24 CN201J28P
23 CN201J28P
22 CN201J28P
21 CN201J28P
20 CN201J28P
19 CN201J28P
18 CN201J28P
17 CN201J28P
16 CN201J28P
15 CN201J28P
14 CN201J28P
13 CN201J28P
12 CN201J28P
11 CN201J28P
10 CN201J28P
9 CN201J28P
8 CN201J28P
7 CN201J28P
6 CN201J28P
5 CN201J28P
4 CN201J28P
3 CN201
SUBH1
SUBH0
100K
100K 100
33K 7.5K
1K
DIK0
DIK1
1K
7.5K180K
180K
12K33K
12K
100100K
100K
1 2
390K,1/16W
R201
11
4
7
5
6
IC201LA6324NML
21
390K,1/16W
R251
9
10
8
411
IC201LA6324NML
4 5
RA201
8 1
RA201
27
RA20163
RA201
7 2
RA202
3 6RA202
18
RA202
5 4
RA202
1 8
RA204
5 4
RA204
72RA204
36
RA204
2 7
RA203
4 5RA203
6 3
RA203
81
RA203
HENB3
HENB0
HLAT
HSEL1B0
HDATA0
HVH
REGA
DIA11
3
2
5
4
NNCD6.8G
ZD210
12
C2600.1U,25V
1
3
2
5
4
NNCD6.8G
ZD208
+24V
HPA1 2
R210
220,1/8W
21
22K,1/16W
R211
VSEN
SUBH0
1
3
2
5
4
NNCD6.8G
ZD202
4
5
2
3
1
ZD203
NNCD6.8G
1
3
2
5
4
NNCD6.8G
ZD204
4
5
2
3
1
ZD205
NNCD6.8G
1
3
2
5
4
NNCD6.8G
ZD206
4
5
2
3
1
ZD207
NNCD6.8G
HSEL2A0
4
5
2
3
1
ZD201
NNCD27G
SUBH1
HVH
HENB2 HENB3
BENB0
HRSTX
ODD
HSEL1A0
HCLOCK0
HPA
HSEL2A1 HSEL2B1
HSEL1A1
HDATA1
HDATA0
REGC SNS_HP
HSEL1B1
REGA
HSEL2B0
HCLOCK1
HSEL1B0
HLAT
HENB1 DIR
BENB1
EVEN
HENB5 HENB4
DIK0
12
3 RN2415
Q203
+24V
21
C2021000P,50V
1 2
220,1/8W
R262
21
R2601K,1/16W
REGI REGC
+5V
+3.3V
4
5
2
3
1
NNCD6.8G
ZD209
DIK1
4
2
1
3 6
8
7
5
Q204
TPC8402
11
4
14
12
13
IC201LA6324NML
2
3
1
411
IC201LA6324NML
J28P
1 CN201
J28P
2 CN201J28P
1 CN202
J28P
7 CN202
J20P
1 CN203
DIR
HENB2
HENB1
BENB0
BENB1
ODD
EVEN
HRSTX
HSEL2B0
HSEL2A0
HSEL1A0
HCLOCK0
DIK0
HPA
SNS_HPREGA
REGC
HSEL2B1
HSEL2A1
HSEL1B1
HSEL1A1
HCLOCK1
HDATA1
HENB5
HENB4
DIA1
DIK1
21
10K,1/16W
R213
21
R21610K,1/16W
12
10K,1/16W
R215
12
100K,1/16WR221
1 2
100,1/16W
R214
DIA1
DIA0
SNS_HP SNS_HP
VHC_PW_C
HEADCONT22
HEADCONT[26:0]
HEADCONT2
21
0.1U,25VC201
+5V
H_GND CN202-22pin:SENSOR_GND
4
21
3
5 6
7 8
BK32164S601FB203
HEADCONT19
HEADCONT26
HEADCONT25
HEADCONT24
HEADCONT23
HEADCONT21
HEADCONT20
HEADCONT[26:0]
HEADCONT0
HEADCONT1
HEADCONT5
HEADCONT6
HEADCONT8
HEADCONT9
HEADCONT10
HEADCONT11
HEADCONT12
HEADCONT13
HEADCONT14
HEADCONT15
HEADCONT16
HEADCONT17
HEADCONT18
HEADCONT7
HEADCONT4
HEADCONT3
DIR87
65
3
1 2
4
FB206BK32164S601
HENB0
DIA0
HVDD
DIODE0
DIODE1
REG_PW_C
12
5.1K,1/16WR261
21
47K,1/16WR263
<01-F3>
<01-F3>
<04-C4>
<01-C5>
<01-F3>
<01-F4>
<01-C5>
<01-F6>
<02-C4,D5>
<02-C4,D6>
<02-C4,D5>
<02-B3,B5>
<02-B3,B6>
<02-B3,B5>
<02-B3,B6>
<02-B3,B6>
<02-B3,B5>
<02-A6,B1>
<02-A5,B1><01-F6>
<02-A6,C4>
<02-C3,E3>
<02-C3,E3>
<02-C3,E3>
<02-C3,E3>
<02-C3,F3>
<02-C3,F3>
<02-C3,F3>
<02-B3,F3>
<02-B3,E6>
<02-B3,D6>
<02-B3,C6>
<02-C1,F1>
<02-C1,F1>
<02-C1,F1>
<02-B1,E3>
<02-B1,F6>
<02-B1>
<02-C1,F1>
<02-B1,E3>
<02-B1,F6>
<02-C1,F1>
<02-C1,F1>
<02-B3,C6>
<02-B3,D6>
<02-B3,E6>
<02-B3,F3>
<02-C3,F3>
<02-C3,F3>
<02-C3,F3>
<02-C3,F3>
<02-C3,E3>
<02-C3,E3>
<02-C3,E3>
<02-C3,E3>
<02-B6,C4>
<02-A6,C4>
<02-B6,D5>
<02-A6,D5>
<02-A6,D6>
LOGIC_GND
<02-D5,E3><02-D5,E3><02-D6,E3><02-D6,E3><02-C5,E3><02-C5,E3><02-C6,E3><02-C6,E3><02-C5,F3><02-C5,F3><02-C6,F3>
<02-C6,F3><02-C5,F3><02-C5,F3><02-C6,F3>
<02-C6,F3>
<02-B5,F3>
<02-B5,E6><02-B6,E6><02-B6,D6><02-B5,D6><02-B5,C6><02-B6,C6>
<02-B5,F1><02-B6,F1><02-B6,F1><02-B5,F1>
<02-A5,F1>
<02-A6,F1>
<02-A6,E3><02-A5,E3>
<02-A5,F6><02-A6,F6>
<02-A6>
<02-B3,B5><02-B3,C6><02-C3,C6><02-C3,C5><02-C3,C5><02-C3,C6><02-C3,C6><02-C3,C5><02-C3,C5><02-C3,C6><02-C3,C6><02-C3,C5><02-C3,C5><02-C3,D6><02-C3,D6><02-C3,D5><02-A5,B1><02-A6,B1><02-C3,D5>
<02-A6,C1><02-A5,C1><02-B5,C1><02-B6,C1><02-B6,C1><02-B5,C1>
<02-F5>
<02-A8>
<04-B4>
<04-B4>
3-19
Ap
pen
dix
BJC-6200 Part 3: Appendix
8 7 6 5 4 3 2 1
F
E
D
C
B
A
LOGIC BOARD 03
SYMBOL = RCA4E2
12
3
4
5
6
7
8
9
10
CA302
NFA3216G2C100R6R8
4
3
51 2
RA307
3.3K,0.063W
1
3
5
7
2
4
6
8
RA3050.10A,FERRITE
VUSB
Gnd
D+
D-
PWR
+3.3V
12
3
Q301RN2415
12
R340
33K,1/16W
J4P
4CN305J4P
3CN305J4P
2CN305J4P
1CN305
45
2 31
FTZ6.8E/NOTMNT
ZD305
21
R339
22K,1/16W
21 24,1/16WR342
1 2
24,1/16WR343
12
R33847K,1/16W
21
R3411.5K,1/16W
E
1
2
3
E001
FAULT
SLCT
PE
BUSY
ACK
SELIN
INIT
AFXT
D1J36P
2 CN304
J36P
3 CN304
J36P
4 CN304
J36P
5 CN304
J36P
6 CN304
J36P
7 CN304
J36P
8 CN304
VIF
8
6
4
2
7
5
3
1
RA3010.10A,FERRITE
IFD[7:0]
IFD7
IFD6
IFD5
IFD4
IFD3
IFD2
IFD1
IFD0
J36P
9 CN304
1 2R324 1K,1/16W
21
10,1/16WR318
21
10P,50VC311
12
C31210P,50V
12
C31310P,50V
21
C314470P,50V
12
C31510P,50V
21
C31610P,50V
21
C31710P,50V
12
470P,50VC320
12
10P,50VC319
1 2
100,1/16WR317
IFCONT[8:0]
IFCONT8
IFCONT7
IFCONT6
IFCONT5
IFCONT4
IFCONT3
IFCONT2
IFCONT1
IFCONT0
D2
D3
D4
D5
D6
D7
D8
STBJ36P
1 CN304
J36P
14 CN304
J36P
31 CN304
J36P
10 CN304
J36P
11 CN304
J36P
12 CN304
J36P
13 CN304
J36P
32 CN304
J36P
15 CN304
J36P
16 CN304
J36P
17 CN304
J36P
18 CN304
J36P
19 CN304
J36P
20 CN304
J36P
21 CN304
J36P
22 CN304
J36P
23 CN304
J36P
24 CN304
J36P
25 CN304
J36P
26 CN304
J36P
27 CN304
J36P
28 CN304
J36P
29 CN304
J36P
30 CN304
J36P
33 CN304
J36P
34 CN304
J36P
35 CN304
2
1
5
3
4
RA3033.3K,0.063W
4
21
3
5 6
7 8
FB302BK32164S471
J36P
36 CN304
SNS_USB
USB_PW_C
USB_DX
USB_D
8
6
4
2
7
5
3
1
RA309 1K,0.063 W
87
65
3
1 2
4
BK32164S471FB303
1
3
5
7
2
4
6
8
RA3020.10A,FERRITE
21
R316100,1/16W
12
R323
1K,1/16W
8642
7531
1K,0.063 W
RA306
21
R319
390,1/8W
4
3
5
1
2
3.3K,0.063WRA304
87
65
3
1 2
4
FB312BK32164S601
4
21
3
5 6
7 8FB311BK32164S601
21 5
3
4
RA308
3.3K,0.063W
6
4
5
1
2
3
617CM1427
CF301
10
9
8
7
6
5
4
3
21
CA301
NFA3216G2C100R6R8
<01-F3>
<01-D1>
<01-D1><01-D1>
<01-C1>
<01-C1>
<04-D4>
3-20
Ap
pen
dix
BJC-6200 Part 3: Appendix
8 7 6 5 4 3 2 1
F
E
D
C
B
A
LOGIC BOARD 04
DOOR
RESUME_SW
POW_SW
12
100P,50V
C4032
1100P,50V
C402
J3P
3CN402
J3P
2CN402
21
100P,50VC431
12
R435390,1/16W
21
R43439K,1/16W
EEPROM_CS
12
R43139K,1/16W
21
R432390,1/16W
2 4
1 3
TLP832(CANO)PS402
12
100P,50VC430
+3.3V
+3.3V
21
3.3K,1/16W
R425
21
0.1U,25VC410
1 2
R414
1K,1/16W
12
3
FP1L3NQ404
J3P
2 CN401
+5V
+5V
1 2
47K,0.063W
R407
RESUME(ORANGE)
POWER(GREEN)
+5V
LED_RES
SKHVLH
SKQNLA
DOOR
RESUME
POWER1 2SW401SKQNLA
21
SKQNLA
SW402
1 2
SKHVLH
SW403
LED_POW1 2
R401
180,1/10W
21
180,1/10W
R402
31
42
PS401TLP831(CANO)
12
390,1/16WR405
21
39K,1/16WR404
21
TBPS1473J475H5Q
TH401
2 1
0.01U,50V
C408
12
3 Q401RN2415
21
R40847K,1/16W
FB 21FB403
BK1608HS601
3
21
RN2415Q402
+5V
12
47K,1/16WR409
12
3FP1L3NQ403
21
R41047K,1/16W
J3P
1 CN401
J3P
3 CN401INKS
21
150,1/4W
R413
12
68K,1/16W
R412
+5V
NC TEST
VCC GND
CS DO
SK DI54
63
72
81
S-93C56AFJ-TF
IC402
21
0.1U,25VC411
+5V
21
SEC2494C
LED401
3 4
SEC2494C
LED401
SKQNLA
FB
21FB402
BK1608HS601
FB 12
FB406BK1608HS121
FB2 1
FB405BK1608HS121
SNS_ASF
SNS_PE
THERMO
IF_PW_C
SNS_PW_C
VSEN
VIF
INK_PWM
EEPROM_D
EEPROM_SK
J3P
1CN402
SNS_DO_RUCK
21
100P,50VC404
12
C401
100P,50V
FB 12
FB404BK1608HS121
CVDC_PW_C
HVDD
FB
12
BK1608HS601
FB408
FB2 1
BK1608HS601
FB407
<01-F4>
<01-F4>
<01-F4>
<01-F4>
<01-F4>
<01-C5>
<01-C5>
<01-B5>
<01-F3>
<01-B1>
<01-C5>
<01-C5>
<02-A6,B1>
<02-D8>
<03-F3>
<01-F4>
<01-F3>
<01-B2><01-B2>
<01-B2>
3-21
Ap
pen
dix
BJC-6200 Part 3: Appendix
8 7 6 5 4 3 2 1
F
E
D
C
B
A
LOGIC BOARD 05
21
R531
0,1A
21
1000P,50V
C531
RESETX
+5V
J4P
4CN501
J4P
3CN501
J4P
2CN501
24V for MTD2002G
24V for TB62201F
J4P
1CN504
3
21 Q501
FA1L4M
21
RD3.3SB2
ZD505
12
390,1/16W
R522
21R521
22K,1/16W
24VCC2
23IN1
22IN2
21I0
20VSA
19VR
25GND2
18CR
17VSB
16STB
15I1
14IN3
13IN412 VCC1
11 OUT4
10 NC3
9 VMMB
8 RSB
7 OUT3
26 GND1
6 OUT2
5 RSA
4 VMMA
3 NC2
2 OUT1
1 NC11
2
3
4
5
6
26
7
8
9
10
11
12 13
14
15
16
17
18
25
19
20
21
22
23
24
IC503
MTD2002G
21
0.51,1/4W
R519
12
0.51,1/4W
R517
J4P
2CN504
J4P
3CN504
J4P
4CN504
+5V
+5V+24R
21
C5190.01U,50V
12 C520
0.01U,50V
12
R505100K,1/16W
*4
FB1 2FB523FB1 2FB522FB1 2FB521
CRB*
CRA*
CRB
CRA
LFB*
LFA*
LFB
LFA
J4P
4CN503J4P
3CN503J4P
2CN503J4P
1CN503
J4P
4CN502J4P
3CN502J4P
2CN502
+24U
+5V
+24U
+5V+5V
21C518
0.1U,25V
21
22K,1/16W/NOTMNT
R507
12
C5100.01U,50V
+24U
+24V
21
C501100U,35V
+24V
HGND
+5V-GND
+5V
+5V
12
R50312K,1/10W
21
R504100K,1/16W
VSS1
VREF_AB
CR_AB
CCP_A
NC
OUT_B-
PGND1
VMA
OUT_A-
RS_A
PGND4
OUT_A
STROBE_AB-
CLK_AB
DATA_AB
RESET
VSS2
VDD
DATA_CD
CLK_CD
STROBE_CD-
OUT_C
PGND3
RS_C
OUT_C-
RS_B
VMCVMD
OUT_D
RS_D
PGND2
OUT_D-
CCP_C
CCP_B
CR_CD
VREF_CD
OUT_B
VMB1
2
10
11
12
13
14
15
16
17
18 19
3
20
21
22
23
24
25
26
27
38
28
29
30
31
32
33
34
35
36
4
5
6
7
8
9
37
TB62201AF
IC401
+24U
1 2
R5090.75,1/4W
+24U
12
R508
390,1/16W
12
680P,50V/NOTMNT
C5172
11000P,50V
C516
12
2K,1/16W
R506
2 1C508
0.22U,50V
12
C5090.015U,50V
21
0.75,1/4WR511
1 2
R5150.75,1/4W
J4P
1CN502
+24U
21
C512
100P,50V
12100P,50V
C513
21
C514
100P,50V
12
C515
100P,50V
4
5
2
3
1
NNCD27G/NOTMNT
ZD501
FB 21
FBMH2016HM251N
FB520
+24R
24V for BJ-HEAD
J4P
1CN501
8CD
7GND
6N.C
5VOUT4 VIN
3 CONT
2 RESETX
1 N.C.1
2
3
4 5
6
7
8
MM1478FFBE
IC501
MOT_RESETX
MOT_CR_LF4
MOT_CR_LF3
MOT_CR_LF2
MOT_CR_LF1
MOT_CR_LF0
MOT_CR_LF5
MOT_CR_LF[5:0]
12
C521
3300P,50V
+5V
MOT_ASF6
MOT_ASF2
MOT_ASF5
MOT_ASF4
MOT_ASF1
MOT_ASF0
MOT_ASF3
MOT_ASF[6:0]
21
0.75,1/4WR513
12
ZD504RD2.7SB1
21
ZD503
RD2.7SB1
ASFA
ASFB
ASFA*
ASFB*
MOT_SET
21
0.01U,50VC511
12
D1FS4A
D501
21
C505220U,35V
12C506
220U,35V
FB
21
FBMH3216HM501NT
FB502
1 2
FU501FCC3220202
21
FU502FCC3220202
FB1 2
FB501
FBMH3216HM501NT
FB 21
FB503
FBMH3216HM501NT1
2
1000U,35V
C504
21 1U,10V
C502
12
C507
1000P,50V
12
1000P,50V
C530
12
R530
0,1A
21
R502
1K,1/16W 2
1
47U,35VC503
+3.3V
by IC501 by FB102(IC103)<01-F6>
<01-B6>
<01-C5>
<01-C6>
<01-C6>
3-22
Ap
pen
dix
PRINTED IN JAPAN (IMPRIME AU JAPON) CANON INC.
The printing paper contains100% waste paper.