M.A - TE-MPE TM - 3rd of April 2014

BIS Application @Linac4 and outlook for post LS1

Maxime AudrainTE-MPE TM, 2014-04-03

On behalf of the TE-MPE-MS Software Team:D. Anderson, M. Dragu, K. Fuchsberger, J.-C. Garnier, A. Gorzawski,

M. Koza, K.H. Krol, A. Moscatelli, K.Stamos, P.C. Turcu

2

Content

Status of BIS in operation during LS1

BIS software for the restart

Wishes and Vision

Summary

3

Architecture overview

M.A - TE-MPE TM - 3rd of April 2014

4

Introduction

BIS hardware changes involve a follow-up on the software side. RIO3 not supported by CO, running out of spares, Migration to MEN A20 controller involves defining a new driver

for the communication from the FESA classes to the board registers.

At the same time, provide monitoring for new hardware and operational deployments during LS1.

Focusing on clean-up and unification during LS1 to ensure increased maintainability until BIS2 is specified.

M.A - TE-MPE TM - 3rd of April 2014

5

Status of BIS in operation during LS1

Status of BIS in operation during LS1

BIS software for the restart

Wishes and Vision

Summary

6

BIS@LN4, Hardware status

M.A - TE-MPE TM - 3rd of April 2014

Courtesy: Bruno Puccio

Already installed

To be installed E.T.A End of April

7

BIS@LN4, Driver

Encore 2 (DriverGen3 version 2) driver deployed :

M.A - TE-MPE TM - 3rd of April 2014

Pros : generate the driver from the Hardware type defined in the CCDB,

Cons : no versioning (one hardware definition per driver type).

8

BIS@LN4, FESA

Old “Bic” FESA class is deprecated: Unused properties, deprecated functionalities (old History

Buffer), lot of redundancies,

“New” (since 2011) CIB FESA class in version 2.10 Initially defined for the new deployments with Linux controller

in the LN4 and PSB, Reduced number of properties -> easier to maintain, Validated during the last 3 years, “Generic” -> support specificities from board types

(CIBM/CIBX/CIBDS boards handled by one FESA class).

M.A - TE-MPE TM - 3rd of April 2014

9

BIS@LN4, GUIs – BIS supervisor

Refactored version of the old LHC/SPS/TL BIS supervisor,

Cleaned, no deprecated functionalities, expert oriented,

But not adapted for cyclic machines (LN4, PSB, TL, SPS).

M.A - TE-MPE TM - 3rd of April 2014

10

BIS@LN4, GUIs – Cycle BIS GUI

A generic monitoring GUI for cyclic machines,

Plot per cycle/per channel, with time markers,

Filtering per masked, disabled and interlocking inputs (more will come).

M.A - TE-MPE TM - 3rd of April 2014

11

CIBDS, Hardware status

Additional asynchronous beam dump trigger to the LBDS,

First version in the LAB, will be installed in point 6 for LBDS reliability dry-run (April).

M.A - TE-MPE TM - 3rd of April 2014Courtesy: Stéphane Gabourin

More info

12

CIBDS, Driver / FESA / GUI

Hardware type defined in the CCDB: Driver generated, deployed and running in the LAB, Follow-up HW deployment in point 6 (April),

CIB FESA class modified to allow communication with the CIBDS board: Added a board type that links to a driver type and

enable/disable properties depending on this board type.

GUI to be defined at a later stage.

M.A - TE-MPE TM - 3rd of April 2014

13

Summary of the current status

3 Driver types: CIBM -> handles CIBM/CIBX boards CIBG, CIBDS -> CIBG/CIBDS boards

2 FESA classes: CIB -> handles CIBM/CIBX/CIBDS boards CIBG -> handles CIBG board

2 GUIs for Linac 4 and PSB: BIS supervisor Cycle BIS GUI

M.A - TE-MPE TM - 3rd of April 2014

14

BIS software for the restart

Status of BIS in operation during LS1

BIS software for the restart

Wishes and Vision

Summary

15

Priorities qualification

mandatory for BIS operation after LS1,

highly recommended for BIS operation after LS1,

Can reuse/recycle functionality from previous/other GUIs!

Functionality already provided!

M.A - TE-MPE TM - 3rd of April 2014

16

Hardware changes

LynxOS to Linux migration: Change 33 FEC controllers, Reprogram VME interface on 58 CIBM/X & 7 CIBG.

Installation: SPS in April, Transfer lines and LHC this summer.

M.A - TE-MPE TM - 3rd of April 2014

17

Drivers

Regenerate CIBG driver using new driver version (Encore 2),

Deploy the 3 driver types on all related FECs.

M.A - TE-MPE TM - 3rd of April 2014

18

FESA

CIB FESA class will stay with version 2.10. Reuse PM property to allow PM data push in case of PM trigger, Inform users of class change (LHC Sequence, SIS).

CIBG FESA class (2.10) to adapt to a Linux controller: Plug the class to the Encore driver, Failing rearm issue (delay between A and B loops) to be followed

with Verena, Will be done in the following weeks to be ready for the LBDS

reliability run.

Deploy the 2 classes types on all related FECs.

M.A - TE-MPE TM - 3rd of April 2014

19

BIS GUI - harmonization

Merge functionalities from our current BIS applications into one central application: The minimum: harmonized and

cleaned application, BIS monitor functionalities to be

merged (follow-up with Jorg), Other non BIS related

functionalities to be moved to Fabio Follin application.

M.A - TE-MPE TM - 3rd of April 2014

20

BIS GUI – main tasks

Define more filters for device monitoring (per accelerator, beam, location, etc…)

Statuses : list of current interlocks, hidden interlocks and masks

Commands : executing any command on 1..N BICs

M.A - TE-MPE TM - 3rd of April 2014

21

BIS GUI prototype - overview

M.A - TE-MPE TM - 3rd of April 2014

22

BIS GUI prototype – cyclic monitor

M.A - TE-MPE TM - 3rd of April 2014

23

BIS GUI prototype – static monitor

M.A - TE-MPE TM - 3rd of April 2014

24

BIS GUI prototype – statuses

M.A - TE-MPE TM - 3rd of April 2014

25

BIS GUI prototype – commands

M.A - TE-MPE TM - 3rd of April 2014

26

Pre-Current-Post operational checks

DIAMON checks have to be defined ASAP! No control on the implementation of the checks (we only

provide specifications), pros are no additional software to maintain, cons are that it might need several iterations to make it right,

Set communication between hardware guys and DIAMON guys.

Pre-operational checks (sequencer) needs to be reviewed and adapted to the change of the FESA class,

Post-operational checks (PM modules) : same hardware as pre-LS1, same PM Buffers, only need to commission the analysis modules.M.A - TE-MPE TM - 3rd of April 2014

27

Wishes and Vision

Status of BIS in operation during LS1

BIS software for the restart

Wishes and Vision

Summary

28

Wishes !

Operators wishes : Input masked by who, when and why! Information on how to resolve in case of an interlock

(application link, procedure, etc…),

Use the analysis language to perform pre-operational checks,

A common server for SMP and BIS Providing information for all applications at CERN (Beam

permit flag, decoding information, etc…).

M.A - TE-MPE TM - 3rd of April 2014

29

Vision – Board specifications

A single source for board specifications: Providing information on board and registers, how to decode

them and which commands can be performed.

M.A - TE-MPE TM - 3rd of April 2014

Register decoding module (JAVA)

30

Vision - FESA

Abstract our FESA classes to avoid code duplication: Might be provided by FESA3 after the LS1

M.A - TE-MPE TM - 3rd of April 2014

31

Summary

Status of BIS in operation during LS1

BIS software for the restart

Wishes and Vision

Summary

32

Main tasks

Deploy drivers and FESA classes, Add PM property, inform users of class changes,

BIS GUI available for all accelerators and all roles, Add statuses and commands panels,

DIAMON checks specification have to be defined ASAP!

Pre-operational checks to be adapted to the new FESA class.

M.A - TE-MPE TM - 3rd of April 2014

33

Planning

3 sprints starting from the 23rd of April until the 19th of June -> BIS software layers ready for SPS ring commissioning,

A few sprints depending on priorities for Transfer lines and LHC integration in the application,

Probably not many more dedicated sprints before the restart : time has to be shared with other projects.

M.A - TE-MPE TM - 3rd of April 2014

34

Thank you for your attention

Do you have any questions?

M.A - TE-MPE TM - 3rd of April 2014