Post on 03-Jun-2018
8/12/2019 backbone safety tips
1/50
BACK AND LIFTING SAFETY
8/12/2019 backbone safety tips
2/50
LIFTING HAZARDS AND SOME IDEAS
ON HOW TO REDUCE YOUR RISK OF
LIFTING INJURY
BACK AND LIFTING SAFETY
8/12/2019 backbone safety tips
3/50
BY THE END OF THIS SLIDESHOW YOU WILLBE ABLE TO:
Identify the types of lifting that may cause
injuries
Review ergonomics principles used in
reducing lifting hazards and preventing
injuries
Contact L&I resources for assistance
BACK AND LIFTING SAFETY
8/12/2019 backbone safety tips
4/50
STATISTICS ON LIFTING INJURIES
There are 50,000 WMSDs in Washington every year.
How many of them are due to lifting?
Source: SHARP technical report No. 40-6-2002
17 000 Thats 34%!This means that about 1/3 of WMSDs are attributed to lifting.
That makes it one of the largest single sources
of injury in Washington workplaces.
8/12/2019 backbone safety tips
5/50
LIFTING INJURIES ARENT JUST BACK INJURIES
30% of
Shoulder
WMSDs
22% of
Elbow
WMSDs
13% of
Hand/WristWMSDs
43% of
BackWMSDs
LIFTING RESULTS IN:
Source: SHARP technical report No. 40-6-2002
STATISTICS ON LIFTING INJURIES
8/12/2019 backbone safety tips
6/50
Source: American Society of Safety Engineers (ASSE, 2003)
Lifting Injuries Arent Just Due to AgingOverexertion in lifting a heavy object is the
most frequent single type of injury for those
under 18 resulting in lost work-time.
STATISTICS ON LIFTING INJURIES
8/12/2019 backbone safety tips
7/50
Heavy LiftingPAY SPECIAL ATTENTION TO
FrequentLifting
Awkward Lifting
8/12/2019 backbone safety tips
8/50
HEAVY LIFTING
This worker is adding bags of dry ingredientsto a hopper in a manufacturing plant.
8/12/2019 backbone safety tips
9/50
FREQUENT LIFTING
This worker is palletizing totes of smallparts in a warehouse.
8/12/2019 backbone safety tips
10/50
Above the ShouldersBelow the Knees
At Arms Length
AWKWARD LIFTING
This worker is lifting 50-pound bags of wetfiberglass in a manufacturing plant.
8/12/2019 backbone safety tips
11/50
WISHA Lifting Calculator Other Tools
o ACGIH Lifting TLV
o
NIOSH Lifting Equationo Department of Energys
ErgoEaser
ANALYSIS TOOLS
8/12/2019 backbone safety tips
12/50
PRINCIPLES FOR REDUCING HEAVY LIFTING
Reduce the WeightIncrease the WeightUse Mechanical AssistanceSlide Instead of LiftTeam Lifting
8/12/2019 backbone safety tips
13/50
Reduce the Weight of the LoadREDUCING HEAVY LIFTING
This example shows using lightweight plasticpallets, which weigh from 13 to 30 pounds fora standard 40 x 48.
The traditional wooden 40 x 48 pallet weighs
approximately 60 pounds.
COSTS: About $30 more per unitcompared with wooden pallets
SAVINGS: Reduced shipping costs
(empty pallets are nestable so more can be
shipped back in one trailer)Reduced pallet repair and replacementcosts (plastic is easier to clean when used infood processing)
Fewer splinter/loose nail injuries
8/12/2019 backbone safety tips
14/50
INCREASE theWeight of the Load
Make it so heavy no one
would try to lift it
REDUCING HEAVY LIFTING
2,000
lbs.
8/12/2019 backbone safety tips
15/50
Use Mechanical Assistance
This example shows a mobilepneumatic conveyor that can beused to move powdered andgranular materials from any type
of container (bags, barrels, bins,totes, etc.) to a hopper or otherpart of a mixing system.
The discharge (funnel shapedsilver part at the top) is height
adjustable.
REDUCING HEAVY LIFTING
8/12/2019 backbone safety tips
16/50
Slide Instead of Lifting
This example shows how to move heavy duty batteries from one pallet toanother when picking an order.
Large truck and marine batteries can weigh up to 110 pounds (this oneweighs about 75 pounds). By taking the time to set the order pallet to thesame height as the storage pallet, the battery can be slid rather than lifted.
REDUCING HEAVY LIFTING
8/12/2019 backbone safety tips
17/50
Team
Lifting
Team lifting works better on larger objects, such as the wallboardshown here.
There is a labor cost involved with team lifting, although in some jobsthere is always another person around out of necessity.
REDUCING HEAVY LIFTING
8/12/2019 backbone safety tips
18/50
Use Mechanical Assistance
Avoid Unnecessary Lifting
Use Mobile Storage
REDUCING FREQUENT LIFTING
8/12/2019 backbone safety tips
19/50
Use Mechanical Assistance
The example shown is palletizing using a vacuum lift at apaper mill that produces bundles of grocery bags.
The vacuum lift costs around $10,000, but in this case it
increases productivity by allowing one employee topalletize on more than one line at a time without gettingfatigued.
It also allows rotation of all employees through this job,since physical capacity isnt a limiting factor.
REDUCING FREQUENT LIFTING
8/12/2019 backbone safety tips
20/50
Use Mobile
Storage
The example is a mobile parts rack from a gas and wood stove manufacturer. The
metal parts can be fairly heavy (20 to 52 pounds). They go through several finishingand inspection steps before final assembly.
By placing them on mobile racks, the parts can be moved from process to processwith minimal lifting.
REDUCING FREQUENT LIFTING
8/12/2019 backbone safety tips
21/50
Rotate to Other Jobs
Use MechanicalAssistance
REDUCING DURATION
OF LIFTING
8/12/2019 backbone safety tips
22/50
Rotate to
Non-Lifting
Tasks
REDUCING DURATION
OF LIFTING
8/12/2019 backbone safety tips
23/50
Remove Obstacles
Slide Closer
Reduce Shelf Depth
Reduce Package Size
Use Mechanical Assistance
Team Lifting
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
24/50
Along with object weight, lifting frequencyand duration, the distance between thehands and the low back when lifting is
one of the main factors in determiningwhether a lift is a hazard or not.
The longer the reach required to lift anobject, the more of a load it places on the
low back and the greater the risk ofinjury.
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
25/50
Remove Obstacles
This shows removing the side of atote can reduce can reduce the reachin many cases, although there will still
be some awkward lifting. Its one ofthe cheapest solutions, since itrequires only the time to cut out theside of the tote.
REDUCING AWKWARD
LIFTING/REACHING
Bins with flip-down sides are also available, so that asthey fill up the sides can be flipped-up into place to holdthe boxes in place.
8/12/2019 backbone safety tips
26/50
Slide Objects Closer
This example shows an order picking
using an inexpensive metal hook,made in-house, to pull a box close tothe edge of the shelf before lifting it.This works well for lighter items.
REDUCING AWKWARD
LIFTING/REACHING
Heavier items would need to be stored lower and slidcloser using both hands.
8/12/2019 backbone safety tips
27/50
Reduce Shelf DepthWhile its possible to simply reduce
the depth of shelves, you also give upsome storage space this way, or you
have to buy a lot of narrow shelvingunits.
Gravity flow racks can be a goodsolution, since they allow you to storea lot of boxes on a single deep rack.
They use a variety of types of rollersthat allow boxes to roll forward as thefront box is taken away.
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
28/50
Reduce Shelf DepthThe examples shown are designed to fit intoexisting standard racks, so new gravity flowracks wont need to be purchased and
installed.
REDUCING AWKWARD
LIFTING/REACHING
The costs of these systemsrange from about $60 perlane to a little over $200 perlane depending on depthand width of lanes.
8/12/2019 backbone safety tips
29/50
Reduce Package Size
The drawings show the difference betweenlifting a large box with many items in it versuslifting a smaller box with fewer items in it. Not
only will this reduce the weight, but it will alsoreduce the reach necessary to pick up the box.Costs to implement this idea will vary.
REDUCING AWKWARD
LIFTING/REACHING
If youre the customer, you can request smaller packaging from the
supplier and probably pay a little more per item due to their increasedpackaging costs.
8/12/2019 backbone safety tips
30/50
Use Mechanical
AssistanceThis is an electric hoist on a
trolley attached to a boom. It hasa 250-pound capacity, so theycan actually move two bags at atime, which helps withproductivity.
REDUCING AWKWARD
LIFTING/REACHING
The cost for the light duty hoist, trolley, I-beam and jib mounting isabout $1,000.
8/12/2019 backbone safety tips
31/50
8/12/2019 backbone safety tips
32/50
Use Mechanical
Assistance to Raise the
Load
Add Handles
Arrange Storage
Avoid UnnecessaryLifting
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
33/50
Use Mechanical Assistance to Raise the LoadThis is a relatively common device used inindustrya scissor-lift cart. The height of the cartis adjusted hydraulically, in this case with a footpedal, although powered adjustment mechanisms
are also available. These carts cost about $1,500.
Workers can bring objects up to a better height forlifting, although the best use is to place the cart atthe same height as the shelf or table the object is
being transferred to or from, and then slide it overrather than lifting. Carts with rollers or roller ballsare available to help make the sliding transfereasier.
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
34/50
Add Handles
REDUCING AWKWARD
LIFTING/REACHING
This shows the difference in lifting posture betweenpicking up a box from the bottom, and picking it upusing handles near the top of the box. In this case, thisproduct is shipped in a box with pre-cut handles, so it
doesnt cost anything to use them. Theres still somebending, but the box is now lifted from above theknees, rather than below them.
There are a couple of other good ideas in this photoas well. The box has been stacked on an empty pallet
to raise it up a little (sometimes even raisingsomething just 6 can make a difference in posture).
The bottom pallet has also been designed with sometoe space below the load deck to allow workers to getcloser to the objects theyre lifting.
8/12/2019 backbone safety tips
35/50
Rearrange Storage
The example shown is a from alumberyard, where they took stock ofall heavy items and rearranged their
storage to place those items on shelvesbetween knee and shoulder level.
The higher items can often be sliddown to waist level before lifting them.
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
36/50
Avoid Unnecessary LiftingThis is an example of a commercial productdesigned to allow mechanics to hangwheels off the sides of the lift when working
on brakes, hubs, etc.This places the wheels at a better height forlifting, instead of dropping the wheels to theground. The hanger folds flat against the liftwhen not in use.
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
37/50
REACHING ABOVESHOULDERSArrange Storage
Use Mechanical AssistanceUse a Rolling Stair or Safety
Ladder
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
38/50
Arrange Storage
This shows arranging storage so that
larger, heavier and more frequently usedboxes are between knee and shoulderheight.
In this case, the height of the shelf forheavy boxes is just above the height of the
cart, so they can be slid instead of lifted.
Reaching Above Shoulders
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
39/50
Use Mechanical AssistanceThe device shown is a stacker, which is like ahand truck with a hand-cranked winch tomove the platform up and down so that loadscan be mechanically raised to the height theyare shelved or removed from shelves.
Stackers are available with lift heights up to12 feet. A model with a foot brake to keep itfrom moving when sliding loads is around$780.
Reaching Above Shoulders
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
40/50
This example shows using a cartonclamp on a forklift to split/combine twohalves of a stack of bins, rather thanun-stacking/stacking the top layersover shoulder height.
Use Mechanical Assistance
Reaching Above Shoulders
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
41/50
This is a simple solution, although safety is a
concern when using anything like this. Safetyrules dont allow going up and down ladders
while carrying loads, so a rolling stair orsafety ladder (50 degree slope or less) is
required.
An added advantage is that you can put theload down before going up or down the steps.
Use a Rolling Stair
Reaching Above Shoulders
REDUCING AWKWARD
LIFTING/REACHING
8/12/2019 backbone safety tips
42/50
REDUCING AWKWARD
LIFTING/TWISTING
Use Conveyors
Provide More Space
Arrange Storage
8/12/2019 backbone safety tips
43/50
Use Conveyors
Conveyors such as this one are especiallyuseful when changing directions, to helpavoid twisting. This picture shows a gravityconveyor used to unload trucks in a shipping
department. It allows the receiver to bringthe boxes over to the computer to scan in theinformation and inventory the contents. Theboxes can then be slid directly onto carts tobe put away. Lifting only needs to occurtwice, once to take the box from the truck
and place it on the conveyor, and once to putthe box away. This conveyor set up (gravityrollers) costs about $600.
REDUCING AWKWARD
LIFTING/TWISTING
8/12/2019 backbone safety tips
44/50
This example shows how raising the height of the upper racks can provide moreroom to get at products on the lower racks. This may involve installing additionalracks to make up for the loss in storage space. Otherwise, if the facility can getby with the racks they currently have, then its just labor costs to rearrange the
storage.
Rearrange Storage
REDUCING AWKWARD
LIFTING/TWISTING
8/12/2019 backbone safety tips
45/50
Resources
Your Employees
Your Suppliers
Your Industry Association
Industry-Specific Equipment Catalogs
Product Vendors
Internet Searches
HOW TO FIND IDEAS
8/12/2019 backbone safety tips
46/50
http://www.osha.gov/SLTC/ergonomics/resources.html
ERGONOMICS RESOURCES
8/12/2019 backbone safety tips
47/50
Training all by itself, without making changes to theworkplace, is often noteffective in preventing injuries.
Often employees are taught proper lifting techniques and
then sent out to work under conditions that dont allow them
to use these techniques.
Training is an important part of implementing changes,
though. Showing employees how to use new equipmentand explaining why its important to use it properly in order
to prevent injuries helps to make sure the equipment getsused.
Additional ResourceDaltroy, L.H., et al. (1997). A controlled trial of an educational program to
prevent low back injuries. The New England Journal of Medicine, Vol. 337, No.5, pgs. 322-328.
LIFTING TECHNIQUES TRAINING
8/12/2019 backbone safety tips
48/50
Teaching lifting techniques to
employees
Providing training alone is noteffective
Making changes to jobs andequipment is better
Making changes along withtraining is most effective
LIFTING TECHNIQUES TRAINING
8/12/2019 backbone safety tips
49/50
Being trained where they work, using theobjects they typically lift and the equipmentthey use on the job helps employees to relateto what theyre being taught, rather than
showing them a generic lifting video.
Make sure that employees have learnedwhat youre trying to teach them by havingeach one of them demonstrate the liftingtechniques properly before leaving the class.
Follow-upwith them to make sure they are
able to use the techniques on the job.
LIFTING TECHNIQUES TRAINING
8/12/2019 backbone safety tips
50/50
Job-specific, on-site, hands-ontraining is more effective thanclassroom
Have employees demonstrateproper lifting techniquesbefore graduating
LIFTING TECHNIQUES TRAINING