Post on 04-Apr-2018
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
1/15
Technical DataFuels, Coolants, Lubricants etc.
Consumer Information
I d e n t i f i c a t i o n PlatesTheft PreventionWarranty CoverageTechnical Data
190 E 2.3190 E 2.6
Fuels, Coolants,Lubricants etc.
CapacitiesEngine OilsBrake Fluid
Premium Unleaded GasolineFuel RequirementsGasoline AdditivesCoolantsConsumer InformationProblems with your VehicleReporting Safety Defects
1061 0 7
1 0 8
1091 1 0
1 1 2
1 1 2
1 1 4
1 1 4
1 1 41 1 5
115116117118119
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
2/15
Identification Plates
When ordering spare parts, pleasespecify vehicle identification andengine numbers.
1 Certification Tag(left door pillar)
identification Tag2
34
Vehicle Identification No.Engine No.(190 E 2.3: front left)
Body No. and Paintwork No.5
6 Information TagCalifornia versionVacuum line routing foremission control system
Emission Control Tag
106
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
3/15
Theft Prevention Spare parts are similarly labeled
This vehicle complies with the at the factory in a different
U.S. Federal Motor Vehicle Theft tion. The labels show the letter
Prevention Standard (49 CFR Part (for replacement) instead of the
5411. Enaine. transmission and
parts (see illustration)are labeled at the factory, thelabels show the ofthis vehicle.
Location of labels
1 Bumper front/rear
2 Engine hood
3 Trunk lid
4 All fendersAll doors
Engine*: on engine block, rear
Transmission*: on transmission,left front
not shown in illustration
Note:
Do not remove these labels. Theselabels are intended for partstification in case of theft. Whenplacing parts subject to labeling,please make sure that the partsyou receive are labeled properly.This is especially important whenwork is performed outside of theUnited States.
107
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
4/15
Warranty Coverage
Your car is covered under theterms of the warranties printedin the Owners Service andWarranty Policy Booklet, and yourauthorized Mercedes-Benz dealer
will exchange or repair anydefective parts in accordance withthe terms of the followingwarranties:
1. New vehicle limited warranty
2. Emission system warranty
3. Emission performance warranty
4. California emission controlsystems warranty.
Loss of Owners Service andWarranty Policy
Should you lose your OwnersService and Warranty PolicyBooklet, have your authorizedMercedes-Benz dealer arrange for
a replacement. It will be mailed toyou.
108
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
5/15
Technical Data 190 E 2.3
Model 190 E 2.3 (201 028)
Enaine 102
Mode of operation 4-stroke engine,injection
No. of cylinders 4
Bore 3.76 in (95.50 mm)
Stroke 3.16 in (80.20 mm)
Total piston displacement 140.2 (2298Compression ratio 9.0
Output to SAE J 1349 130 rpm(97
Maximum torque toSAE J 1349 146 ft-lb/3500 rpm(198
Maximum speed 6000
order l - 3 - 4 - 2
Polv-V-belt 1980 mm
Rims Tires
Rims (light alloy rims)Wheel offset 1.9 in (49 mm)
Summer tires:Radial-ply tires 15 87 H
Winter tires:Radial-ply tires
Electrical System
Alternator
Starter motor
BatterySpark plugs
Electrode
12 V/1.4
12 V/62 AhBosch H 8Beru 14 K-8 DUOChampion S 10 YCC0.032 in (0.8 mm)
Weights
Roof load max.
Trunk load max.
See certification
220 lb (100
220 lb (100
Main Dimensions
Overall vehicle width
Overall height
Wheel base
Track, front
Track, rear
66.5 in (1690 mm)
54.1 in (1375 mm)
104.9 in (2665 mm)
56.7 in (1441 mm)
55.9 in (1421 mm)
The quoted data apply only to the standard vehicle. See anMercedes-Benz dealer for the data of all and equipment.
109
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
6/15
Technical Data 190 2.6
Model 190 E 2.6 (201 029) Rims Tires
Standard model (without Sportline option):
Rims (light alloy rims)Wheel offset 1.9 in (49 mm)
Engine 103
Mode of operation 4-stroke engine,qasoline injection
No. of cylinders 6
Bore 3.26 in (82.90 mm)
Stroke 3.16 in (80.20 mm)
Total piston displacement 158.5 (2597
Compression ratio 9.2
Output to SAE J 1349 158 rpm(118 rpm)
Maximum torque toSAE J 1349 162 ft-lb/4600 rpm(220
Maximum speed 6450 rpm
Firing order l - 5 - 3 - 6 - 2 - 4
Polv-V-belt 2415 mm
The quoted data apply only to the standard vehicle. See anMercedes-Benz dealer for the data of all
and special equipment.
Summer tires:Radial-ply tires 15 87 V
Winter tires:Radial-ply tires
Sportline model:
Rims (light alloy rims)Wheel offset 1.7 in (44 mm)
Summer tires:
Radial-ply tires ZR 15Winter tires:Radial-ply tires
or:
Rims (light alloy rims)Wheel offset 1.9 in (49 mm)
Winter tires:Radial-ply tires
110
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
7/15
Technical Data 190 E 2.6
Electrical System
Alternator
Starter motor
BattervSpark plugs
Electrode
12 V/1.7
12 V/62 AhBosch 9Beru 14 K-9 DUOChampion S 12 YCC0.032 in (0.8 mm)
Weights
Trunk load max.
See certification
220 lb
Main Dimensions
Wheel base 104.9 in (2665
Track, front 56.7 in mm )
Track, rear 55.9 in (1421
111
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
8/15
Fuels, Coolants, Lubricants etc. Capacities
Vehicle components and their respective lubricantsmust match. Therefore use only brands testedand recommended by us. Inquire at yourauthorized Mercedes-Benz dealer.
Capacity Fuels, coolants, lubricants etc.
Engi
190
ne with oil filter Recommended engine oils
E 2.3 5.3 us qt (5.0 I)temp SAE grades
190 E 2.6 6.3 US qt (6.0 I)
- 1 0
- 1 5
20
Manual transmission 1.6 US qt (1.5 I) MB Manual transmission fluid
Initial fill:Automatic transmission 7.5 us qt (7.1 I)Fluid change:6.3 US qt (6.0 I)
Automatic transmission f luid
112
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
9/15
Capacity Fuels, coolants, lubricants etc.
Rear axle 1.2 us qt (1.1 I) Hypoid gear oil SAE 90, 85 W 90
Rear axle with automaticlocking differential (ASD)
1.2 us qt (1.1 I) Hypoid gear oil SAE 90 for limitedslip differential
Hydraulic system for automaticlocking differential (ASD)
approx. 2.1 US qt (2.0 I) MB Hydraulic fluid
Power steering 1 us qt (1 .o I) MB Power steering fluid
Accelerator control linkage Hydraulic fluid
Front wheel hubs 2.1 oz (60 g) High temperature rollerbearing grease 3
Brake and (with manual approx. 0.5 US qt (0.5 I) MB Brake fluid (DOT 4)transmission) clutch reservoir8
Windshield washer system approx. 3.2 US qt (3.0 I)MB Windshield washer concentrate
Windshield washer system and approx. 5.3 US qt (5.0 I)headlamp cleaning system
Fuel tankincluding a reserve of
Cooling system
approx. 14.5 US gal (55 I) Premium unleaded gasoline: Postedapprox. 1.6 US gal (6.0 I) Octane 91 (Average of 96 RON/86 MON)
approx. 10.0 US qt (9.5 I) MB Anticorrosion/antifreeze
Use MB Washer Concentrate and water for temperatures above freezing orMB Washer Concentrate and commercially available premixed washer
for temperatures below Follow suggested ratios, see Index
113
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
10/15
Engine Oils
Engine oils are specifically testedfor their suitability in our engines.Therefore, use only engine oilsrecommended by Mercedes-Benz.Information on recommended
brands is available at yourauthorized Mercedes-Benz dealer.
Brake
During vehicle operation, theboiling point of the brake fluid iscontinuously reduced through theabsorption of moisture from theatmosphere. Under extremely hard
operating conditions, this moisturecontent can lead to the formationof bubbles in the system thusreducing the systems efficiency.
The brake fluid must therefore bereplaced every two years, prefer-ably in the spring.
It is recommended to use onlybrake fluid approved by Mercedes-Benz. Your authorized Mercedes-
Benz dealer will provide you withadditional information.
Premium Unleaded Gasoline
Caution!
To maintain the engines durabilityand performance, premium un-leaded gasoline must be used. If
premium unleaded is not availableand low octane fuel is used, followthese precautions:
l have the fuel tank filled onlypartially with unleaded regularand fill up with premium un-leaded as soon as possible,
l avoid full throttle drivingabrupt acceleration,
and
l do not exceed an engine speed
of 3000 rpm, if the vehicle isloaded with a light load such astwo persons and no luggage,
l do not exceed of maximumaccelerator pedal position, if thevehicle is fully loaded or operat-ing in mountainous terrain.
114
EXIT
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
11/15
Fuel Reauirements The ratio of Methanol to gasoline
Use only Premium unleadedmeetina ASTM standard D 439:
must not exceed 3% plusadditional cosolvents.
The number (posted at the Using mixtures of Ethanol and
pump) must be 91 min. It is an Methanol is not allowed. Gasohol,
average of both, the Research (R)
which contains 10% Ethanol and
octane number and the Motor (M) 90% unleaded gasoline, can beoctane number: + This used.
is also known as ANTI-KNOCK These blends must also meet allINDEX. other fuel requirements such as
Unleaded gasoline containing resistance knock, boiling
oxvaenates such as Ethanol, range, vapor pressure etc..
TBA can be useded the ratio of any one of theseoxygenates to gasoline does notexceed 1 MTBE not to exceed
15%.
Gasoline Additives
A major concern among enginemanufacturers is carbon build upcaused by gasoline. Mercedes-Benz recommends to use onlyquality gasoline containing
additives that prevent the build upof carbon deposits.
After an extended period of usingfuels without such additives,carbon deposits can build upespecially on the intake valvesand in the combustion area,leading to engine performanceproblems such as:
l warm-up hesitation,
l unstable idle,l knocking/pinging,
misfire,power loss.
Do not blend other specific fueladditives with fuel. They onlyresult in unnecessary cost, andmay be harmful to the engineoperation.
115
Damage or malfunctions resultingfrom poor fuel quality or fromblending specific fuel additives arenot covered by the Mercedes-Benz Limited Warranty.
EXIT
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
12/15
Coolants
The engine coolant is a mixture ofwater andfreeze, which provides:
corrosion protection
freeze protectionl boiling protection (by increasingthe boiling point).
The cooling system was filled atthe factory with a coolant provid-ing freeze protection to approx.
F (-30 C) and corrosionprotection.
The coolant solution must be usedyear round to provide the neces-sary corrosion protection and in-crease in the boil-over protection.You should have it replaced every3 years.
To provide the important corrosionprotection, the solution must beat least 45%freeze (equals a freezeto approx. F If youuse a solution that is more than55% anticorrosion/antifreeze
(freeze protection to approx.-49F the engine tem-perature will increase due to the
lower heat transfer capability ofthe solution. Therefore, do not usemore than this amount ofanticorrosion/antifreeze.
If the coolant level is low, waterand MB anticorrosion/antifreeze
should be used to bring it up tothe proper level (have coolingsystem checked for signs ofleakage).
The water in the cooling systemmust meet minimum requirements,which are usually satisfied bynormal drinking water. If you arenot sure about the water quality,consult your authorizedMercedes-Benz dealer.
Anticorrosion/antifreeze
Your vehicle contains a number ofaluminum parts. The use ofaluminum components in motorvehicle engines necessitates thatanticorrosion/antifreeze coolantused in such engines be specifi-cally formulated to protect thealuminum parts. (Failure to use
such anticorrosion/antifreezecoolant will result in a significantlyshortened service life.)
Therefore the following product isstrongly recommended for use inyour car: Mercedes-Benz
Anticorrosion/Antifreeze Agent.
Before the start of the winterseason (or once a year in the hot
southern regions), you shouldhave the anticorrosion/antifreezeconcentration checked. Thecoolant is also regularly checkedeach time you bring your vehicleto your authorized Mercedes-Benzdealer for maintenance service.
Approx. freeze Anticorrosion/protection antifreeze
-35F(-37C) 4.8 US qt (4.50 I)
-49F(-45C)
5.5 US qt (5.25 I)
116
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
13/15
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
14/15
Problems with Vehicle
If you should experience a problem with your vehicle, particularlyone that you believe may affect its safe operation, we urge youto immediately contact your authorized Mercedes-Benz dealerto have the problem diagnosed and corrected if required.If the matter is not handled to your satisfaction, please discussthe problem with the dealership management, or if necessarycontact the Owner Service Manager at the Mercedes-BenzRegional Office nearest you (see Owners Service and WarrantyInformation booklet for addresses). You may also write directlyto us at the following addresses:
In the U.S.A.: Owner Service DepartmentMercedes-Benz of North America Inc.
One Mercedes DriveMontvale, NJ 076450350
In Canada: Owner Service DepartmentMercedes-Benz Canada Inc.849 Eglinton Avenue EastToronto, Ontario,
118
EXIT
EXIT
7/29/2019 90006 Technical Data Fuels Coolants Lubricants
15/15
For the U.S.A. onl y .
The following text is published as required of manufacturers underTitle 49, Code of U.S. Federal Regulations, Part 575 pursuant to theNational Traffic and Motor Vehicle Safety Act of 1966.
Reporting Safety Defects
If you believe that your vehicle has a defect which couldcause a crash or could cause injury or death, you shouldimmediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifyingMercedes-Benz of North America Inc..
If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect existsin a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved inindividual problems between you, your dealer, orMercedes-Benz of North America Inc..
To contact NHTSA, you may either call the Auto Safety Hotlinetoll-free at l-800-424-9393 (or 366-0123 in Washington, D.C. area)or write to: NHTSA, U.S. Department of Transportation,Washington, D.C. 20590. You can also obtain other informationabout motor vehicle safety from the Hotline.
119
EXIT