Post on 04-Apr-2018
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
1/24
828A Heavy duty length cutting machine
for lifting and tie-down belts (hot)
828B Heavy duty industrial cutting machine
for Synthetic Fiber Rope (heat cutter)
Instructions Manual &
Illustrated Parts Catalogue
This catalog has been prepared to guide you while operating 828 class hot cutting machine and arranged to simplify
ordering spare parts.
Before putting the machines described in this manual into service, carefully read the instructions. The starting of each
machine is only permitted after taking notice of the instructions and by qualified operators.
Edition No.: English 2.0
Rights Reserved In All Countries
Printed in China
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
2/24
HIGHTEX
- 1 -
Company Introduction
HIGHTEX Company is a specialist machine maker, specializing in
electronic cutting machines. Micro computer belt cutting machines,
Might Adhesivegluing machines,Milky-white gluegluing machines,
And other leather bags mechanical design and manufacturing.
Out machines are widely used for making handbags, suitcases, leather
articles, insulating wares, HIGHTEX has a strong research and
development ability. It has a complete quality management system andgood services for per-sale and after-sale, it can provide customers with
best services.
HIGHTEX Company persists in a notion ofman is fumdamental and
Customer is first, it regards honesty, technology, progress and
responsibility as enterprise spirit, it provides customers with stable
characters, good quality, humanized operation, bigh efficiency and
speed professional output, these machine are the products which can
create high profit.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
3/24
HIGHTEX
- 2 -
CATALOGUE
Preface 3
Chapter 1 Machine Structure 4
1 .Install the material loader 4
2. Control Panel 4-10
3. Install and adjust the cold knives 10-11
4. Install and adjust the hot knives 12
5. Install the tension gear 12
Chapter Maintain the Machine and its hints 13
Chapter3SimpleTroubleshooting 13-14
Chapter 4 After Sale Service 14
Chapter 5 Wire Diagrams 15Chapter6Explosive Drawing of the parts 16
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
4/24
HIGHTEX
- 3 -
PREFACE
Thank you for your wise selection to buy our products. We provide you
not only quality machine, but also a reliable after-sale service.
For operators body safety, and for protecting the machine, it is
absolutely necessary to read this operational manual very carefully
before you operate this machine. Please pay attention to the usage hints.
This manual introduces in detail the machine structure, operational
regulations, maintenance, the troubleshooting for the possible troubles
and the wire diagrams. If you still have any questions, please do not
hesitate to contact our sales representatives who will be glad to serve
you.
SPECIAL DECLARATION
*Any claims cannot be lodged based on the contents of this
operational manual.
*Our company has the absolute right to explain the meaning of
this operational manual. All the explanation on this operational
manual must be subject to our explanation.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
5/24
HIGHTEX
- 4 -
CHAPTER 1 MACHINE STRUCTURE
1. Install the material loader (FIG. A)
(1) After you tighten the screw (5), the material weight will beincreased.
(2)Do not allow the movable metal discs (6) to clamp the materialstoo tight. Leave a gap.
12
3
45
67
material
material
FIG. A
2.OPERATIONAL PANEL (FLG.B)
FIG. B
* HIGHTEX Auto Strip Cutting Machine *
Knife A = 0 Mode = normal
Length A = 0000.0 Speed = 00
Total: 00000 Finish= 000:00000
HIGHTEX
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
6/24
HIGHTEX
- 5 -
(1) FUNCTIONS
FWD+: Press this button, and the roller clockwise turns. For
setting length, this button can be used for setting the
figures after the decimal.
REVERSE-: Press this button, and the roller will
counterclockwise turns. For setting length, this
button can be used for setting the figures after the
decimal.
/
CLR/CUT: Press this button, and the knife will cut once. Itcan be used to clear the error values on the setting
footage.
A
LENGTH A: Press this button, then press figure buttons to
set the LEN length A.
SPD: Press this button, then press figure buttons to setspeed within a range from 00 to 99.the bigger the figure
is, the fast the speed is.
UNIT: Press this button, then press figure buttons to set the
number of the cutting lots. If the setting is 0,the knife
wont cut.
TOL: Press this button, then press figure buttons to set totalcutting quantity.
A
CUT A Press this button, then press figure buttons to set
the number of cutting times for knife A.
After you finish each of the above setting, you must press SET
button once so as to save the setting value. If you finish the
setting, and want to return to the main menu, just press STOP
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
7/24
HIGHTEX
- 6 -
button.
CMP: Press this button to clear the number of the finished
cutting times.
RUN: Press this button to start the machine.
FUN: Before you selectFeeding mode, following setting is
invald.
F00Time delay for cutting
F01Cutting interval
F02Hold cutting for each lot: If the setting is 0, the knife will keep on
cutting till the total cutting quantity is completed. You must
press CMP button again, then press RUN button so as to
restart.
F03Point search speed: 1~5x100 HzF04Point length searching: the range of the point search length is
from 0 to 255mm. If the setting is 0, the sensor cannot the point.
The length B, the Knife B, the length C and the knife C will
immediately carry out the cutting action.
F05Knife B: Press this button to set the number of knife B cutting
times. If the setting is 0, the knife has no action.
F06Length B: Press this button to set the size of Length B. if the
setting is 0, there will be no action.
F07Knife C: Press this button to set the number of knife C cutting
times. If the setting is 0, the knife has no action.
F08Length C: Press this button to set the size of Length C. If the
setting is 0, there will be no action.
After you finish each of the above setting, you must press SET
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
8/24
HIGHTEX
- 7 -
button once to save the parameter. Then, press SET button
again so as to shift to next function setting. After all the settings
are completed, press STOP button to return the main menu.
0. Pulse 0=1P, 1=2P Setting 1
1. Feeding Mode 0=CW, 1=CCW Setting 1
2. Jog speed 099 Setting2 4
3. Top limit of speed 99=9.9khz Setting99
4. Bottom limit of speed 10=1.0khz Setting00
5. Cutting mode 0 Knife of motor
1 Knife A of cylinder2 Knife B of cylinder3 Knife of flywheel
6. Feeding mode 0=normal
1=searching the point
7. Acceleration 04 Setting 4
8. Multiplied by length 1~99 Setting 1
9. Divided by length 1~99 Setting 1
(2) Setting a certain cutting length
ExampleThe cutting length desired is 150.4mm. The total cutting
quantity are 1200 strips. 12 strips are packed in one box. Turn on the power switch to enter the operational footage. Set the cutting length 150.4.
A 1 5 0
A 1
1 2 0 0
LEN 1 SET5 0 +
TOL 1 2 0 0 SET
CUT 1 SET
If the pressed figure is bigger than4, you
may press CCW button [-] to return to 4.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
9/24
HIGHTEX
- 8 -
1 2
After you complete above settings, please press STOP button toexit. Then, the footage will display each of you set parameters.
If an error setting is found for example, the length setting becomes
250.6mm, the other settings are correct, then you may repeat the
step 1 for correction.
Place the material: Adjust the material spacers. Fix the material by
the spacers so that the material wont slant, but do not clamp the
material, or the cutting length wont be accurate.
Feed the material between the upper roller and the lower roller.
Press CW [+] button till the front end of the strip over the knife
position. Press START button [RUN]. Then, you have completed
auto cutting.
(3) SET 2 OR 3 KINDS OF LENGTH CUTTING
SPD
Select your desire speed. The speed from slow [00] to fast[99], total 100 speeds. If the material is flexible, or the
material wed is heavier without the support of the feeding
SET
UNIT 1 2 SET
SETFUNSet the hold time for each lot depending on the actualneed, but the holding time cannot be 0.
**HIGHTEX Auto Strip Cutting Machine**
F02 SETTINGKnife A=0 Mode=cut
Length A=0150.4 Speed=10
Hold time of lot=0 19
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
10/24
HIGHTEX
- 9 -
This machine can cut 3 different lengths in one cycle. This function
is often used in electronic industry to cut conduction or insulation
material. The Cutting process is shown below:
Turn on the power switch. When the footage a appears, press
FUN button to enter the setting mode.
After above step is completed, you can enter footage b. Pleaseenter parameter code ****. Then, press SET button.
After above step is completed, you can enter footage c. Press FUN
button, and the cursor will jump to the position of the parameter
number. Then, press 8 to enter the feeding mode.
After entering the feeding mode, there are 2 selections 0 and 1. 0 is
LEN B LEN CKnife Knife Knife
LEN A
HIGHTEX HIGHTEX
HIGHTEX HIGHTEX
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
11/24
HIGHTEX
- 10 -
normal mode. 1 is point search mode. Now you select 1 to enter
point search mode. Then, press SET button. Press STOP button to
exit the set mode.
After above setting iscompleted, you can
enter footage e, and
find Mode = point
search. Thus, the
point search function
is stated.
Operate the procedure from step 1 to step 4 of
the point-search function. Select 0 for the
feeding mode. Then, follow the following step
to return the normal mode. After that, the
footage f appears Mode =normal. It means that
the point-search
function is cancelled.
After point-search function is started, the machine can cut 3 different
lengths, such as 126.1mm, 448.0mm and 168.8mm.
HIGHTEX
HIGHTEX
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
12/24
HIGHTEX
- 11 -
0
FIG. C
0
1
4 4 8
1
1 6 8
After above setting is completed, press STOP button to exit thesetting mode.
FUN 0 SETSET
0 SETSET
1 SETSET
4SET 4 8 SET
1 SETSET
Enter F7. Set 1 for
1SET SET6 8 +
Enter F8. Set 168.8 for
Enter F5 to set 1 for
Enter F4 to set 0 for
If you press the one more button, and get abigger figure than you want, you may pressCCW [-] button to return to the figure whichyou want.
Please press SET button two
times more. Enter F3 footage,
and set the point search speed
Enter F6. Set 448 for length
HIGHTEX
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
13/24
HIGHTEX
- 12 -
M6*15
M6*12
If you just need to cut two different lengths, please set 0 for both
length C and knife C. thats all.
After exiting the setting mode, set 126.1 for length A according to the
procedure mentioned in above [2. Setting a certain cutting length].
3. Install and Adjust the Cold Knives (Fig. D)
Be very careful when you replace
the knives so as not to damagethe knife edge!
(1). Use one 5mm hex wrench to remove
the 3 set screws of the upper cold knife.
Then, remove the upper cold knife.
(2). Use a Philips screwdriver to remove 3 set screws of the lower cold
knife. Then,
remove the lower cold knife.
(1). Use one piece of clean cotton cloth or gauze
to clean the knives and the knife contact areas
of the machine.
(2). Install the lower cold knife to the machine. Verify
that the upper cold knife and the lower cold knife
perfect contact the connecting plate. Then, tighten
the 3 set screws to the lower cold knife. Fig. E
(3). For the convenience of installing the upper cold knife, please make
knife adjustment manually. Adjust the slide to the highest position.
Then, install the upper cold knife. At this time, do not tightened theset screws of the upper cold knife. See Fig. E.
M6*15
M6*12
Lower cold knife
Upper cold knife
Round cross-head screw M6x12
Connecting plate
Slide plate
Fig. D
Knife manualadjustment
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
14/24
HIGHTEX
- 13 -
L8
(4). Manually adjust the slide to the lowest position. Then, tighten the set
screws of the upper cold knife. Please tighten the set screw at the
central posit first. Then, tighten the rest 2 set screws on both sides.
(5). Make a manual adjustment so that the edge of the upper cold knifemoves slowly off the edge of the lower cold knife, but do not let the
edges completely off. Repeat this action several times to remove the
burrs adhered to the edges of the knives. Then, adjust the slide to the
highest position.
(1). Before adjust the machine, please turn off the power switch for
safety purpose.(2). After installing the knives, tighten the nuts (N). Firmly touch the
screw (P) by a philips screwdriver so that the screw wont follow the
nut to turn, but do not tighten the screw (P) too deep (too tight), or the
screw will touch the slide (M), and jam the slide.
(3). Use one L8 wrench to move the slide so that
the slide can slowly grind the upper and lower
cold knives. This action helps the contact of
the knives. When the slide is moved to the
highest position, use the knife manual
adjustment to test cutting. Fig. F
(4). After cutting test, if the left-hand side material cannot be completely
cut off, or
has cutting burrs, please tighten a little the left-hand side nut, and
loosen a little
the right-hand side nut (N). Then, test the cutting again. If the material
is still cannot be perfectly cut off, repeat the above action till the
cutting result is perfect. If you still cannot completely cut off the
material, please add one piece of paper to the back of the knife blade
at the place where the material cannot be cut off. This paper canincrease the contact area between the upper and lower knives at the
L8 wrench
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
15/24
HIGHTEX
- 14 -
material-not-off place. If the right-hand side material cannot be
completely cut off, please tighten a little the right-hand side nut and
loosened a little the left-hand side nut, and make the same manual
adjustments as above.
For tighten the hot knives, please tighten the lower knife seat (88) first.
Then, tighten the heat insulation plate (91), hot knives (92) and the
copper heating elements (93) accordingly. Note! The lower knife pad
(85) is not allowed to be higher than the upper plane of the lower knife
seat (88), or the material feeding wont be smooth. Remove or replacethe knives in the reverse order. Please use manual mode to cut once.
If the operation is normal, then you can start cutting. See Fig. G.
It is necessary to install a tension gear (11) when the material wed is
heavier so as to reduce the loading of the feeding motor, and keep thecutting precision.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
16/24
HIGHTEX
- 15 -
CHAPTER2 MAINTAIN THE MACHINE AND ITS HINTS
1.Please input correct correct voltage with a tolerance of 10V.Practically ground the machine to avoid the damage caused by
electricity leakage.
2.Be sure to switch off the power, and pull out the plug before you makeany adjustment with the machine. It is for your body safety. Do not
allow children or non-authorized operators to be close to the machine
so as to avoid danger.
3.When you blow off the dust from the computer box by air gun, the airmust not contain moisture. If there is moisture, please drain the water
in the air compressor.
4.Please use lubricant #40 for the machine. The lubricating positionsare marked on the lateral covers of the machine.
5.In cold place the grease inside the machine might be frozen. Pleaseinsert one L8 wrench into the knife manual adjustment hole. Turn the
wrench according to the turning direction shown on the cover, and
also feed the normal-temperatured lubricant into the lubricatingpositions. Turn the wrench slowly till the knife blades are not jammed.
Then, you can start the machine.
6.The back of the machine must be 40mm off the wall. Reserve repairspace on both sides of the machine.
7.Be very carefully when you replace the knives so as to avoidfinger/boby injure canused by the knives. Besides, be sure to pull out
the plug.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
17/24
HIGHTEX
- 16 -
CHAPTER3 SIMPLE
TROUBLESHOOTING
1. Turn on the power switch. If the control panel displays nothing, and nolamp lights, the fuse might blow. Please replace it with a correct fuse.
2.The knife keeps on cutting when there is no material: Please adjustthe position of the proximity switch to a proper place where it can
properly detect the induction screw, but it cannot touch the induction
screw. If the problem still exists, the proximity switch or the computer
box might be down.
3. The cutting length is incorrect:
(1). The upper roller doesnt have
enough 111 pressure. Adjust the
pressure nut to 11 1 increase the
pressure. See Fig. I.
(2). The set screws of the feeding motor
are
loose. Tighten the screws.
(3). The screws of the belt wheel of the lower
roller are loose, or the screws of the belt
wheel of the feeding motor are loose.
Tighten all of these screws.(4). The machine cuts two strips at the same time, and the two cut
pieces have different lengths: Adjust the pressures on both sides of
the upper roller till the two cut pieces have the same length.
(5). The feeding motors shakes while feeding, and cannot operate
smoothly: The driving box is down. Please replace it with a new
one.
4. Press START BUTTON, but the machine has no action:(1). The preset cutting length or the preset cutting quantity is zero,
Fig. I
Pressure nut ofUpper roller
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
18/24
HIGHTEX
- 17 -
therefore the machine wont work. Please enter a correct setting
figure.
(2). The preset cutting quantity is equal to the quantity which has been
cut already. Please press RESET BUTTON.(3). If all above measures are invalid, the computer box is down.
5.The hot cutting cannot cut off the belt:(1). The knife edge is indented or dull. Please regrind or sharpen it.
(2). The lower knife pad has deep cuts. Replace the pad.
(3). The copper heating elements are aged. Whose power shown in
the meter is low. Replace the copper heating elements.
(4). The setting temperature is too low. Please raise the settingtemperature.
(5). The material is too thick. Please make a new setting, and increase
the number of cutting.
6. The cold cutting cannot cut off the material:
(1). The knife edge is indented or dull. Regrind or replace it.
(2). The material is partially cut off: please add one pieced of paper on
the back of the lower knife.
(3). Adjust the gap screw of the knife. Loosen the nuts. Then, tighten
the screws. After that, tighten the nuts.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
19/24
HIGHTEX
- 18 -
CHAPTER 4 AFTER-SALE SERVICEWe offer one (1) year guarantee for free maintenance and repair of
the machine from the delivery date, but we are not responsible for
following events:
a. The machine is damaged during the transportion arranged by
yourselves.
b. Do not install a voltage stabilizer when you install the machine at
an unstable voltage place, thus the machine is damaged.
c. Use incorrect voltage which results in machine damage.
d. Modify the machine without our prior written permission, and
damage the machine.
e. The machine is not sold directly from us to you, but through a
middle man or other seller.
f. The machine is not repaired or disassembled by our authorized
persons (or technicians), thus the machine is damaged.
g. Natural disasters or under force majeure.
h. The consuming parts, such as cold knife, copper heating elements,knife pad, rubber roller, proximity switch, button switch, hot knife
and heat insulation board.
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
20/24
HIGHTEX
- 19 -
CHAPTER 5 WIRE DIAGRAM
Step motorDX-B23HB
A C110V
Flat cableFor buttons LCD shadeLCD contrast
LC DFlat cable
Step pulse signalKnife ofcylinder
1Air blow valve(cutting interval)
Output voltageAC 220V
A C220V
M ode of cylinder knife B
Safetyvalve
Sensor B Point searchsensor
Sensor A
Mode ofCylinder Knife A
Sensor A oftop start point
of cylinderknife
Sensor A ofCylinder knife
Sensor A
LCD flat cableLCD shade
Sensor B ofcylinder knife
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
21/24
HIGHTEX
- 20 -
CHAPTER 6 EXPLOSION DRAWING OF
PARTS
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
22/24
HIGHTEX
- 21 -
#828 PART LIST NO.1
N0. NAMES OF PARTS NO. NAMES OF PARTS
1 Machine main frame 23 Belt wheel of cam shaft
2 Slide seat 24 Top screw M6x10
3 Lower cold knife 25 Inducing ring
4 Socket head hex screw M6x12 26 Socket head hex screw M10x20
5 Pad of lower knife 27 Hex head screw M6x25
6 Flat head Philips screw M5x12 28 Copper lever
7 Slide rule 29 Cam
8 Pillar of slide rule 30 Gasket of cam
9 Fixed seat for knife adjustment 31 Flat head Philips screw M6x8
10 Socket head hex screw M6x45 32 Socket head hex screw M6x12
11Spring: wire dia.10, inner
dia.4.0 and length 2233 Bolt for copper lever
12Spring: wire dia.10, inner
dia.4.0 and length 2734 M6 washer
13Spring: wire dia.10, inner
dia.4.0 and length 3435 Fixed board of proximity switch
14 Fixed plate for knife adjustment 36 Big flat head Philips screw M4x6
15 M6 nut 37 Philips screw M3x20
16 Round head Philips M6x30 38 Proximity switch17 Unloading board for cold cut 39 M3 nut
18 Socket head hex screw M6x10 40 Lower roller
19 Bearing 6004 41 Key 6x15
20 Shaft of cam 42 Fixed sleeve of lower roller
21 Key 6x30 43 Bearing 6202
22 Key 6x30 44 Bearing seat
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
23/24
HIGHTEX
- 22 -
45 Left/right arm of upper roller 69 Socked head hex screw M6x100
46 Set screw for left/right arm of upper roller 70 Fan front cover
47 Big flat head Philips M4x8 71 Fan front cover
48 Lever of upper roller 72 Big flat head philips screw M5x6
49 Upper roller 73 Transmitting gear of upper roller
50 Pressure bolt for upper roller 74 Belt wheel of upper roller
51Pressure spring of upper roller, wire
dia.1.4, inner dia.6.5 and length 4575 Motor for knife
52 Pressure nut of upper roller 76 Fixed board of knife motor
53 Fix block for feeding 77 Hex head screw M6x20
54 Socket head hex screw M6x25 78 Belt wheel of knife motor
55 Fixed bar for feeding 79 Belt wheel of knife motor
56 Material separating board 80 Step motor
57 Top screw M4x10 81 Fixed board of step motor
58 Set screw of material separating board 82 Belt wheel of step motor
59 Set nut of material separating board 83 Belt wheel of step motor
60 Connecting plate 84 Control box
61 Flat head Philips screw M4x8 85 Lower knife pad
62 Material pressing board 86 Pillar of lower knife pad
63
Spring wire of material pressing
board: wire dia. 0.6, inner dia.6.0
and length 34
87 Spring f lower knife pad: wire dia.1.6, inner dia. 8.5 and length 32
64 Slide 88 Pad seat of lower knife
65 Fixed sleeve of material pressing board 89 Pillar fixed sleeve for lower knife pad
66 Round head philips M4x8 90 Socket head hex screw M6x35
67 Socket head hex screw M6x100 91 Heat insulation board
68 Upper cold knife 92 Hot knife
7/31/2019 828 Length (Hot) Cutting Machine for Polyester Lifting Slings and Cargo Lashing Strap
24/24
HIGHTEX
93 Copper heating block 97 Rear baffle
94 PW 6.5x19x2 98 Left cover
95 Socket head hex screw M6x50 99 Safety cover
96 Unloading board for hot cut
TOOL LIST
No. NAMES No. NAMES
1 Hex head wrench L3 5 Open end wrench 10-12
2 Hex head wrench L8 6 Long, Philips screw knife
3 Hex head wrench T4 7 Oil pot
4 Hex head wrench T5
(for hot cut)8 Short, Philips screw knife
(for hot cut)