Post on 19-May-2020
• Strength of terminals : pull-out force 10 N max.• Torque : 1 Nm max. applied between the 2 nuts• Max. panel thickness : 1.5 mm (.059) with 2 nuts
GENERAL SPECIFICATIONS
• Max. current/voltage rating with resistive load : - gold plated contacts : 0.4 VA 20 V max. AC or DC - silver plated contacts : 0.5 A 48 V max. AC or DC
• Minimum load : 10 mA 50 mV - 10 µA 5 VDC• Contact resistance : 20 mΩ max.• Insulation resistance : 1,000 MΩ min. at 500 VDC• Dielectric strength: 1,000 Vrms 50 Hz min. between terminals and
frame, 500 Vrms 50 Hz min. between terminals• Electrical life at full load :
ELECTRICAL SPECIFICATIONS
Contacts Number of cycles
2 positions 3 positions
Gold plated 60,000 30,000
Silver plated 20,000 10,000
• Operating temperature : -30 °C to +85 °C (-22 °F to +185 °F)• Moisture : 21 days 95 % (NFC 20-603 - IEC 8-2-3)
ENVIRONMENTAL SPECIFICATIONS
Ø 4.83 mm threaded bushingSolder lug and straight PC terminals
DISTINCTIVE FEATURES
ZL seriesSubminiature toggle switches • metal bushing
The company reserves the right to change specifications without notice.
PAN
EL S
WIT
CH
ES
1
SW-ZL-171
1
Subminiature toggle switches • metal bushing
ZL series
• Hand soldering : 280 °C (536 °F) max. for 5 seconds max.• Wave soldering : 260 °C (500 °F) max. for 5 seconds max.
SOLDERING
• Case : thermoplastic UL94-V0• Actuator : brass, nickel plated• Bushing : zamac, tin plated• Contacts and terminals :
0 : brass, gold plated (standard) 1 : brass, silver plated 3 : brass, gold plated (1.27 micron gold)
• Terminal seal : epoxy
MATERIALS
(.172)4.39 4.50
(.177)
Ø4.90(.193 DIA) (.193 DIA)
Ø4.90Ø2.40
(.094 DIA)
6.10(.240)
4.39(.172) (.240)
6.10
(.094 DIA)
Ø4.90(.193 DIA) Ø2.40
4.50(.177)
0.60
Ø4.90(.193 DIA)
0.76
(.030
)
(.024
)
PANEL CUT-OUT
WITH FLAT
WITH KEYWAY
ELECTRICAL FUNCTIONS
1 3 1 2 3
Function 1 Other function
TERMINALS
(.027)
(.129
)3.
30
0.70
Straight P0
(.029)0.75
(.059)1.50
(.059
)1.
50
Solder lug S0
PAN
EL S
WIT
CH
ES
2
BASIC PART NUMBER
SERIES
ZL
3 Single pole
NUMBER OF POLES
S0 Solder lug
P0 Straight PC
TERMINALS
OPTIONS
0 Brass, gold plated
1 Brass, silver plated
3 Brass, gold plated(1.27 micron gold)
CONTACT AND TERMINAL MATERIALS
01 Threaded, with flat
02 Threaded, with keyway
BUSHINGS
00 Standard model
MODELS
BUILD YOUR PART NUMBER
ELECTRICAL FUNCTIONS
1 ON - OFF
6 ON - ON
9 ON OFF ON
7 MOM OFF MOM
8 ON OFF MOM
2 ON - MOM
Subminiature toggle switches • metal bushing
ZL series
ABOUT THIS SERIES
Mounting accessories : Standard hardware supplied with all models : 2 hex nuts 7 mm (.275) across flats P/N U5731, 1 locking ring P/N U5821 (with keyway) or U5831 (with flat) and 1 lockwasher P/N U5841.
On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart.
PAN
EL S
WIT
CH
ES
3
SOLDER LUG TERMINALS (.094 DIA)
(.059)1.50
Ø6.00(.236 DIA)
Ø2.40
(.172)
(.100)2.54
4.00
(.157
)
5.00
(.196
)
(10-48UNS-2A)Ø4.83-48UNS-2A
8.60
(.338
)5.
505.
60(.2
20)(
.216
)
(.110
)2.
80
(.019)0.50
(.318)
4.39
8.10
213
0.50
(.019
)
24IIII II
EPOXY
FLAT
III II I
ZL31S0 ON - OFFZL36S0 ON - ONZL39S0 ON OFF ONZL37S0 MOM OFF MOMZL38S0 MOM OFF ONZL32S0 MOM - ON
Shown with threaded bushing code 01
Subminiature toggle switches • metal bushing
ZL series
STRAIGHT PC TERMINALS FLAT
III II I
ZL31P0 ON - OFFZL36P0 ON - ONZL39P0 ON OFF ONZL37P0 MOM OFF MOMZL38P0 MOM OFF ONZL32P0 MOM - ON
Ø1.10(.043 DIA)
13 2
(.094 DIA)
Ø6.00(.236 DIA)
Ø2.40
Ø4.83-48UNS-2A(10-48UNS-2A)
EPOXY
8.10(.318)
(.196
)5.
00
(.019)0.50
2.54(.100)
(.216
)8.
60(.3
38)
5.60
5.50
(.220
)
(.129
)3.
300.
50(.0
19)
II IIII
(.100
)2.
54
24
(.172)4.39
0 Brass, gold plated (standard) 1 Brass, silver plated3 Brass, gold plated (1.27 micron gold)
CONTACT & TERMINAL MATERIALS
BASIC P/N
BUSHINGS
BASIC P/N
01 Threaded, with flat02 Threaded, with keyway
00
00
PAN
EL S
WIT
CH
ES
4