Post on 18-Dec-2015
04/18/23 1
IRLP LINKING
Peter Barry,VA6PJB / KE5HQC
04/18/23 2
Topics of Discussion What is IRLP? Basic Node Set up Direct Connect to Repeater Connecting With a Link Radio How IRLP works Local IRLP Nodes Reflectors Raspberry Pi PiRLP
04/18/23 3
Invented and Programmed by Dave Cameron, VE7LTD in 1997
First nodes Vancouver and Saint John, NB… now more than 1700
04/18/23 4
04/18/23 5
04/18/23 6
How IRLP WORKS Voice-over IP (VoIP) streaming
“Speak Freely” software for voice
Runs under Linux….more stable than Windows, open source
04/18/23 7
IRLP VoIP 1. Sample analog voice with PC sound card to get a continuous mono 16-bit digital stream of raw audio at 8000Hz (120000 bps).
2. Compress the audio to reduce the size of the stream by a factor of four (32000 bps)
04/18/23 8
IRLP VoIP
4. Receive the packets on the remote host and join them back into a 4-bit stream.
3. Split the sample into small chucks (or packets)and transmit the packets to the remote host using a User Datagram Protocol (UDP) stream. UDP does NOT confirm the reception of packets, so it uses a "fire and forget" method.
.
04/18/23 9
IRLP VoIP5. Uncompress the ADPCM stream
back into an 16-bit raw stream of audio and play the raw audio stream through a digital to analog (D/A) converter (the output device of the PC sound card)
04/18/23 10
The control software controls the stream using carrier operated squelch (COS) or continuous tone coded subaudible squelch signals (CTCSS) to start and stop the stream. When COS is present, the computer detects it through the IRLP interface board.
IRLP VoIP
04/18/23 11
The PTT is controlled by the buffer which joins the split packets back into the audio stream. The IRLP interface board receives a "transmit" signal from the computer while there are packets in the buffer, and a "unkey" command when the buffer is empty.
IRLP VoIP
04/18/23 12
The user interfaces to the IRLP computer using DTMF signals sent over the radio.
DTMF sequences are owner programmable, and can accomplish almost any function imaginable.
The DTMF signals are detected on the IRLP interface board and sent directly to the computer in binary, where they are converted into numbers. A DTMF software program then runs commands on the computer depending on the code entered.
IRLP VoIP DTMF
04/18/23 13
CALGARY:
1230 VE6ZV 444.275
1810 VE6PWT 147.550 simplex
1537 VE6SQU146.895 simplex
1260 VE6OIL 146.610
(connect to SARA backbone 660* / 661*)
IRLP CALGARY AREA
04/18/23 14
AIRDRIE
1860 VE6JBJ 147.5400 simplex
OKOTOKS
1483 VE6LK 147.51
(FARS simplex, not connected to network)
IRLP CALGARY AREA
04/18/23 15
Direct connect - repeater (node) "A" connects direct with node "B".
With this type of link the two nodes are interconnected and no other IRLP connections are possible.
While repeaters "A" and "B" are connected, all local traffic on each repeater will be heard on the other repeater as well.
.
IRLP Direct Connect
04/18/23 16
Node Status www.irlp.net
IRLP Direct Connect
04/18/23 17
“Reflector” is a Linux computer with a high bandwidth connection capable of allowing many repeaters to be inter-connected together by streaming the received audio back to all other connected stations. It does not have its own radio connection..
IRLP Reflectors
04/18/23 18
Each reflector has 9 sub channels allowing up to 10 separate virtual reflectors to operate.
These are identified by the last digit. For example - 9250 is the main channel with 9251, 9252 9253 etc being virtual reflectors with identical capability as the main channel.
IRLP Reflectors
04/18/23 19
Check on reflector status at:
http://status.irlp.net
IRLP Reflectors
04/18/23 20
Check on reflector status at:
http://status.irlp.net
IRLP Reflectors
04/18/23 21
IRLP Discovery Reflector
04/18/23 22
IRLP REFLECTOR NETS
04/18/23 23
Raspberry Pi
04/18/23 24
Raspberry Pi board
04/18/23 25
PiRLP
04/18/23 26