Post on 02-Oct-2021
www.carlingtech.com 860.793.9281 sales@carlingtech.com
request sample, configure part
4M-SeriesMiniature Slide Switches
PRODUCT WEBPAGE
The 4M-Series miniature slide switches offer a variety of ratings, circuits, contact materials, and terminal platings. With 14 termination choices and 8 actuator styles, this versatile switch adapts to a variety of applications, and is able to withstand temperatures from -30°C to +85°C.
Typical Applications ∙ Consumer Electronics ∙ Instrumentation
∙ Computer Servers / Peripherals ∙ Test / Measurement
Poles Amps VDCVAC1-2 .4-5 28125, 250
2.
Tech Specs
Contact Material Terminal Plating Rating ApprovalsG silver 1 gold over silver 5A 125VAC or 28VDC , 2A 250VACK gold 2 tin 3,5 0.4VA max 20V max (AC/DC) N/AP silver 1 tin 3,5 5A 125VAC or 28VDC , 2A 250VACQ silver 1 silver 1 5A 125VAC or 28VDC , 2A 250VACR gold 2 gold 2 0.4VA max 20V max (AC/DC) N/A
ElectricalContact Rating refer to ordering scheme
Electrical Life 30,000 make & break cycles @ full load
Contact Resistance 10 mΩ max. initial @ 2-4 VDC 100mA for both silver & gold plated contacts
Insulation Resistance 1000 MΩ min.
Dielectric Strength 1500 Volts RMS @ sea level
PhysicalOperating Temperature -30°C to +85°C
Solder Heat Resistance MIL-STD-202, Method 210
Material Case Dially phthalate (DAP) (UL 94V-0)
Slide Handle Nylon
Housing Stainless Steel
Terminal Seal Epoxy
Notes: 1 Movable contact & terminal platings: silver over copper alloy2 Movable contact & terminal platings: gold over nickel over copper alloy3 Terminals platings: tin over nickel over copper alloy, available with PC terminations only4 Non-Black, white and red colors require a minimum order of 2500 pieces5 Tin option available with PC type terminations only
E Epoxy Seal 0 without Epoxy Seal
Sample Part Number 4M1 - SSP 3 - S1 / 2 - M6 Q ESelection 1 2 3 4 5 6 7
Ordering Scheme
SSP Single Pole SDP Double Pole
( ) - momentary Switching Position: 1 2 3 2-1, 5-4 Connected Terminals 2-3, 5,61 ON NONE ON3 ON OFF ON
4M1 Miniature Slide Switch
2. POLES
3. CIRCUIT
1. SERIES
4. ACTUATOR
5. ACTUATOR COLORS
5. TERMINATION
6. CONTACTS / TERMINALS
7. EPOXY SEAL
S1 .201” heightS2 .301” heightS3 .370” heightS4 .140” height
S5 .053” height (for DPDT only)S6 .488” heightS7 .311” heightT1 .209” height (for DPDT only)
1 White2 Black3 Red4 Orange5 Yellow
6 Green7 Blue8 Brown9 Gray
M1 Solder LugM2 PCBM3 Quick ConnectM51 Wire Wrap .750M52 Wire Wrap .964M53 Wire Wrap .425M54 Wire Wrap 1.062M6 PC Mount, 90° horizontalM61 Snap-In, 90°
M7 PC Mount, 90° verticalM71 Snap-In, 90°VS2 PC Mount, U bracket, .350 heightVS3 PC Mount, U bracket, .575 heightN1 Solder Lug without mounting tabs
*Manufacturer reserves the right to change product specification without prior notice.
Configure Complete Part Number > Browse Standard Parts >
3.
Single Pole Double Pole
Actuator Options
S1 S2 S3 S4
S5 S6 S7 T1 for DPDT only
* Add 0.40 (.016) from actuatorheight for DPDT-M1 and M2 model.
* Add 0.20 (.008) from actuatorheight for DPDT-M1 and M2 model.
* Add 0.70 (.028) from actuatorheight for DPDT-M1 and M2 model.
* Add 0.40 (.016) from actuatorheight for DPDT-M1 and M2 model.
* Add 0.30 (.012) from actuatorheight for DPDT-M1 and M2 model.
* All actuator length shown is SPDT model with M1 and M2 terminals.
* Add 0.40 (.016) from actuatorheight for DPDT-M1 and M3 model.
.327[8.30]
.150[3.80]
.140[3.55]
.370[9.40]
.301[7.65].201
[5.10]
.201[5.10]
.209[5.30]
.150[3.80]
.311[7.90]
.150[3.80]
.488[12.40]
.150[3.80]
.150[3.80]
.150[3.80]
.080[2.03]
1
23
1
23
4
56
.159[4.05]
.500[12.70] .500
[12.70].185[4.70]
.030[0.75]
.150[3.80]
.693[17.60]
.150[3.80]
.156[3.95]
.185[4.70]
.030[0.75]
.190[4.83]
.080[2.03]
.421[10.70]
.689[17.50]
.091[2.30]
TRAVEL TRAVEL.240[6.10] .091
[2.30]
.217[5.50]
.366[9.30]
.240[6.10]
.248[6.30]
.260[6.60]
.772[19.60]
.772[19.60]
.150[3.80]
.150[3.80]
.053[1.35]
Dimensional Specsinches [millimeters]
4.
Termination Options
Termination Options without Mounting Tabs
M1 Standard Solder Lug
M6 Single Pole
M6 Double Pole
M2 PC Thru-Hole M3 Quick Connect M5 Wire Wrap
N1 Double Pole
N1 Single Pole
M7 Single Pole
THK .030 [0.75]
THK .030
[0.75]
THK .030
[0.75]THK
.030 [0.75]* Standard with Mounting Tabs.
'A'
1.062 [26.97].425 [10.80].964 [24.48].750 [19.05]
DIM.'A'
M5-4M5-3
CODEM5-1M5-2
OPTION
P.C.MOUNTING
P.C.MOUNTING
P.C.MOUNTING
.047[1.20]
.047[1.20]
.265[6.74]
.062[1.57]
.265[6.74]
.050[1.26]
.159[4.05]
.150[3.80]
.150[3.80]
.150[3.80]
.150[3.80]
.205[5.20]
.236[6.00]
.189[4.80]
.050[1.26]
.150[3.80]
.047[1.20]
.080[2.02]
.080[2.03]
.080[2.02]
.047[1.20]
.080[2.02]
.260[6.60]
.201[5.10]
.217[5.50]
.158[4.00]
.504[12.80]
.240[6.10]
.158[4.00]
.240[6.10]
.260[6.60]
.504[12.80]
.449[11.40]
.012[0.30]
.520[13.21]
.012[0.30]
.520[13.21]
.175[4.45]
.050[1.26]
.500[12.70]
.080[2.03]
.421[10.70]
.500[12.70]
.080[2.03]
.189[4.80]
.030[0.75]
.030[0.75]
.185[4.70]
.185[4.70]
.189[4.80]
.050[1.26]
.050[1.26].050
[1.26].375
[9.53]
1 2 3
1
23
1
2
3
4
5
6
4 5 6
.030[0.75]
.030[0.75]
.030[0.75]
.260[6.60]
.500[12.70]
.050[1.26]
.073[1.85]
.150[3.81]
.400[10.16]
.520[13.21]
.520[13.21]
.421[10.70]
.175[4.45]
.185[4.70]
.185[4.70]
.185[4.70]
.185[4.70]
DIA
.073[1.85]DIA
.073[1.85]DIA
.500[12.70]
.500[12.70]
.400[10.16]
.500[12.70]
.500[12.70]
.150[3.81]
.150[3.81]
.375[9.53]
.150[3.81]
.012[0.30]
.159[4.05]
.156[3.95]
Dimensional Specsinches [millimeters]
5.
M7 Double Pole
VS2 Single Pole
VS2 Double Pole
VS3 Single Pole
VS3 Double Pole
P.C.MOUNTING
P.C.MOUNTING
P.C.MOUNTING
P.C.MOUNTING
P.C.MOUNTING
Termination Options
.150[3.80]
.150[3.80]
.150[3.80]
.150[3.80]
.150[3.80]
.175[4.45]
.185[4.70]
.185[4.70]
.185[4.70]
.185[4.70]
.350[8.90]
.382[9.70]
.575[14.60]
.575[14.60]
.125[3.18]
.125[3.18]
.125[3.18]
.125[3.18]
.315[8.00]
.311[7.90]
.315[8.00]
.315[8.00]
.047[1.20]
.050[1.26]
.047[1.20]
.047[1.20]
.050[1.26]
.030[0.75]
.421[10.70]
.500[12.70]
.500[12.70]
.500[12.70]
.620[15.75]
.620[15.75]
.620[15.75]
.620[15.75]
.150[3.81]
.189[4.80]
.205[5.20]
.189[4.80]
.205[5.20]
.012[0.30]
.185[4.70]
.012[0.30]
.012[0.30]
.012[0.30]
.185[4.70]
.185[4.70]
.185[4.70]
.620[15.75]
.620[15.75]
.620[15.75]
.620[15.75]
.030[0.75]
.030[0.75]
.150[3.80]
.150[3.80]
.150[3.80]
.150[3.80]
.050[1.26]
.150[3.81]
.190[4.83]
.190[4.83]
.175[4.45]
.125[3.18]
.125[3.18]
.125[3.18]
.125[3.18]
.190[4.83]
.185[4.70]
.190[4.83]
.185[4.70]
.185[4.70]
.185[4.70]
.073[1.85]DIA
.073[1.85]DIA
.073[1.85]DIA
.073[1.85]DIA
.073[1.85]DIA
.205[5.20]
.012[0.30]
1
2
3
1 2 3
4 5 6
1 2 3
4 5 6
4
5
6
Dimensional Specsinches [millimeters]
6.
Authorized Sales Representatives and Distributors
About CarlingFounded in 1920, Carling Technologies is a leading manufacturer of electrical and electronic switches and assemblies, circuit breakers, electronic controls, power distribution units, and multiplexed power distribution systems. With six ISO9001 and IATF16949 registered manufacturing facilities and technical sales offices worldwide, Carling Technologies Sales, Service and Engineering teams do much more than manufacture electrical components, they engineer powerful solutions! To learn more about Carling please visit www.carlingtech.com/company-profile.
To view all of Carling’s environmental, quality, health & safety certifications please visit www.carlingtech.com/environmental-certifications.
Click on a region of the map below to find your local representatives and distributors or visit www.carlingtech.com/findarep.
EUROPE
MIDDLEEAST
SOUTHAMERICA
ASIA-PACIFICOCEANIA
AFRICAMEXICO
USA
CANADA
© Carling Technologies, Inc. Carling is a registered trademark of Carling Technologies, Inc. in the U.S. and other countries.