Post on 29-Mar-2015
4/2003 Rev 2 I.3.6 – slide 1 of 23
Session I.3.6
Part I Review of Fundamentals
Module 3 Interaction of Radiation with Matter
Session 6 Buildup and Shielding
IAEA Post Graduate Educational CourseRadiation Protection and Safety of Radiation Sources
4/2003 Rev 2 I.3.6 – slide 2 of 23
In this session we will discuss shielding for photon beams
We will also discuss the increase in photon transmission through a shield resulting from buildup
Overview
4/2003 Rev 2 I.3.6 – slide 3 of 23
HVL and TVL
The amount of shielding required to reduce the incident radiation levels by ½ is called the “half-value layer” or HVL
The HVL is dependent on the energy of the photon and the type of material.
Similarly, the amount of shielding required to reduce the incident radiation levels by 1/10 is called the “tenth-value layer” or TVL.
4/2003 Rev 2 I.3.6 – slide 4 of 23
HVL and TVL
HVL (cm) TVL (cm)Isotope Photon E
(MeV)Concrete Steel Lead Concrete Steel Lead
137Cs 0.66 4.8 1.6 0.65 15.7 5.3 2.1
60Co 1.17, 1.33
6.2 2.1 1.2 20.6 6.9 4
198Au 0.41 4.1 0.33 13.5 1.1
192Ir 0.13 to 1.06
4.3 1.3 0.6 14.7 4.3 2
226Ra 0.047 to 2.4
6.9 2.2 1.66 23.4 7.4 5.5
4/2003 Rev 2 I.3.6 – slide 5 of 23
HVL and TVL
The half value layer (HVL) and tenth value layer (TVL) are mathematically related as follows:
HVL = ln(2)
TVL = ln(10)
=TVLHVL
ln(10)
ln(2)
= ln(10)ln(2)
=2.3030.693
= 3.323
TVL = 3.323 x HVL
and
4/2003 Rev 2 I.3.6 – slide 6 of 23
Shielding
Shielding is intended to reduce the radiation level at a specific location
The amount of shielding (thickness) depends on:
the energy of the radiation the shielding material the distance from the source
4/2003 Rev 2 I.3.6 – slide 7 of 23
Inverse Square Law
If the radiation emanates from a point source, the radiation follows what is commonly known as the “Inverse Square Law” or ISL.
Most real sources which are considered to be “point” sources are actually not “point” sources. Most sources such as a 60Co teletherapy source have finite dimensions (a few cm in each direction). These sources appear to behave like point sources at some distance away but as one gets closer to the source, the physical dimensions of the source result in a breakdown of the ISL.
4/2003 Rev 2 I.3.6 – slide 8 of 23
Inverse Square Law
If the source of the radiation is not a point but is a line, a flat surface (plane) or a finite volume, the ISL does not apply (to be discussed in Session II.2.5).
However, if one is far enough away from a finite line, plane or volume, they appear to be a point and the ISL can be applied, with an acceptable error band.
For the remaining discussion, a point source will be assumed. The ISL predicts that the intensity of the radiation will decrease as the distance from the source increases even without any shielding.
4/2003 Rev 2 I.3.6 – slide 9 of 23
These photons should not strike the individual. But due to scatter, they do, so the calculated value is too low. It needs to be increased by the buildup factor.
Scatter
4/2003 Rev 2 I.3.6 – slide 10 of 23
Photon Attenuationand Absorption
Absorption refers to the total number of photons absorbed by the material (dark blue arrows)
Attenuation refers to total number of photons removed from incident beam (absorbed + scattered) (dark blue and light blue arrows)
4/2003 Rev 2 I.3.6 – slide 11 of 23
Photon Attenuation
Ix = Io e-x = Io e
where:
Ix = photon intensity after traversing x cm of some material
Io = initial or incident photon intensity
x = thickness of material (cm)
= linear attenuation coefficient (cm-1)
= density (g/cm3)
/ = mass attenuation coefficient (cm2/g)
(x)-
4/2003 Rev 2 I.3.6 – slide 12 of 23
Attenuation and Buildup
Io IxBIo I
where B1
4/2003 Rev 2 I.3.6 – slide 13 of 23
I = Io B e(-x)
primary photons + scattered photonsprimary photonsB =
If there are no scattered photons, then B = 1
If there are scattered photons, then B > 1
Buildup
4/2003 Rev 2 I.3.6 – slide 14 of 23
What amount of lead shielding is needed to reduce the dose rate beyond the shield from 1 mSv/hr to 0.02 mSv/hr for a 1 MeV photon beam?
Sample Buildup
4/2003 Rev 2 I.3.6 – slide 15 of 23
Sample Buildup
PhotonEnergy Material
4/2003 Rev 2 I.3.6 – slide 16 of 23
Sample Buildup
The mass attenuation coefficient (/) for a1 MeV photon incident on a lead shield is:
(/) = 0.0708 cm2/g
The density of lead = 11.35 g/cm3
The linear attenuation coefficient is:
(/) x = 0.0708 cm2/g x 11.35 g/cm3 = 0.804 cm-1
4/2003 Rev 2 I.3.6 – slide 17 of 23
I = Io B e(-x)
I = 1 mSv/hr
Io = 0.02 mSv/hr
B = 1 (assumed)
= 0.804 cm-1
Solve for “x”
0.02 mSv/hr = (1 mSv/hr) (1) e(-x)
Sample Buildup
4/2003 Rev 2 I.3.6 – slide 18 of 23
Sample Buildup
ln(0.02) = ln[e(-x)]-3.91 = -x
Although it is not required:x = -3.91/-0.804 = 4.86 cmThis would be the calculated value of the lead shield if scatter was not considered.
0.02 mSv/hr1 mSv/hr
= e(-x)
4/2003 Rev 2 I.3.6 – slide 19 of 23
Sample Buildup
x = 3.91
4/2003 Rev 2 I.3.6 – slide 20 of 23
Sample Buildup
x = 3.91 Let’s interpolate:when x = 4, B = 2.26when x = 2, B = 1.69
1.27 = 0.09/(2.26 - x)(2.26 - x) = 0.09/1.27 = 0.0712.26 – 0.071 = x = 2.19
(4 - 2)
(2.26 - 1.69)
(4 - 3.91)
(2.26 - x) =
4/2003 Rev 2 I.3.6 – slide 21 of 23
Solve for x using B = 2.2
I = I0 B e(-x)
0.02 mSv/hr = (1 mSv/hr) (2.2) e(-x)
ln(0.02/2.2) = ln[e(-x)]
- 4.71 = - x
so x = - 4.71/- 0.804 = 5.86 cm
The thickness of the shield increased from 4.86 cm to 5.86 cm (20%) due to buildup
Sample Buildup
4/2003 Rev 2 I.3.6 – slide 22 of 23
Skyshine
Photons can scatter or “bounce” off atoms in materials such as the ceiling of a room or even air molecules !
4/2003 Rev 2 I.3.6 – slide 23 of 23
Where to Get More Information
Cember, H., Johnson, T. E., Introduction to Health Physics, 4th Edition, McGraw-Hill, New York (2008)
Martin, A., Harbison, S. A., Beach, K., Cole, P., An Introduction to Radiation Protection, 6th Edition, Hodder Arnold, London (2012)
Attix, F. H., Introduction to Radiological Physics and Radiation Dosimetry, Wiley and Sons, Chichester (1986)
Firestone, R.B., Baglin, C.M., Frank-Chu, S.Y., Eds., Table of Isotopes (8th Edition, 1999 update), Wiley, New York (1999)