Post on 09-Jul-2020
Cen
ter
Mo
un
t
Center MountCenter Mount
Cen
ter
Mo
un
t •
35lb
.loa
d
rate
d
•3/
4ex
tens
ion
•71
4Se
ries
(102
9)
Rockler Centerline Limited Lifetime WarrantyWhat is covered:IfyourRocklerCenterline™Lifetimedrawerslidefailstomeetyourexpectationsatanypointintime,youmayreturnittoRocklerforreplacementofthesameorcomparablemodelatnocost.IfyouhavearecordofyourRocklerWoodworkingandHardwarepurchase(i.e.receiptorordernumber),youmaychoosetoberefundedtheoriginalpurchasepriceinstead.What is not covered:Anyamountsabovethecostofthedrawerslidetobereplaced.Forexample,installation,removal,damages,transportationorshippingcostsarenotincludedinthiswarranty.How to get service:ReturnyourproducttoyournearestRocklerWoodworkingandHardwarestoreormail(postagepaid)to:RocklerWoodworkingandHardware,ReturnsDept.,4365WillowDr,MedinaMN55340.Call1-800-376-7856formoredetailsortospeakwithacustomerservicerepresentative.Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.Formoreinformation,gotowww.rockler.com/warranty
13 ⁄8"
3/8"
Cen
ter
Mo
un
t•
35lb
.loa
d
rate
d
•3/
4ex
tens
ion
•71
4Se
ries
(102
9)
•In
stru
ctio
ns
insi
de
•M
ount
ing
sc
rew
sin
clud
ed
Cen
ter
Mo
un
t •
35lb
.loa
d
rate
d
•3/
4ex
tens
ion
•71
4Se
ries
(102
9) 13 ⁄8"
3/8"
Prod
uct i
mag
es,
incl
udin
g co
lor,
may
diff
er fr
om
actu
al p
rodu
ct a
ppea
ranc
e.
CL
CL
CL
Centerline 714 Series Center Mount Slides
1. Opentheslideandseparatethetwomembers(frictionfit).Measurethewidthofthedrawerboxand markcenterlinesonboththeundersideofthedrawerandthedraweropeninginthecabinet.
2. Positionthedrawermemberoverthecenterlineonthedrawer,withthefrontofthedrawermember flushwiththebackofthedrawerfront.Useoneoftheprovidedscrewstofastentheslidetothearea behindthedrawerfront.Next,locatetheholenearesttothecenterofthedrawerbackanddrivein onescrew.
3. Positionthecabinetmemberflushwiththefrontedgeofthecabinet.Makesuretheendslotis positionedoverthecabinet’scenterline. Fastenthefrontedgeoftheslidetothecabinet. Adjustthe backoftheslideverticallyuntillevel. Thenlooselysecuretherearmountingbrackettothecabinetwith screwsinthebracket’shorizontalslot. Note: If rear mounting bracket is used, the drawer notch must be 15⁄8" wide If the cabinet has a horizontal stringer, you may discard the rear mounting bracket and mount the cabinet member directly to the stringer.
4. Insertthedrawerbyplacingthedrawermemberbetweentheballbearingsandcarefullypushingthe draweruntilitisclosed. Removethedrawerandtightentherearmountingbracketandinstallall remainingscrewsasneeded.Re-adjustasneededtoachieveaproperfit.
*Different lengths may have different hole configurations.
Cabinet member Drawer member
Center lineRev 2/12
© Rockler Companies Inc. 2012Visit Rockler.com for the most current product information and videos or call 1-800-260-9663.
Install screw into drawer
Drawer bottom
Install screw into drawer back
Notch drawer back flush with bottom
Draw centerline on bottom of drawer and at center of cabinet opening
13⁄8"
3/8"
Plastic tack glides
Drawer Sides
Mount slide on centerline on bottom of drawer
1/4"
3/8"
Requires 1/8" clearance between
drawer side bottom edge and carcass opening