Post on 17-Jan-2016
description
. . . presents presents
SERIES 800 MOMENT BALANCE
SYSTEM
SERIES 800 MOMENT BALANCE
SYSTEM
Nobody Knows Moment Weighing Like AWS
Unique System to Moment Weigh a SPHERE
Connecting RodsEngine Blades
FanTurbineRotorCompressor
Customers Depend on AWS
More Than 30 Years Experience in Moment Weighing
Systems That Were Installed in the 1970’s Are Still Operational
Low MaintenanceIncreased Productivity
GE Aircraft Engines Group
Proved the AWS Method is Most Accurate
AWS Equipment Specified For ALL FacilitiesEngine BladeEngine AssemblyEngine
Maintenance
So reliable is AWSequipment, that in 1982GE awarded a Class 0ne, Group One QC CodeRating; making AWS a self-certified vendor.
PRATT & WHITNEY AIRCRAFT
Engine Blades Manufactured by:HOWMET CorporationI.E.P.I.TURBO PRODUCTSNEW ENGLAND AIR FOIL
Approved for Use on all P&W Engines
U.S. Air ForceU.S. Air ForceUnits in
Service:
Kelly AFB (3) Travis AFB (2) Altus AFB Dover AFB
Engine Maintenance
& Overhaul
Total Time to Balance an Engine Reduced by More Than 30%
BLADE MOMENT BALANCE
BASE ASSEMBLY
Tubular Steel Construction
Sand Filled to Eliminate “Ringing”
Adjustable Feet for Leveling
Custom HOUSING
Eliminates Air Currents About the System
LEXAN and Aluminum Tube Construction
Sliding Doors Allow Full Access
Time Proven AWS Weigh Cell
Patented Mass Balance, Hydraulic Dampening
Readings Obtained in Less Than 150 Milli-seconds
Accuracy to 0.01% of Full Scale
Counterbalanced for Tooling and “Master” Load
SCALE Assembly
RANGE OPTIONSRANGE OPTIONS
GRAM / INCHES OUNCE / INCHESMODEL RANGE TOTAL
CAPACITYRANGE TOTAL
CAPACITY802 1,500 15,000 50.00 500.00803 2,000 20,000 80.00 800.00804 5,000 50,000 150.00 1,500.00806 10,000 100,000 300.00 3,000.00808 20,000 200,000 800.00 8,000.00
808/EX 20,000 300,000 800.00 12,000.00
RESOLUTION = 0.001% of TOTAL CAPACITY
CUSTOM Designed & Manufactured Blade
ToolingDesigned to Critically Hold Blade
as It Will Be InstalledActual Moment As If Installed In
Disk AssemblyMatched to Scale For Superior
Accuracy
CRADLE Assembly
Computer Configuration Pentium III Compatible or Better MS/DOS 6.22 1 Serial Port
– 1 (9 Pin) for the Input From the Scale
2 Parallel Ports– 1 for the Label Printer– 1 for the Report Printer
Moment Software(version 9.3)
Interactive Prompts for Each Operation
Part Data Entry/Modification in Less Than a Minute
All Settings Password Protected From Unauthorized Changes
Prompted Scale Set-Up and Calibration
Ease of Use
Minimal Time for Part Selection & Changeover
Four Screws to Remove & Replace The Cradle
Menu Selection to Change Software Part Specifications
Reference the “MASTER” for the New Part
Limited Operator Data Input Eliminates Transcription and Entry
ErrorsAUTOMATIC Data RecordingIndividual Piece Serial NumberingOperator IDMeasurement Result
Part Sorting and Data Retrieval
Sort to Groups Sort for Matched Pairs Sort Pairs to Matched Sets Absolute Sort of Complete
Assembly Data to Labels, Reports, and Files
THEORY OF OPERATION The MOMENT is Measured
From the Centerline of the Assembly, Rather Than Some Arbitrary Point .
Computes the “MOMENT” by Determining the Difference (plus or minus 10% of the Total) from the MASTER or OPTIMUM Blade Moment..
RESULT: The AWS Method Renders Results That Are At Least 10 Times More Accurate Than Other Methods Of Moment Determination.
MOMENT is a factor of the mass of the part, times the distance of the Center of Mass from the Centerline of the Scale Assembly
OPERATIONAfter the the System Setup, The
Operator Follows These Steps: Enters Individual Operator ID Selects the Part to be Measured Inserts a “MASTER” Blade into the
Cradle for Referencing Removes the “MASTER,” Inserts a
Part to be Measured
After Closing the Housing Doors, Allows the Scale to Settle, Pushes the
F5 Key, Enters the Part Serial Number and Press the ENTER Key
The Label is Printed and the Measurement Data is Saved to a File
The Operator Continues Inserting Parts Until a Sufficient Number for Accurate Classification Have Been Measured
The Entire Process of Loading a Part intothe Cradle, Closing the Housing Door, Measuring the Part, Removing It, and Affixing the Label; Takes Less Time ThanIt Is Taking Me to Tell You About It!
Cost BenefitsIncreased Productivity Up to 10 Parts Per Minute Limited Operator Data Entry Between
Parts One Scale Can Measure Several Parts More Than 35% Reduction in TOTAL Time
to Balance an Engine
Economical Operation 115 VAC/60Mhz Power
Minimum Operator Training Required
Advantages of the AWS System
Unmatched AccuracyMechanically Provable “In the Field”Ease of UseSelectable Part Sorting MethodsIncreased ProductivityEconomy of Operation
TO FIND OUT MORE, Contact:
Inside Sales: Advance Weight Systems, Inc.
409 North Main Street; P.O. Box 6
Grafton, OH 44044Telephone: (440) 926-3691FAX: (440) 926-2142
http://www.advancew8.com